• Code: CBB0
• Description: Rear saddle stapler home position error: The stapler home position detection is abnormally operated and finished. [MJ-1106]
• Causes: Rear saddle stapler clinch unit Saddle control PC board
• Remedy: Rear saddle stapler clinch unit Harness check Saddle control PC board (SDL) • Connector check (CN7) • Board check

• Code: CBC0
• Description: Saddle Stitch Finisher side alignment motor (M15) abnormality: The alignment motor is not rotating or the alignment plate is not working properly. [MJ- 1106]
• Causes: MJ-1106 Side alignment motor (M15) Saddle control PC board (SDL)
• Remedy: MJ-1106 Saddle Unit If there is mechanical problem when the jog is moved, fix the mechanism. Side alignment motor (M15) Harness check Saddle control PC board (SDL) • Connector check (CN7) • Board check
  MJ-1033 Saddle stitch alignment motor (M8) abnormality Check if the electrical continuity of the coil is normal. If electricity is not conducted, replace the motor. Saddle stitch alignment plate home position sensor (S20) abnormality Measure the voltage on pin CN16.12 on the finisher control PC board (FIN). Then check that the measured voltage is 1V or lower when not shielded and within the range of 3.3V±5% when shielded. If the voltage does not fall within the range mentioned, replace the sensor. Faulty cables and connectors Check if the electrical continuity between the connector terminals is normal. If electricity is not conducted, replace the connectors. (Finisher control PC board (FIN): CN6, CN16) Finisher control PC board (FIN) abnormality If the error still occurs after replacing the motor, sensor and connectors, exchange the finisher control PC board (FIN).

• Code: CBE0
• Description: Saddle Stitch Finisher folding motor (M17) abnormality: The folding motor is not rotating or the folding roller is not moving normally. [MJ-1106]
• Causes: Folding motor encoder sensor (S34) Side alignment motor (M15) Saddle control PC board (SDL)
• Remedy: Folding motor encoder sensor (S34) • Sensor check (S34) • Connector check • Harness check Side alignment motor (M15) Harness check Saddle control PC board (SDL) • Connector check (CN11, CN14) • Board check

• Code: CBF0
• Description: Stacker motor (M9) abnormality : The stacker motor is not rotating. [MJ-1033]
• Causes:
• Remedy: Stacker motor (M9) abnormality Check if the electrical continuity of the coil is normal. If electricity is not conducted, replace the motor. Stacker home position sensor (S21) abnormality Measure the voltage on pin CN16.15 on the finisher control PC board (FIN). Then check that the measured voltage is 1V or lower when not shielded and within the range of 3.3V ± 5% when shielded. If the voltage does not fall within the range mentioned, replace the sensor. Faulty cables and connectors Check if the electrical continuity between the connector terminals is normal. If electricity is not conducted, replace the connectors. (Finisher control PC board (FIN): CN6, CN16) Finisher control PC board (FIN) abnormality If the error still occurs after replacing the motor, sensor and connectors, exchange the finisher control PC board (FIN).

• Code: CC01
• Description: A model not supporting the Finisher is connected. Note that this error is recognized in the communication converter and is output.
• Causes:
• Remedy:

• Code: CC02
• Description: Stack exit roller nip home position detection error: The detection of the home position of the stack exit roller nip ends abnormally. [MJ-1032/MJ-1033]
• Causes:
• Remedy: Exit roller nip adjustment motor (M4) abnormality Check if the electrical continuity of the coil is normal. If electricity is not conducted, replace the motor. Exit roller nip home position sensor (S8) abnormality Measure the voltage on TP31 on the finisher control PC board (FIN). Then check that the measured voltage is 1V or lower when not shielded and within the range of 3.3V±5% when shielded. If the voltage does not fall within the range mentioned, replace the sensor. Faulty cables and connectors Check if the electrical continuity between the connector terminals is normal. If electricity is not conducted, replace the connectors. (Finisher control PC board (FIN): CN2, CN9) Finisher control PC board (FIN) abnormality If the error still occurs after replacing the motor, sensor and connectors, exchange the finisher control PC board (FIN).

• Code: CC20
• Description: Saddle communication error [MJ-1106]
• Causes: Interface PC board (I/F) Finisher control PC board (FIN) Saddle control PC board (SDL)
• Remedy: Interface PC board (I/F) • Connector check • Harness check Finisher control PC board (FIN) • Connector check • Harness check Saddle control PC board (SDL) • Connector check • Harness check Interface PC board (I/F) Board check Finisher control PC board (FIN) Board check Saddle control PC board (SDL) Board check Finisher control PC board (FIN) Update the firmware version of the finisher control PC board (FIN). Saddle control PC board (SDL) Update the firmware version of the saddle control PC board (SDL).

• Code: CC21
• Description: The detection of the home position of the saddle stitch 3rd transport roller drive motor ends abnormally.
• Causes:
• Remedy: Saddle stitch 3rd transport roller drive motor (M10) abnormality Check if the electrical continuity of the coil is normal. If electricity is not conducted, replace the motor. Saddle stitch 3rd transport roller home position sensor (S23) abnormality Measure the voltage on TP67 on the finisher control PC board (FIN). Then check that the measured voltage is 1V or lower when not shielded and within the range of 3.3V±5% when shielded. If the voltage does not fall within the range mentioned, replace the sensor. Faulty cables and connectors Check if the electrical continuity between the connector terminals is normal. If electricity is not conducted, replace the connectors. (Finisher control PC board (FIN): CN6, CN16) Finisher control PC board (FIN) abnormality If the error still occurs after replacing the motor, sensor and connectors, exchange the finisher control PC board (FIN).