• Code: E063
• Description: Incorrect paper size setting for PFP upper drawer: The size of paper in the 3rd drawer differs from size setting of the equipment.
• Causes: SYS board IMG board LGC board HDD Page memory
• Remedy: Other • Remove the paper remained in front of the registration sensor) • Check if the error is cleared by turning the power OFF and then back ON. SYS board • Connector check • Board check IMG board • Connector check • Board check LGC board • Connector check • Board check HDD • Connector check • HDD check Page memory Check if the page memory is correctly connected to the connector on the SYS board.

• Code: E064
• Description: Incorrect paper size setting for PFP lower drawer: The size of paper in the 4th drawer differs from size setting of the equipment.
• Causes: SYS board IMG board LGC board HDD Page memory
• Remedy: Other • Remove the paper remained in front of the registration sensor) • Check if the error is cleared by turning the power OFF and then back ON. SYS board • Connector check • Board check IMG board • Connector check • Board check LGC board • Connector check • Board check HDD • Connector check • HDD check Page memory Check if the page memory is correctly connected to the connector on the SYS board.

• Code: E065
• Description: Incorrect paper size setting for bypass tray: The size of paper in the bypass tray differs from size setting of the equipment.
• Causes: SYS board IMG board LGC board HDD Page memory
• Remedy: Other • Remove the paper remained in front of the registration sensor) • Check if the error is cleared by turning the power OFF and then back ON. SYS board • Connector check • Board check IMG board • Connector check • Board check LGC board • Connector check • Board check HDD • Connector check • HDD check Page memory Check if the page memory is correctly connected to the connector on the SYS board.

• Code: E090
• Description: Image data delay jam: Image data to be printed cannot be prepared
• Causes: SYS board IMG board LGC board HDD Page memory
• Remedy: Other • Remove the paper remained in front of the registration sensor) • Check if the error is cleared by turning the power OFF and then back ON. SYS board • Connector check • Board check IMG board • Connector check • Board check LGC board • Connector check • Board check HDD • Connector check • HDD check Page memory Check if the page memory is correctly connected to the connector on the SYS board.

• Code: E091
• Description: Motor-ON time-out jam: The equipment does not operate normally because abnormality occurred on an interface between the SYS board and engine firmware.
• Causes: SYS board IMG board LGC board HDD
• Remedy: Other • Check if there is any paper in the equipment. Remove it if there is. • If the error still occurs, check the following. Power Check if the error is cleared by turning the power OFF and then back ON. SYS board • Connector check • Board check IMG board • Connector check • Board check LGC board • Connector check • Board check HDD • Connector check • HDD check

• Code: E0A0
• Description: Image transport ready time-out jam: Image data to be printed cannot be sent.
• Causes: LGC board
• Remedy: LGC board Connector check

• Code: E110
• Description: ADU misfeeding (Paper not reaching the registration sensor): The paper which has passed through ADU does not reach the registration sensor during duplex printing.
• Causes: Registration sensor LGC board ADU clutch Rollers in the ADU
• Remedy: Paper stop jam at the registration roller position Registration guide Check the registration guide. Replace it if needed. All Registration sensor • Sensor check (Perform the input check: 03- [ALL]OFF/[7]/[F]) • Connector check (CN337) • Harness check LGC board • Board check • Connector check (CN337, CN338) • Harness check ADU clutch • Clutch check (Perform the output check: 03- 222) • Connector check (CN338) • Harness check ADU Check if the connector between the ADU and equipment is connected.

• Code: E120
• Description: Bypass misfeeding (Paper not reaching the bypass feed sensor): Paper fed from the bypass tray does not reach the bypass feed sensor.
• Causes: Bypass feed clutch Bypass feed sensor LGC board
• Remedy: Bypass feed clutch • Clutch check (Perform the output check: 03-204 and the input check: 03-[FAX]ON/[4]/[D]) • Connector check (CN338) • Harness check Bypass feed sensor • Sensor check (Perform the output check: 03-204 and the input check: 03-[FAX]ON/[4]/[D]) • Connector check (CN338) • Harness check LGC board • Board check • Connector check (CN338) • Harness check