Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Toshiba e-Studio 2000AC — Trang 19/29

Code: E430

Description: Cover open jam Paper Jam in Printer - Please Clear Paper Path. ADU open jam
Causes: Side cover switch LGC board
Remedy: Side cover switch • Is the switch working? (Perform the input check: FS-03-[F3]ON[4]/[A]) • Connector check (CN342, J735, J754) • Harness check LGC board • Board check • Connector check (CN342) • Harness check

Code: E440

Description: Cover open jam Paper Jam in Printer - Please Clear Paper Path. Jam access cover open jam
Causes: Jam access cover opening/ closing switch PFU board LGC board
Remedy: Jam access cover opening/ closing switch • Is the switch working? (Perform the input check: FS-03-[F3]ON[4]/[A]) • Connector check (CN925, J934, J935) • Harness check PFU board • Board check • Connector check (CN920, J805) • Harness check LGC board • Board check • Connector check (CN368) • Harness check

Code: E450

Description: Cover open jam Paper Jam in Printer - Please Clear Paper Path. LCF side cover open jam
Causes: LCF side cover opening/ closing switch LCF board PFC board LGC board
Remedy: LCF side cover opening/ closing switch • Is the switch working? (Perform the input check: FS-03-[F1]ON/[9]/[A]) • Connector check (CN7, CN70) • Harness check LCF board • Board check • Connector check (CN1, CN7) • Harness check PFU board • Board check • Connector check (CN923, CN920) • Harness check LGC board • Board check • Connector check (CN368) • Harness check

Code: E480

Description: Cover open jam Paper Jam in Printer - Please Clear Paper Path. Bridge unit front cover open jam
Causes: Bridge unit cover opening/ closing detection sensor LGC board
Remedy: Bridge unit cover opening/ closing detection sensor • Is the sensor working? (Perform the input check: FS-03-[ALL]OFF/[7]/[B]) • Connector check (J805) • Harness check LGC board • Board check • Connector check (CN343) • Harness check

Code: E490

Description: Cover open jam Paper Jam in Printer - Please Clear Paper Path. Job separator cover open jam
Causes: Job separator cover switch LGC board
Remedy: Job separator cover switch • Is the Job separator cover switch working? (Perform the input check: FS-03-[ALL]OFF[7]/[B]) • Connector check (CN260, CN261) • Harness check LGC board • Board check • Connector check (CN343) • Harness check

Code: E510

Description: Paper transport jam (ADU section) Paper Jam in Automatic Duplexing Unit - Please Clear Paper Path. Paper not reaching the ADU entrance sensor jam
Causes: Feed or transport roller possibly causing multiple feeding Sensor in the jamming area Refer to the table below. LGC board
Remedy: 1 Jamming transport path Open the cover of the unit/area whose picture is flashing on the control panel and remove any paper on the transport path. 2 Feed or transport roller possibly causing multiple feeding Check the feed roller. 3 Sensor in the jamming area • Sensor check (Refer to the table below) • Harness check • Connector check 4 LGC board • Harness check • Connector check • Board check Notes: If the jam is occurring in the ADU, PFC, PFU, CFD, LCF or PFP, check the board in each unit.

Code: E520

Description: Paper transport jam (ADU section) Paper Jam in Automatic Duplexing Unit - Please Clear Paper Path. Paper stopping in the ADU jam
Causes: ADU entrance sensor ADU clutch LGC board ADU board Rollers in the ADU Replace it if it is worn out. Pressure spring
Remedy: ADU entrance sensor • Sensor check (Perform the input check: FS-03-[ALL]OFF/[9]/[H]) • Connector check (J825, CN421) • Harness check LGC board • Board check • Connector check (CN369) • Harness check ADU board • Board check • Connector check (J810, CN420, CN421) • Harness check ADU motor • Motor check (Perform the output check: FS-03-110/160) • Connector check (J811, CN422) • Harness check • Bracket check

Code: E550

Description: Other paper jam Paper Jam in the engine. Please clear paper path Paper remaining jam on the transport path
Causes: Feed or transport roller possibly causing multiple feeding Sensor in the jamming area Refer to the table below. LGC board
Remedy: 1 Jamming transport path Open the cover of the unit/area whose picture is flashing on the control panel and remove any paper on the transport path. 2 Feed or transport roller possibly causing multiple feeding Check the feed roller. 3 Sensor in the jamming area • Sensor check (Refer to the table below) • Harness check • Connector check 4 LGC board • Harness check • Connector check • Board check Notes: If the jam is occurring in the ADU, PFC, PFU, CFD, LCF or PFP, check the board in each unit.
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie