Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Toshiba e-Studio 6570C — Trang 34/44

Code: EA90

Description: Door open jam: The delivery cover or inlet cover has opened during printing [MJ-1103/1104].
Causes: Delivery cover sensor (PI3) Inlet cover sensor (PI9) Saddle stitcher controller board
Remedy: Finisher, saddle stitcher • Check if there is any paper in the finisher, saddle stitcher or the on the transport path of the equipment. Remove it if there is. Delivery cover sensor (PI3) • Sensor check • Connector check • