• Code: CF10
• Description: Communication module SRAM reading failure. [MJ-1101]
• Causes: MJ-1101 Converter PC board Finisher control PC board
  MJ-1101 (When MJ-6103 is installed) Converter PC board Finisher control PC board Hole punch control PC board
• Remedy: MJ-1101 Main power switch Turn OFF the main power switch, then back ON. Setting of the equipment Check if the MJ-1101 is set as the specified finisher on the equipment. (08-4548) Converter PC board • Check the connectors and harnesses between the converter PC board and the finisher controller PC board. • Board check Finisher control PC board Board check
  MJ-1101 (When MJ-6103 is installed) Setting of the equipment Check if the MJ-1101 is set as the specified finisher on the equipment. (08-4548) Converter PC board • Check the connectors and harnesses between the converter PC board and the finisher controller PC board. • Board check Finisher control PC board • Check the connectors and harnesses between the hole punch control PC board and the finisher control PC board. • Board check Hole punch control PC board Board check

• Code: E010
• Description: Jam not reaching the exit sensor: The paper which has passed through the fuser unit does not reach the exit sensor.
• Causes: Exit sensor LGC board Registration roller clutch Registration roller
• Remedy: 1 Open the Automatic duplexing unit. Is there any paper on the transport path? Yes Remove the paper. No 2 2 Is the exit sensor working? (Perform the input check in the test mode: 03- [FAX]ON/[9]/[B]) Yes 3 No • Check if the connector of the exit sensor is disconnected. • Check if the connector CN309 on the LGC board is disconnected. • Check if the connector pins are disconnected and the harnesses are open circuited. • Check if the conductor pattern on the LGC board is short circuited or open circuited. • Replace the exit sensor • Replace the LGC board 3 Is the registration roller clutch working? (Perform the output check in the test mode: 03-108/ 158) Yes 4 No • Check if the connector of the registration roller clutch is disconnected. • Check if the connector CN315 on the LGC board is disconnected. • Check if the connector pins are disconnected and the harnesses are open circuited. • Check if the conductor pattern on the LGC board is short circuited or open circuited. • Replace the registration roller clutch. • Replace the LGC board. 4 Registration roller • Check the registration roller. Replace it if it is worn out.

• Code: E020
• Description: Stop jam at the exit sensor: The trailing edge of the paper does not pass the exit sensor after its leading edge has reached this sensor.
• Causes: Exit sensor LGC board Registration roller clutch Registration roller
• Remedy: 1 Open the Automatic duplexing unit. Is there any paper on the transport path? Yes Remove the paper. No 2 2 Is the exit sensor working? (Perform the input check in the test mode: 03- [FAX]ON/[9]/[B]) Yes 3 No • Check if the connector of the exit sensor is disconnected. • Check if the connector CN309 on the LGC board is disconnected. • Check if the connector pins are disconnected and the harnesses are open circuited. • Check if the conductor pattern on the LGC board is short circuited or open circuited. • Replace the exit sensor • Replace the LGC board 3 Is the registration roller clutch working? (Perform the output check in the test mode: 03-108/ 158) Yes 4 No • Check if the connector of the registration roller clutch is disconnected. • Check if the connector CN315 on the LGC board is disconnected. • Check if the connector pins are disconnected and the harnesses are open circuited. • Check if the conductor pattern on the LGC board is short circuited or open circuited. • Replace the registration roller clutch. • Replace the LGC board. 4 Registration roller • Check the registration roller. Replace it if it is worn out.

• Code: E030
• Description: Power-ON jam: The paper is remaining on the paper transport path when power is turned ON.
• Causes: Sensor Refer to the following table LGC board
• Remedy: 1 Open the cover of the unit/ area whose picture is blinking on the control panel. Is there any paper on the transport path? (Refer to the following table.) Yes Remove the paper. No 2 2 Is the sensor in the jamming area working? (Perform the input check in the test mode: refer to the following table.) Yes 3 No • Check if the connector of the sensor is disconnected. • Check if any of the connectors on the LGC board is disconnected. • Check if the connector pins are disconnected and the harnesses are open circuited. • Check if the conductor pattern on the LGC board is short circuited or open circuited. • Replace the sensor • Replace the LGC board. 3 LGC board • Replace the LGC board.
  Registration area Automatic duplexing unit Registration sensor 03-[FAX]ON/[9]/[A] 1st transport sensor 03-[FAX]OFF/[6]/[A] Exit area Automatic duplexing unit Exit sensor 03-[FAX]ON/[9]/[B] ADU ADU ADU entrance sensor 03-[FAX]OFF/[1]/[D] ADU exit sensor 03-[FAX]OFF/[1]/E] Feeding area (Main unit) Feed cover 2nd transport sensor 03-[FAX]OFF/[7]/[A] LCF LCF side cover LCF feed sensor 03-[FAX]OFF/[4]/[C] PFP PFP side cover PFP upper drawer feed sensor 03-[FAX]OFF/[2]/[B] PFP lower drawer feed sensor 03-[FAX]OFF/[3]/[B] Bridge unit Bridge unit Bridge unit transport sensor-1 03-[FAX]ON/[4]/[G] 03-[FAX]ON/[3]/[G] Bridge unit transport sensor-2 03-[FAX]ON/[4]/[F] 03-[FAX]ON/[3]/[G] JSP JSP cover JSP feed sensor 03-[FAX]ON/[3]/G] OCT OCT cover OCT feed sensor 03-[FAX]ON/[3]/[G]

• Code: E061
• Description: Incorrect paper size setting for upper drawer: The size of paper in the 1st drawer differs from size setting of the equipment.
• Causes:
• Remedy: Paper size If any paper remains in the equipment or drawer, remove it. Match the paper size of the drawer setting and the one in the drawer. * Paper size detection is performed at the first sheet of paper when the drawer is opened or closed, or when the power of the equipment is turned ON.

• Code: E062
• Description: Incorrect paper size setting for lower drawer: The size of paper in the 2nd drawer differs from size setting of the equipment.
• Causes:
• Remedy: Paper size If any paper remains in the equipment or drawer, remove it. Match the paper size of the drawer setting and the one in the drawer. * Paper size detection is performed at the first sheet of paper when the drawer is opened or closed, or when the power of the equipment is turned ON.

• Code: E063
• Description: Incorrect paper size setting for PFP upper drawer: The size of paper in the 3rd drawer differs from size setting of the equipment.
• Causes:
• Remedy: Paper size If any paper remains in the equipment or drawer, remove it. Match the paper size of the drawer setting and the one in the drawer. * Paper size detection is performed at the first sheet of paper when the drawer is opened or closed, or when the power of the equipment is turned ON.

• Code: E064
• Description: Incorrect paper size setting for PFP lower drawer: The size of paper in the 4th drawer differs from size setting of the equipment.
• Causes:
• Remedy: Paper size If any paper remains in the equipment or drawer, remove it. Match the paper size of the drawer setting and the one in the drawer. * Paper size detection is performed at the first sheet of paper when the drawer is opened or closed, or when the power of the equipment is turned ON.