Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Toshiba e-Studio 5540c — Trang 29/44

Code: E731

Description: Stop jam at the original exit/reverse sensor: The trailing edge of the original does not pass the original exit/reverse sensor after its leading edge has reached this sensor.
Causes: Original exit sensor RADF board Perform the 05-3210 Roller Exit roller
Remedy: Exit roller • Cleaning Original exit sensor • Sensor check (Perform the input check: 03-[FAX]ON/[7]/[E]) • Connector check • Harness check RADF board • Connector check (CN75) • Board check Drive unit, Rollers • Gear check • Roller check

Code: E744

Description: Stop jam at the exit/reverse sensor
Causes: Original exit/reverse sensor RADF board Perform the 05-3210 Roller Intermediate transport roller
Remedy: Intermediate transport roller • Cleaning Original exit/reverse sensor • Sensor check (Perform the input check: 03: [FAX]/ON/[5]/[B]) • Connector check • Harness check RADF board • Connector check (CN75) • Board check Drive unit, Rollers • Gear check • Roller check

Code: E745

Description: Jam not reaching the exit reverse sensor
Causes: Original exit reverse sensor RADF board Perform the 05-3210 Roller
Remedy: Intermediate transport roller • Cleaning Original exit/reverse sensor • Sensor check (Perform the input check: 03: [FAX]/ON/[5]/[B]) • Connector check • Harness check RADF board • Connector check (CN75) • Board check Drive unit, Rollers • Gear check • Roller check

Code: E746

Description: Exit/reverse sensor paper remaining jam
Causes: Original exit reverse sensor
Registration sensor
Original width detection sensor-1
Original width detection sensor-2
Original width detection sensor-3
Intermediate transport sensor
Reading end sensor
Exit sensor
RADF board Perform the 05-3210
Roller
Remedy: RADF • Check if there is any paper on each sensor. Remove it if there is. Original exit reverse sensor • Sensor check (Perform the input check: 03: [FAX]/ON/[5]/[B]) • Connector check • Harness check Registration sensor • Sensor check (Perform the input check: 03: [FAX]/ON/[8]/[F]) • Connector check • Harness check Original width detection sensor-1 • Sensor check (Perform the input check: 03: [FAX]/ON/[7]/[F]) • Connector check • Harness check Original width detection sensor-2 • Sensor check (Perform the input check: 03: [FAX]/ON/[8]/[H]) • Connector check • Harness check Original width detection sensor-3 • Sensor check (Perform the input check: 03: [FAX]/ON/[5]/[D]) • Connector check • Harness check Intermediate transport sensor • Sensor check (Perform the input check: 03: [FAX]/ON/[8]/[G]) • Connector check • Harness check Reading end sensor • Sensor check (Perform the input check: 03: [FAX]/ON/[7]/[F]) • Connector check • Harness check Exit sensor • Sensor check (Perform the input check: 03: [FAX]/ON/[7]/[E]) • Connector check • Harness check RADF board • Connector check (CN74, CN75) • Board check Drive unit, Rollers • Gear check • Roller check

Code: E762

Description: Registration sensor paper remaining jam
Causes: Original exit reverse sensor
Registration sensor
Original width detection sensor-1
Original width detection sensor-2
Original width detection sensor-3
Intermediate transport sensor
Reading end sensor
Exit sensor
RADF board Perform the 05-3210
Roller
Remedy: RADF • Check if there is any paper on each sensor. Remove it if there is. Original exit reverse sensor • Sensor check (Perform the input check: 03: [FAX]/ON/[5]/[B]) • Connector check • Harness check Registration sensor • Sensor check (Perform the input check: 03: [FAX]/ON/[8]/[F]) • Connector check • Harness check Original width detection sensor-1 • Sensor check (Perform the input check: 03: [FAX]/ON/[7]/[F]) • Connector check • Harness check Original width detection sensor-2 • Sensor check (Perform the input check: 03: [FAX]/ON/[8]/[H]) • Connector check • Harness check Original width detection sensor-3 • Sensor check (Perform the input check: 03: [FAX]/ON/[5]/[D]) • Connector check • Harness check Intermediate transport sensor • Sensor check (Perform the input check: 03: [FAX]/ON/[8]/[G]) • Connector check • Harness check Reading end sensor • Sensor check (Perform the input check: 03: [FAX]/ON/[7]/[F]) • Connector check • Harness check Exit sensor • Sensor check (Perform the input check: 03: [FAX]/ON/[7]/[E]) • Connector check • Harness check RADF board • Connector check (CN74, CN75) • Board check Drive unit, Rollers • Gear check • Roller check

