Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Toshiba e-Studio 2000AC — Trang 21/29

Code: E726

Description: RADF jam Paper Jam in Automatic Document Feeder - Please Clear Paper Path. Transport/exit signal reception jam
Causes: RADF board SYS board Switching power supply
Remedy: RADF board • Board check • Connector check • Harness check SYS board • Board check • Connector check • Harness check Switching power supply • Check if the 24V and 5V outputs of the switching power supply are normal. • Board check • Connector check • Harness check

Code: E731

Description: RADF jam Paper Jam in Automatic Document Feeder - Please Clear Paper Path. Original stopping at the original exit/reverse sensor jam
Causes: Original exit/reverse sensor RADF board Exit roller Replace it if it is worn out.
Remedy: Exit roller Clean the exit roller if it is stained. Original exit/reverse sensor • Sensor check (Perform the input check: FS-03-[F3] ON[7]/[E]) • Connector check (J93, CN75) • Harness check RADF board • Board check • Connector check (CN75) • Harness check

Code: E860

Description: RADF jam Paper Jam in Automatic Document Feeder - Please Clear Paper Path. RADF jam access cover open jam
Causes: RADF jam access cover sensor RADF board
Remedy: RADF jam access cover sensor • Switch check (Perform the input check: FS-03-[F3] ON[7]/[C]) • Connector check (CN75, J92, J97) • Harness check RADF board • Board check • Connector check (CN75) • Harness check

Code: E870

Description: RADF jam Paper Jam in Automatic Document Feeder - Please Clear Paper Path. RADF open jam
Causes: Platen sensor LGC board
Remedy: Platen sensor • Sensor check (Perform the input check: FS-03-[F3] ON[7]/[D]) • Connector check (CN121, J1003, J1004) • Harness check LGC board • Board check • Connector check (CN121) • Harness check

Code: E910

Description: Finisher jam (Bridge unit section) Paper Jam in Printer - Please Clear Paper Path. Paper not reaching the bridge unit transport sensor- 1 jam
Causes: Bridge unit transport sensor-1 (entrance sensor) LGC board Bridge unit gate solenoid
Remedy: Paper separation failure at separation guide in the fuser unit Drawer Check that paper is not skewed in the side guides of the drawer. Leading edge margin Adjust the margin with FS-05-4402 (Leading edge position adjustment) to "Color: 5.5 mm". Widen the margin if needed. (Specification Black: 4.2 mm / Color: 5 mm) • Use A3/LD paper • It is easy to check skew with a copy of a solid image (about 10 mm on its leading edge). Refer to " "6.1.1 Adjustment Order". There are scratches on the leading paper edge Replace it if needed.Check if the guide is not deformed. Replace it if needed. All Bridge unit exit Check that Mylar on the bridge unit exit is not deformed. Replace it if needed. (E920) Finisher Check if paper jamming occurs in the finisher. Bridge unit transport sensor-1 (entrance sensor) • Sensor check (Perform the input check: FS-03- [ALL]OFF[0]/[A]) • Connector check (CN343, J607, J801) • Harness check Bridge unit gate solenoid • Solenoid check (Perform the output check: FS- 03-232) • Connector check (CN343, J607, J804) • Harness check LGC board • Board check • Connector check (CN343) • Harness check Bridge unit • Does the transport roller of the bridge unit work when the fuser motor is rotated? (Perform the output check: FS-03-113/163) • Check the drive system of the equipment and bridge unit. • Check if the rollers in the exit roller, the pressure spring and the bridge unit are worn out.

Code: E920

Description: Finisher jam (Bridge unit section) Paper Jam in Printer - Please Clear Paper Path. Paper stopping at the bridge unit transport sensor- 1 jam
Causes: Bridge unit transport sensor-1 (entrance sensor) LGC board Bridge unit gate solenoid
Remedy: Paper separation failure at separation guide in the fuser unit Drawer Check that paper is not skewed in the side guides of the drawer. Leading edge margin Adjust the margin with FS-05-4402 (Leading edge position adjustment) to "Color: 5.5 mm". Widen the margin if needed. (Specification Black: 4.2 mm / Color: 5 mm) • Use A3/LD paper • It is easy to check skew with a copy of a solid image (about 10 mm on its leading edge). Refer to " "6.1.1 Adjustment Order". There are scratches on the leading paper edge Replace it if needed.Check if the guide is not deformed. Replace it if needed. All Bridge unit exit Check that Mylar on the bridge unit exit is not deformed. Replace it if needed. (E920) Finisher Check if paper jamming occurs in the finisher. Bridge unit transport sensor-1 (entrance sensor) • Sensor check (Perform the input check: FS-03- [ALL]OFF[0]/[A]) • Connector check (CN343, J607, J801) • Harness check Bridge unit gate solenoid • Solenoid check (Perform the output check: FS- 03-232) • Connector check (CN343, J607, J804) • Harness check LGC board • Board check • Connector check (CN343) • Harness check Bridge unit • Does the transport roller of the bridge unit work when the fuser motor is rotated? (Perform the output check: FS-03-113/163) • Check the drive system of the equipment and bridge unit. • Check if the rollers in the exit roller, the pressure spring and the bridge unit are worn out.

Code: E930

Description: Finisher jam (Bridge unit section) Paper Jam in Printer - Please Clear Paper Path. Paper not reaching the bridge unit transport sensor- 2 jam
Causes: Bridge unit transport sensor-2 (exit sensor) LGC board
Remedy: Bridge unit transport sensor-2 (exit sensor) • Sensor check (Perform the input check: FS-03-[ALL]OFF[0]/[B]) • Connector check (CN343, J607, J802) • Harness check LGC board • Board check • Connector check (CN343) • Harness check Bridge unit • Does the transport roller of the bridge unit work when the fuser motor is rotated? (Perform the output check: FS-03-113/163) • Check the drive system of the equipment and bridge unit. • Check if the rollers in the exit roller, the pressure spring and the bridge unit are worn out.

Code: E940

Description: Finisher jam (Bridge unit section) Paper Jam in Printer - Please Clear Paper Path. Paper stopping at the bridge unit transport sensor- 2 jam
Causes: Bridge unit transport sensor-2 (exit sensor) LGC board
Remedy: (exit sensor) • Sensor check (Perform the input check: FS-03-[ALL]OFF[0]/[B]) • Connector check (CN343, J607, J802) • Harness check LGC board • Board check • Connector check (CN343) • Harness check Bridge unit • Does the transport roller of the bridge unit work when the fuser motor is rotated? (Perform the output check: FS-03-113/163) • Check the drive system of the equipment and bridge unit. • Check if the rollers in the exit roller, the pressure spring and the bridge unit are worn out.
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie