• Code: E714
• Description: Feed signal reception jam: The feed signal is received even no original exists on the original feeding tray.
• Causes: Original empty sensor RADF board Perform the 05-3210 Roller Pickup roller, feed roller, separation roller
• Remedy: Original empty sensor • Sensor check (Perform the input check: 03-[FAX]ON/[7]/[B]) • Connector check • Harness check RADF board • Connector check (CN74) • Board check Drive unit, Rollers • Gear check • Roller check

• Code: E721
• Description: Jam not reaching the original reading start sensor: The original does not reach the reading start sensor after it has passed the registration sensor (when scanning obverse side) or the reverse sensor (when scanning reverse side).
• Causes: Original reading start sensor RADF board Perform the 05-3210 Roller Registration roller, Read roller
• Remedy: Registration roller Read roller • Cleaning Original reading start sensor • Automatic adjustment (Perform the 05-3210) • Connector check • Harness check RADF board • Connector check (CN75) • Board check Drive unit, Rollers • Gear check • Roller check

• Code: E722
• Description: Jam not reaching the original exit sensor (during scanning): The original which passed the read sensor does not reach the original exit/reverse sensor when it is transported from the scanning section to exit section.
• Causes: Original exit sensor RADF board Perform the 05-3210 Roller
• Remedy: Read roller • Cleaning Original exit sensor • Sensor check (Perform the input check: 03-[FAX]ON/[7]/[E]) • Connector check • Harness check RADF board • Connector check (CN75) • Board check Drive unit, Rollers • Gear check • Roller check

• Code: E724
• Description: Stop jam at the original registration sensor: The trailing edge of the original does not pass the original registration sensor after its leading edge has reached this sensor.
• Causes: Original registration sensor RADF board Perform the 05-3210 Roller
• Remedy: Registration roller • Cleaning Original registration sensor • Sensor check (Perform the input check: 03-[FAX]ON/[7]/[H]) • Connector check • Harness check RADF board • Connector check (CN74) • Board check Drive unit, Rollers • Gear check • Roller check

• Code: E725
• Description: Stop jam at the reading start sensor: The trailing edge of the original does not pass the read sensor after its leading edge has reached this sensor.
• Causes: Original reading start sensor RADF board Perform the 05-3210 Roller Registration roller, Read roller
• Remedy: Registration roller Read roller • Cleaning Original reading start sensor • Automatic adjustment (Perform the 05-3210) • Connector check • Harness check RADF board • Connector check (CN75) • Board check Drive unit, Rollers • Gear check • Roller check

• Code: E726
• Description: Transport/exit signal reception jam during ADF standby status
• Causes:
• Remedy: RADF • Check if there is any paper in the RADF. Remove it if there is. Equipment • Check if there is any paper in the equipment. Remove it if there is. • If a jam still occurs, turn the power OFF and then back ON to check if the equipment operates normally.

• Code: E727
• Description: Jam not reaching the original reading end sensor
• Causes: Original reading end sensor RADF board Perform the 05-3210 Roller Read end roller
• Remedy: RADF • Check the RADF position adjustment. "6.12.1 RADF position adjustment" RADF • Check the Adjustment of the Reversing Automatic Document Feeder (RADF). "6.12 Reversing Automatic Document Feeder (RADF)" Read end roller • Cleaning Original reading end sensor • Sensor check (Perform the input check: 03-[FAX]ON/[5]/[D]) • Connector check • Harness check RADF board • Connector check (CN75) • Board check Drive unit, Rollers • Gear check • Roller check

• Code: E729
• Description: Stop jam at the original reading end sensor
• Causes: Original reading end sensor RADF board Perform the 05-3210 Roller
• Remedy: Read end roller • Cleaning Original reading end sensor • Sensor check (Perform the input check: 03-[FAX]ON/[5]/[D]) • Connector check • Harness check RADF board • Connector check (CN75) • Board check Drive unit, Rollers • Gear check • Roller check