Code: E770

Description: Original width detection sensor-1 paper remaining jam
Causes: Original exit reverse sensor
Registration sensor
Original width detection sensor-1
Original width detection sensor-2
Original width detection sensor-3
Intermediate transport sensor
Reading end sensor
Exit sensor
RADF board Perform the 05-3210
Roller
Remedy: RADF • Check if there is any paper on each sensor. Remove it if there is. Original exit reverse sensor • Sensor check (Perform the input check: 03: [FAX]/ON/[5]/[B]) • Connector check • Harness check Registration sensor • Sensor check (Perform the input check: 03: [FAX]/ON/[8]/[F]) • Connector check • Harness check Original width detection sensor-1 • Sensor check (Perform the input check: 03: [FAX]/ON/[7]/[F]) • Connector check • Harness check Original width detection sensor-2 • Sensor check (Perform the input check: 03: [FAX]/ON/[8]/[H]) • Connector check • Harness check Original width detection sensor-3 • Sensor check (Perform the input check: 03: [FAX]/ON/[5]/[D]) • Connector check • Harness check Intermediate transport sensor • Sensor check (Perform the input check: 03: [FAX]/ON/[8]/[G]) • Connector check • Harness check Reading end sensor • Sensor check (Perform the input check: 03: [FAX]/ON/[7]/[F]) • Connector check • Harness check Exit sensor • Sensor check (Perform the input check: 03: [FAX]/ON/[7]/[E]) • Connector check • Harness check RADF board • Connector check (CN74, CN75) • Board check Drive unit, Rollers • Gear check • Roller check

Code: E771

Description: Original width detection sensor-2 paper remaining jam
Causes: Original exit reverse sensor
Registration sensor
Original width detection sensor-1
Original width detection sensor-2
Original width detection sensor-3
Intermediate transport sensor
Reading end sensor
Exit sensor
RADF board Perform the 05-3210
Roller
Remedy: RADF • Check if there is any paper on each sensor. Remove it if there is. Original exit reverse sensor • Sensor check (Perform the input check: 03: [FAX]/ON/[5]/[B]) • Connector check • Harness check Registration sensor • Sensor check (Perform the input check: 03: [FAX]/ON/[8]/[F]) • Connector check • Harness check Original width detection sensor-1 • Sensor check (Perform the input check: 03: [FAX]/ON/[7]/[F]) • Connector check • Harness check Original width detection sensor-2 • Sensor check (Perform the input check: 03: [FAX]/ON/[8]/[H]) • Connector check • Harness check Original width detection sensor-3 • Sensor check (Perform the input check: 03: [FAX]/ON/[5]/[D]) • Connector check • Harness check Intermediate transport sensor • Sensor check (Perform the input check: 03: [FAX]/ON/[8]/[G]) • Connector check • Harness check Reading end sensor • Sensor check (Perform the input check: 03: [FAX]/ON/[7]/[F]) • Connector check • Harness check Exit sensor • Sensor check (Perform the input check: 03: [FAX]/ON/[7]/[E]) • Connector check • Harness check RADF board • Connector check (CN74, CN75) • Board check Drive unit, Rollers • Gear check • Roller check

Code: E772

Description: Original width detection sensor-3 paper remaining jam
Causes: Original exit reverse sensor
Registration sensor
Original width detection sensor-1
Original width detection sensor-2
Original width detection sensor-3
Intermediate transport sensor
Reading end sensor
Exit sensor
RADF board Perform the 05-3210
Roller
Remedy: RADF • Check if there is any paper on each sensor. Remove it if there is. Original exit reverse sensor • Sensor check (Perform the input check: 03: [FAX]/ON/[5]/[B]) • Connector check • Harness check Registration sensor • Sensor check (Perform the input check: 03: [FAX]/ON/[8]/[F]) • Connector check • Harness check Original width detection sensor-1 • Sensor check (Perform the input check: 03: [FAX]/ON/[7]/[F]) • Connector check • Harness check Original width detection sensor-2 • Sensor check (Perform the input check: 03: [FAX]/ON/[8]/[H]) • Connector check • Harness check Original width detection sensor-3 • Sensor check (Perform the input check: 03: [FAX]/ON/[5]/[D]) • Connector check • Harness check Intermediate transport sensor • Sensor check (Perform the input check: 03: [FAX]/ON/[8]/[G]) • Connector check • Harness check Reading end sensor • Sensor check (Perform the input check: 03: [FAX]/ON/[7]/[F]) • Connector check • Harness check Exit sensor • Sensor check (Perform the input check: 03: [FAX]/ON/[7]/[E]) • Connector check • Harness check RADF board • Connector check (CN74, CN75) • Board check Drive unit, Rollers • Gear check • Roller check
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie