Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Samsung ML85 — Trang 6/7

Code: 3-050

Description: ENGINE ERROR or PLEASE WAIT message on the LCD of the operator panel or monitor screen.
Causes: 1. Harness between the engine and control boards. 2. Engine board. Defective interface between the engine and control boards(DCU error code 78)
Remedy: 1. Check the harness between the engine and control boards. 2-1. Check if the engine board works properly when the printer resets. U5 pin 1 should be below 0.7V for about 122 ms after power on, then remain over 3.5V. - Check U5 pin 2 = approx. 3.8V. If so, check R54 or R55. - Check U5 pin 3 = approx. 4V. If so, check R53, R56, or C35. - If the voltages are normal, and U5 pin 1 is below 0.7V, replace U5. - If all are normal, check CPU pin 55. If OK, replace CPU. 2-2. Check X1 oscillation (6.94407MHz). 2-3. Replace EPROM in the Engine board. 2-4. If all above are OK, replace CPU.

Code: 3-060

Description: While printing, ‘MEMORY OVERFLOW’ message displays on monitor screen.
Causes: Control boards. Insufficient printer memory.
Remedy: Install optional SIMM memory in the control boards.

Code: 3-070

Description: While initializing, ‘Warming’ message displays on monitor screen.
Causes: Engine board. Motor Drive Circuit
Remedy: Check the U1(SMA7029M) or JP64

Code: 3-080

Description: Main motor not driving while printing, and paper not feeding into printer, resulting ‘JAM 0’.
Causes: Engine board. 1. Motor harness may be defective. 2. R7 changed value. 3. U1 defective.
Remedy: 1. Check the motor harness. If defective or damaged, replace. 2. Check R7=5.6kohm or 1kohm. Replace with 5.6Kohm. 3-1. Perform DCU diagnostic mode 00 and check the motor. 3-2. In DCU mode 00, check for pulses at U1 pin 5 and pin 14. If not, check related parts. 3-3. In DCU mode 00, check U1 pins 2 and 11 are over 4V. If the pins are below 1V, check Q2, D3 and D8. 3-4. If all above are OK, replace U1.

Code: 3-090

Description: While operating, high level sound
Causes: LSU, Motor bracket, Impella, Developer, gear, Fuser, foreign substance, etc. 1. LSU motor , Main motor bracket or wiring Developer or Fuser gears Foreign substance
Remedy: Replace the LSU Check Main motor bracket or wiring Pick-up ass’y’s rolls Reassemble or replace the Developer and the Fuser

Code: 3-100

Description: When system power is turned on, the printer does not turn on.
Causes: Engine board. 1-1. Harness between engine and control boards. 1-2. Defective harness between the control board and panel. 1-3. Fuse F151 2-1. Fuse F101
Remedy: 1-1. Check the harness between engine and control boards. If defective or damaged, replace. 1-2. Check the harness between control board and operator panel. If defective or damaged, replace. 1-3. Check F151 on the engine board. If open, measure the resistance between 5V and ground. If below50ohm, it is shorted. 2-1. Check F101 on the engine board. If open, check : - open R114 - Q102 shorted D-S, G-D, G-S - Defective DB101

Code: 3-110

Description: When printing, vertical line gets curved.
Causes: LSU and Engine board. 1. For LSU, +24V supply is unstable in the Engine board 2. Difference according LSU vendors.
Remedy: If the Q9 is KSE171, replace it to KSB1151. Check the capacitor between CN3#5 and JP60: 100nF. Check the resistor between Q5#collector and JP92: 12.1Kohm

Code: 3-120

Description: When turning on, all LED are continuously lightening.
Causes: Fuser, LSU, Engine board. 1. Fuser error 2. Paper is broken behind transfer roller. 3. Connectivity between Engine board and Video Controller.
Remedy: 1. Replace the Fuser. 2. Replace the LSU. 3. Check the wiring between the Engine board and the Video Controller.
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie