• Code: E190
• Description: LCF misfeeding (Paper not reaching the LCF feed sensor): The paper fed from the LCF does not reach the LCF feed sensor.
• Remedy: Open the LCF side cover. Is there any paper in front of the LCF feed sensor? → YES → Remove the paper. NO Is the LCF feed sensor working? (Perform the input check: 03-[FAX]OFF/[5]/[G]) ↓→ NO → 1) Check if the connector of the LCF feed sensor is disconnected. 2) Check if either of the connectors CN100 or CN104 on the LCF board is disconnected. 3) Check if the connector CN344 on the LGC board is disconnected. 4) Check if the connector pins are disconnected or the harnesses are open circuited. 5) Check if the conductor patterns on the LCF board and LGC board are short circuited or open circuited. 6) Replace the LCF feed sensor. 7) Replace the LCF board. 8) Replace the LGC board. YES Is the LCF feed clutch working? (Perform the output check: 03-209) ↓→ NO → 1) Check if the connector of the LCF feed clutch is disconnected. 2) Check if any of the connectors CN100, CN101 and CN103 on the LCF board is disconnected. 3) Check if the connector CN344 on the LGC board is disconnected. 4) Check if the connector pins are disconnected or the harnesses are open circuited. 5) Check if the conductor patterns on the LCF board and LGC board are short circuited or open circuited. 6) Replace the LCF feed clutch. 7) Replace the LCF board. 8) Replace the LGC board. YES Check the LCF feed roller, separation roller and pickup roller. Replace them if they are worn out.

• Code: E200
• Description: 1st drawer transport jam (Paper not reaching the registration sensor): The paper does not reach the registration sensor after it has passed the 1st drawer feed sensor.
• Remedy: Open the jam access cover. Is there paper in front of the registration sensor? → YES → Remove the paper. NO Is the registration sensor working? (Perform the input check: 03-[FAX]ON/[9]/[E]) ↓→ NO → 1) Check if the connector of the registration sensor is disconnected. 2) Check if the connector CN338 on the LGC board is disconnected. 3) Check if the connector pins are disconnected or the harnesses are open circuited. 4) Check if the conductor pattern on the LGC board is short circuited or open circuited. 5) Replace the registration sensor. 6) Replace the LGC board. YES Are the upper transport clutches (high/low speed) working? (Perform the output check: 03-439, 440) ↓→ NO → 1) Check if the connectors of the upper transport clutches (high/low speed) are disconnected. 2) Check if the connector CN339 on the LGC board is disconnected. 3) Check if the connector pins are disconnected or the harnesses are open circuited. 4) Check if the conductor pattern on the LGC board is short circuited or open circuited. 5) Replace the upper transport clutches (high/low speed). 6) Replace the LGC board. YES 1) Check the condition of the feed roller, separation roller and pickup roller of each paper source, and replace them if they are worn out. 2) Check the transport roller. Replace it if it is worn out.

• Code: E210
• Description: 2nd drawer transport jam (Paper not reaching the registration sensor): The paper does not reach the registration sensor after it has passed the 1st drawer feed sensor.
• Remedy: Open the jam access cover. Is there paper in front of the registration sensor? → YES → Remove the paper. NO Is the registration sensor working? (Perform the input check: 03-[FAX]ON/[9]/[E]) ↓→ NO → 1) Check if the connector of the registration sensor is disconnected. 2) Check if the connector CN338 on the LGC board is disconnected. 3) Check if the connector pins are disconnected or the harnesses are open circuited. 4) Check if the conductor pattern on the LGC board is short circuited or open circuited. 5) Replace the registration sensor. 6) Replace the LGC board. YES Are the upper transport clutches (high/low speed) working? (Perform the output check: 03-439, 440) ↓→ NO → 1) Check if the connectors of the upper transport clutches (high/low speed) are disconnected. 2) Check if the connector CN339 on the LGC board is disconnected. 3) Check if the connector pins are disconnected or the harnesses are open circuited. 4) Check if the conductor pattern on the LGC board is short circuited or open circuited. 5) Replace the upper transport clutches (high/low speed). 6) Replace the LGC board. YES 1) Check the condition of the feed roller, separation roller and pickup roller of each paper source, and replace them if they are worn out. 2) Check the transport roller. Replace it if it is worn out.

• Code: E220
• Description: 2nd drawer transport jam (Paper not reaching the 1st drawer feed sensor): The paper does not reach the 1st drawer feed sensor after it has passed the 2nd drawer feed sensor.
• Remedy: Open the jam access cover. Is there paper in front of the upper drawer feed sensor? → YES → Remove the paper. NO Is the upper drawer feed sensor working? (Perform the input check: 03-[FAX]ON/[3]/[H]) ↓→ NO → 1) Check if the connector of the upper drawer feed sensor is disconnected. 2) Check if the connector CN338 on the LGC board is disconnected. 3) Check if the connector pins are disconnected or the harnesses are open circuited. 4) Check if the conductor pattern on the LGC board is short circuited or open circuited. 5) Replace the upper drawer feed sensor. 6) Replace the LGC board. YES Are the lower transport clutches (high/low speed) working? (Perform the output check: 03-203, 205) ↓→ NO → 1) Check if the connectors of the lower transport clutches (high/low speed) are disconnected. 2) Check if the connector CN341 on the LGC board is disconnected. 3) Check if the connector pins are disconnected or the harnesses are open circuited. 4) Check if the conductor pattern on the LGC board is short circuited or open circuited. 5) Replace the lower transport clutches (high/low speed). 6) Replace the LGC board. YES 1) Check the condition of the feed roller, separation roller and pickup roller of each paper source, and replace them if they are worn out. 2) Check the transport roller. Replace it if it is worn out.

• Code: E300
• Description: PFP upper drawer transport jam (Paper not reaching the registration sensor): The paper does not reach the registration sensor after it has passed the 1st drawer feed sensor.
• Remedy: Open the jam access cover. Is there paper in front of the registration sensor? → YES → Remove the paper. NO Is the registration sensor working? (Perform the input check: 03-[FAX]ON/[9]/[E]) ↓→ NO → 1) Check if the connector of the registration sensor is disconnected. 2) Check if the connector CN338 on the LGC board is disconnected. 3) Check if the connector pins are disconnected or the harnesses are open circuited. 4) Check if the conductor pattern on the LGC board is short circuited or open circuited. 5) Replace the registration sensor. 6) Replace the LGC board. YES Are the upper transport clutches (high/low speed) working? (Perform the output check: 03-439, 440) ↓→ NO → 1) Check if the connectors of the upper transport clutches (high/low speed) are disconnected. 2) Check if the connector CN339 on the LGC board is disconnected. 3) Check if the connector pins are disconnected or the harnesses are open circuited. 4) Check if the conductor pattern on the LGC board is short circuited or open circuited. 5) Replace the upper transport clutches (high/low speed). 6) Replace the LGC board. YES 1) Check the condition of the feed roller, separation roller and pickup roller of each paper source, and replace them if they are worn out. 2) Check the transport roller. Replace it if it is worn out.

• Code: E310
• Description: PFP upper drawer transport jam (Paper not reaching the 1st drawer feed sensor): The paper does not reach the 1st drawer feed sensor after it has passed the 2nd drawer feed sensor.
• Remedy: Open the jam access cover. Is there paper in front of the upper drawer feed sensor? → YES → Remove the paper. NO Is the upper drawer feed sensor working? (Perform the input check: 03-[FAX]ON/[3]/[H]) ↓→ NO → 1) Check if the connector of the upper drawer feed sensor is disconnected. 2) Check if the connector CN338 on the LGC board is disconnected. 3) Check if the connector pins are disconnected or the harnesses are open circuited. 4) Check if the conductor pattern on the LGC board is short circuited or open circuited. 5) Replace the upper drawer feed sensor. 6) Replace the LGC board. YES Are the lower transport clutches (high/low speed) working? (Perform the output check: 03-203, 205) ↓→ NO → 1) Check if the connectors of the lower transport clutches (high/low speed) are disconnected. 2) Check if the connector CN341 on the LGC board is disconnected. 3) Check if the connector pins are disconnected or the harnesses are open circuited. 4) Check if the conductor pattern on the LGC board is short circuited or open circuited. 5) Replace the lower transport clutches (high/low speed). 6) Replace the LGC board. YES 1) Check the condition of the feed roller, separation roller and pickup roller of each paper source, and replace them if they are worn out. 2) Check the transport roller. Replace it if it is worn out.

• Code: E320
• Description: PFP upper drawer transport jam (Paper not reaching the 2nd drawer feed sensor): The paper does not reach the 2nd drawer feed sensor after it has passed the PFP upper drawer feed sensor.
• Remedy: Open the side cover. Is there paper in front of the lower drawer feed sensor? → YES → Remove the paper. NO Is the lower drawer feed sensor working? (Perform the input check: 03-[FAX]ON/[3]/[G]) ↓→ NO → 1) Check if the connector of the lower drawer feed sensor is disconnected. 2) Check if the connector CN338 on the LGC board is disconnected. 3) Check if the connector pins are disconnected or the harnesses are open circuited. 4) Check if the conductor pattern on the LGC board is short circuited or open circuited. 5) Replace the lower drawer feed sensor. 6) Replace the LGC board. YES Are the lower transport clutches working? (Perform the output check: 03-203, 205) ↓→ NO → 1) Check if the connectors of the lower transport clutches (high/low speed) are disconnected. 2) Check if the connector CN341 on the LGC board is disconnected. 3) Check if the connector pins are disconnected or the harnesses are open circuited. 4) Check if the conductor pattern on the LGC board is short circuited or open circuited. 5) Replace the lower transport clutches (high/low speed). 6) Replace the LGC board. YES When the paper fed from the PFP: Is the PFP transport clutch working? (Perform the output check: 03-225) ↓→ NO → 1) Check if the connector of the PFP transport clutch is disconnected. 2) Check if any of the connectors CN241, CN242 and CN244 on the PFP board is disconnected. 3) Check if the connector CN344 on the LGC board is disconnected. 4) Check if the connector pins are disconnected or the harnesses are open circuited. 5) Check if the conductor patterns on the PFP board and LGC board are short circuited or open circuited. 6) Replace the PFP transport clutch. 7) Replace the PFP board. 8) Replace the LGC board. YES 1) Check the condition of the feed roller, separation roller and pickup roller of each paper source, and replace them if they are worn out. 2) Check the transport roller. Replace it if it is worn out.

• Code: E330
• Description: PFP lower drawer transport jam (Paper not reaching the registration sensor): The paper does not reach the registration sensor after it has passed the 1st drawer feed sensor.
• Remedy: Open the jam access cover. Is there paper in front of the registration sensor? → YES → Remove the paper. NO Is the registration sensor working? (Perform the input check: 03-[FAX]ON/[9]/[E]) ↓→ NO → 1) Check if the connector of the registration sensor is disconnected. 2) Check if the connector CN338 on the LGC board is disconnected. 3) Check if the connector pins are disconnected or the harnesses are open circuited. 4) Check if the conductor pattern on the LGC board is short circuited or open circuited. 5) Replace the registration sensor. 6) Replace the LGC board. YES Are the upper transport clutches (high/low speed) working? (Perform the output check: 03-439, 440) ↓→ NO → 1) Check if the connectors of the upper transport clutches (high/low speed) are disconnected. 2) Check if the connector CN339 on the LGC board is disconnected. 3) Check if the connector pins are disconnected or the harnesses are open circuited. 4) Check if the conductor pattern on the LGC board is short circuited or open circuited. 5) Replace the upper transport clutches (high/low speed). 6) Replace the LGC board. YES 1) Check the condition of the feed roller, separation roller and pickup roller of each paper source, and replace them if they are worn out. 2) Check the transport roller. Replace it if it is worn out.