• Code: ED13
• Description: Front alignment plate home position error: The front alignment plate is not at the home position. [MJ- 1109/1110]
• Causes: Front alignment plate home position sensor (S7) Front alignment motor (M5) Finisher controller PC board (FIN)
• Remedy: Front alignment plate Move the front alignment plate. Fix any mechanical problem. Front alignment plate home position sensor (S7) Check if there is a disconnection of the connector, incorrect installation or breakage of the front alignment plate home position sensor (S7). If there is, reinstall the sensor correctly or replace it. Check if the connector (CN25) on the finisher controller PC board is disconnected from the front alignment plate home position sensor (S7) and the harnesses are open circuited. Correct if so. Front alignment motor (M5) Check if the connector (CN18) on the finisher controller PC board is disconnected from the front alignment motor (M5) and the harnesses are open circuited. Correct if so.

• Code: ED14
• Description: Rear alignment plate home position error: The rear alignment plate is not at the home position. [MJ- 1109/1110]
• Causes: Rear alignment plate home position sensor (S8) Rear alignment motor (M6) Finisher controller PC board (FIN)
• Remedy: Rear alignment plate Move the rear alignment plate. Fix any mechanical problem. Rear alignment plate home position sensor (S8) Check if there is a disconnection of the connector, incorrect installation or breakage of the rear alignment plate home position sensor (S8). If there is, reinstall the sensor correctly or replace it. Check if the connector (CN25) on the finisher controller PC board is disconnected from the rear alignment plate home position sensor (S8) and the harnesses are open circuited. Correct if so. Rear alignment motor (M6) Check if the connector (CN18) on the finisher controller PC board is disconnected from the rear alignment motor (M6) and the harnesses are open circuited. Correct if so.

• Code: ED14
• Description: Rear alignment plate home position error: The rear alignment plate is not at the home position. [MJ- 1109/1110]
• Causes: Rear alignment plate home position sensor (S8) Rear alignment motor (M6) Finisher controller PC board (FIN)
• Remedy: Rear alignment plate Move the rear alignment plate. Fix any mechanical problem. Rear alignment plate home position sensor (S8) Check if there is a disconnection of the connector, incorrect installation or breakage of the rear alignment plate home position sensor (S8). If there is, reinstall the sensor correctly or replace it. Check if the connector (CN25) on the finisher controller PC board is disconnected from the rear alignment plate home position sensor (S8) and the harnesses are open circuited. Correct if so. Rear alignment motor (M6) Check if the connector (CN18) on the finisher controller PC board is disconnected from the rear alignment motor (M6) and the harnesses are open circuited. Correct if so.

• Code: ED15
• Description: Paddle home position error: The paddle is not at the home position. [MJ-1109/1110]
• Causes: Paddle motor (M3) Paddle home position sensor (S3) Finisher control PC board (FIN)
• Remedy: Paddle Rotate the paddle. If there is any mechanical problem, fix its mechanism. Paddle home position sensor Paddle motor Finisher controller PC board Check if the connectors (CN15, CN16) on the finisher control PC board are disconnected from the paddle home position sensor (S3) and the paddle motor (M3), or the harnesses are open circuited. Correct if any.

• Code: ED16
• Description: Buffer tray home position error: The buffer tray is not at the home position. [MJ-1109/1110]
• Causes: Buffer tray home position sensor (S5) Assist arm motor (M10) Buffer tray guide motor (M2) Finisher controller PC board (FIN)
• Remedy: Buffer tray guide Open and close the buffer tray guide. Fix any mechanical problem. Buffer tray home position sensor (S5) Check if there is a disconnection of the connector, incorrect installation or breakage of the buffer tray home position sensor (S5). If there is, reinstall the sensor correctly or replace it. Check if the connector (CN11) on the finisher controller PC board is disconnected from the buffer tray home position sensor (S5) and the harnesses are open circuited. Correct if so. Assist arm motor (M10) Check if the connector (CN10) on the finisher controller PC board is disconnected from the assist arm motor (M10) and the harnesses are open circuited. Correct if so. Buffer tray guide motor (M2) Check if the connector (CN10) on the finisher controller PC board is disconnected from the buffer tray guide motor (M2) and the harnesses are open circuited. Correct if so.

• Code: EF10
• Description: Paper not supported for Saddle Stitch Finisher: Unsupported paper size, type and an excess number of pages for stapling are selected. [MJ- 1110]
• Causes:
• Remedy: Check the paper size, paper type, or number of pages for stapling. Change them if they are unsupported.

• Code: EF11
• Description: Saddle Stitch Finisher stapling error (front): Front stapling is not correctly done. [MJ-1110]
• Causes: Front saddle stapler drive unit Saddle control PC board (SDL)
• Remedy: Paper • Check if there is any paper in the hole punch unit, finisher or the on the transport path of the equipment. Remove it if there is. • Use paper accepted in the specifications. Staple cartridge (front side) • Is the jam released by taking off the front staple cartridge from the Finisher and removing the staple sheet slid from the staple case? Front saddle stapler drive unit • Unit check • Connector check • Harness check Saddle control PC board (SDL) • Connector check (CN2) • Board check

• Code: EF12
• Description: Saddle Stitch Finisher stapling error (rear): Rear stapling is not correctly done. [MJ-1110]
• Causes: Rear saddle stapler drive unit Saddle control PC board (SDL)
• Remedy: Paper • Check if there is any paper in the hole punch unit, finisher or the on the transport path of the equipment. Remove it if there is. • Use paper accepted in the specifications. Staple cartridge (rear side) • Is the jam released by taking off the rear staple cartridge from the Finisher and removing the staple sheet slid from the staple case? Rear saddle stapler drive unit • Unit check • Connector check • Harness check Saddle control PC board (SDL) • Connector check (CN1) • Board check