• Code: EB60
• Description: Paper remaining on the transport path: The multiple feeding of preceding paper caused the misfeeding of upcoming paper (redetection after no jam is detected at [EB50]).
• Causes: Registration sensor DRV board LGC board Rollers
• Remedy: Registration sensor • Sensor check (Perform the input check: 03-[ALL]OFF/[9]/[A]) • Connector check (CN462, J1114, J1077) • Harness check DRV board • Board check • Connector check (CN462, CN450, CN451) • Harness check LGC board • Connector check (CN361, CN362) • Board check Drive unit, Rollers • Gear check • Roller check

• Code: ED10
• Description: Skew adjustment motor (M1) home position detection abnormality: The Skew adjustment motor is not at the home position. [MJ-1107/ 1108 (when MJ-6104 is installed)]
• Causes: Skew adjustment motor Skew HP sensor Hole punch control PC board
• Remedy: Skew adjustment motor (M1) Rotate skew adjustment motor and fix its mechanism if it does not rotate smoothly. Skew HP sensor (S2) Skew adjustment motor (M1) Hole punch control PC board Check if the connectors on the hole punch controller PC board (HP board) are disconnected from the skew HP sensor (S2) and the skew adjustment motor, or the harnesses are open circuited. Correct if any.

• Code: ED11
• Description: Sideways adjustment motor (M2) home position detection error: The Sideways adjustment motor is not at the home position. [MJ-1107/1108 (when MJ-6104 is installed)]
• Causes: Sideways adjustment motor Sideways deviation HP sensor Hole punch control PC board
• Remedy: (M2) Rotate sideways adjustment motor and fix its mechanism if it does not rotate smoothly. Sideways deviation HP sensor (S3) Sideways adjustment motor (M2) Hole punch control PC board Check if the connectors on the hole punch controller PC board (HP board) are disconnected from the sideways deviation HP sensor (S3) and the sideways adjustment motor, or the harnesses are open circuited. Correct if any.

• Code: ED12
• Description: Shutter home position error: The shutter is not at the home position. [MJ-1107/1108]
• Causes: MJ-1107 Movable tray paper-full sensor Shutter opening/closing sensor Shutter clutch Finisher controller PC board
  MJ-1108 Movable tray paper-full sensor Shutter opening/closing sensor Shutter clutch Finisher controller PC board
• Remedy: MJ-1107 Movable tray paper-full sensor Fix any mechanical problem occurring when the actuator is moved. Check if there is a disconnection of the connector, incorrect installation or breakage of the movable tray paper-full sensor (S16). If there is, reinstall the sensor correctly or replace it. Check if the connector (CN13) on the finisher controller PC board is disconnected from the movable tray paper-full sensor (S16) and the harnesses are open circuited. Correct if so. Shutter Open and close the shutter. Fix any mechanical problem. Shutter opening/closing sensor Check if there is a disconnection of the connector, incorrect installation or breakage of the shutter opening/closing sensor (S4). If there is, reinstall the sensor correctly or replace it. Check if the connector (CN13) on the finisher controller PC board is disconnected from the shutter opening/closing sensor (S4) and the harnesses are open circuited. Correct if so. Shutter clutch Check if the connector (CN5) on the finisher controller PC board is disconnected from the shutter clutch (CLT1) and the harnesses are open circuited. Correct if so.
  MJ-1108 Movable tray paper-full sensor Fix any mechanical problem occurring when the actuator is moved. Check if there is a disconnection of the connector, incorrect installation or breakage of the movable tray paper-full sensor (S16). If there is, reinstall the sensor correctly or replace it. Check if the connector (CN12) on the finisher controller PC board is disconnected from the movable tray paper-full sensor (S16) and the harnesses are open circuited. Correct if so. Shutter Open and close the shutter. Fix any mechanical problem. Shutter opening/closing sensor Check if there is a disconnection of the connector, incorrect installation or breakage of the shutter opening/closing sensor (S4). If there is, reinstall the sensor correctly or replace it. Check if the connector (CN12) on the finisher controller PC board is disconnected from the shutter opening/closing sensor (S4) and the harnesses are open circuited. Correct if so. Shutter clutch Check if the connector (CN10) on the finisher controller PC board is disconnected from the shutter clutch (CLT1) and the harnesses are open circuited. Correct if so.

• Code: ED13
• Description: Front alignment plate home position error: The front alignment plate is not at the home position. [MJ-1107/1108]
• Causes: MJ-1107 Front alignment plate home position sensor Front alignment motor Finisher controller PC board
  MJ-1108 Front alignment plate home position sensor Front alignment motor Finisher controller PC board
• Remedy: MJ-1107 Front alignment plate Move the front alignment plate. Fix any mechanical problem. Front alignment plate home position sensor Check if there is a disconnection of the connector, incorrect installation or breakage of the front alignment plate home position sensor (S7). If there is, reinstall the sensor correctly or replace it. Check if the connector (CN11) on the finisher controller PC board is disconnected from the front alignment plate home position sensor (S7) and the harnesses are open circuited. Correct if so. Front alignment motor Check if the connector (CN10) on the finisher controller PC board is disconnected from the front alignment motor (M9) and the harnesses are open circuited. Correct if so.
  MJ-1108 Front alignment plate Move the front alignment plate. Fix any mechanical problem. Front alignment plate home position sensor Check if there is a disconnection of the connector, incorrect installation or breakage of the front alignment plate home position sensor (S7). If there is, reinstall the sensor correctly or replace it. Check if the connector (CN18) on the finisher controller PC board is disconnected from the front alignment plate home position sensor (S7) and the harnesses are open circuited. Correct if so. Front alignment motor Check if the connector (CN17) on the finisher controller PC board is disconnected from the front alignment motor (M5) and the harnesses are open circuited. Correct if so.

• Code: ED14
• Description: Rear alignment plate home position error: The rear alignment plate is not at the home position. [MJ-1107/1108]
• Causes: MJ-1107 Rear alignment plate home position sensor Rear alignment motor Finisher controller PC board
  MJ-1108 Rear alignment plate home position sensor Rear alignment motor Finisher controller PC board
• Remedy: MJ-1107 Rear alignment plate Move the rear alignment plate. Fix any mechanical problem. Rear alignment plate home position sensor Check if there is a disconnection of the connector, incorrect installation or breakage of the rear alignment plate home position sensor (S8). If there is, reinstall the sensor correctly or replace it. Check if the connector (CN11) on the finisher controller PC board is disconnected from the rear alignment plate home position sensor (S8) and the harnesses are open circuited. Correct if so. Rear alignment motor Check if the connector (CN10) on the finisher controller PC board is disconnected from the rear alignment motor (M10) and the harnesses are open circuited. Correct if so.
  MJ-1108 Rear alignment plate Move the rear alignment plate. Fix any mechanical problem. Rear alignment plate home position sensor Check if there is a disconnection of the connector, incorrect installation or breakage of the rear alignment plate home position sensor (S8). If there is, reinstall the sensor correctly or replace it. Check if the connector (CN18) on the finisher controller PC board is disconnected from the rear alignment plate home position sensor (S8) and the harnesses are open circuited. Correct if so. Rear alignment motor Check if the connector (CN17) on the finisher controller PC board is disconnected from the rear alignment motor (M6) and the harnesses are open circuited. Correct if so.

• Code: ED15
• Description: Paddle home position error: The paddle is not at the home position. [MJ-1107/1108]
• Causes: MJ-1107 Paddle motor Paddle home position sensor Finisher controller PC board
  MJ-1108 Paddle motor Paddle home position sensor Finisher controller PC board
• Remedy: MJ-1107 Paddle Rotate the paddle. If there is any mechanical problem, fix its mechanism. Paddle home position sensor Paddle motor Finisher controller PC board Check if the connectors on the finisher controller PC board are disconnected from the paddle home position sensor (S3) and the paddle motor (M8), or the harnesses are open circuited. Correct if any.
  MJ-1108 Paddle Rotate the paddle. If there is any mechanical problem, fix its mechanism. Paddle home position sensor Paddle motor Finisher controller PC board Check if the connectors on the finisher controller PC board are disconnected from the paddle home position sensor (S3) and the paddle motor (M3), or the harnesses are open circuited. Correct if any.

• Code: ED16
• Description: Buffer tray home position error: The buffer tray is not at the home position. [MJ-1107/1108]
• Causes: MJ-1107 Buffer tray home position sensor Buffer tray guide motor Finisher controller PC board
  MJ-1108 Buffer tray home position sensor Assist arm motor Buffer tray guide motor Finisher controller PC board
• Remedy: MJ-1107 Buffer tray guide Open and close the buffer tray guide. If there is any mechanical problem, fix its mechanism. Buffer tray home position sensor Buffer tray guide motor Finisher controller PC board Check if the connectors on the finisher controller PC board are disconnected from the buffer tray home position sensor (S5) and the buffer tray guide motor (M3), or the harnesses are open circuited. Correct if any.
  MJ-1108 Buffer tray guide Open and close the buffer tray guide. Fix any mechanical problem. Buffer tray home position sensor Check if there is a disconnection of the connector, incorrect installation or breakage of the buffer tray home position sensor (S5). If there is, reinstall the sensor correctly or replace it. Check if the connector (CN11) on the finisher controller PC board is disconnected from the buffer tray home position sensor (S5) and the harnesses are open circuited. Correct if so. Assist arm motor Check if the connector (CN13) on the finisher controller PC board is disconnected from the assist arm motor (M10) and the harnesses are open circuited. Correct if so. Buffer tray guide motor Check if the connector (CN11) on the finisher controller PC board is disconnected from the buffer tray guide motor (M2) and the harnesses are open circuited. Correct if so.