Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Sharp MXM950 — Trang 27/30

Code: U6-22

Description: LCC 24V power abnormality. DC 24V is not supplied to the LCC
Causes: Connection trouble or disconnection of the connector and the harness. LCC control PWB trouble. Power source unit trouble.
Remedy: Check the connector and the harness in the power source line. Check that the power unit and the LCC control PWB is of 24V.

Code: U6-23

Description: A3LCC tray lock detection trouble (Reverse winding). The LCC tray wire is wound in reverse
Causes: Reverse winding SW-ON. The wire is wound in reverse. Reverse winding detection SW trouble. Connection trouble of the connector and the harness. LCC control PWB trouble.
Remedy: Check the wire. Replace the reverse winding SW and the LCC control PWB. Check connection of the connector and the harness.

Code: U6-24

Description: A3LCC tray lock detection trouble. The LCC tray lock function does not operate normally
Causes: Tray lock mechanism trouble. Tray lock sensor trouble. Connection trouble of the connector and the harness. LCC control PWB trouble.
Remedy: Check the tray lock mechanism. Replace the tray lock sensor and the LCC control PWB. Check connection of the connector and the harness.

Code: U6-28

Description: LCT1 paper feed position abnormality. When the lift-up operation is started, the upper limit sensor is turned OFF before the pick-up SOL is turned ON. (Normally the upper limit sensor is turned OFF only after turning ON the pick-up SOL.)
Causes: Sensor abnormality, connector and harness connection trouble, PWB trouble. The pick-up roller is kept in the lower position mechanically.
Remedy: Use Sim. 4-2 and Sim. 4-3 to check the operation of the upper limit sensor and the lift-up operation, and check the wiring.

Code: U6-29

Description: LCT1 lift-up trouble. When lifting up, the upper limit is not detected within the specified time (A4 LCC: 10 sec, A3 LCC: 8 sec)
Causes: Upper limit sensor abnormality, tray lift-up motor lock, connector/harness connection trouble, PWB trouble
Remedy: Use Sim. 4-2 and Sim. 4-3 to check the operation of the upper limit sensor and the lift-up operation, and check the wiring. After making the countermeasure for the trouble section, use Sim. 15 to cancel the trouble.

Code: U6-33

Description: LCT2 lift-down trouble. The lower limit position (full state) of the LCT2 tray is not detected within the specified time (A4: 10sec, A3: 8sec) from starting lowering.
Causes: Remaining quantity sensor abnormality, LCT2 tray lift-up motor lock, connector/harness connection trouble, PWB trouble.
Remedy: Use Sim. 4-2 and Sim. 4-3 to check the operation of the remaining quantity sensor and the LCT2 tray lift-up motor, and check the wiring.

Code: U6-38

Description: LCT2 paper feed position abnormality. When the lift-up operation is started, the upper limit sensor is turned OFF before the pick-up SOL is turned ON. (Normally the upper limit sensor is turned OFF only after turning ON the pick-up SOL.)
Causes: Sensor abnormality, connector and harness connection trouble, PWB trouble. The pick-up roller is kept in the lower position mechanically.
Remedy: Use Sim. 4-2 and Sim. 4-3 to check the operation of the upper limit sensor and the lift-up operation, and check the wiring.

Code: U6-39

Description: LCT2 lift-up trouble. When lifting up, the upper limit is not detected within the specified time (A4 LCC: 10 sec, A3 LCC: 8 sec)
Causes: Upper limit sensor abnormality, tray lift-up motor lock, connector/harness connection trouble, PWB trouble.
Remedy: Use Sim. 4-2 and Sim. 4-3 to check the operation of the upper limit sensor and the lift-up operation, and check the wiring. After making the countermeasure for the trouble section, use Sim. 15 to cancel the trouble.
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie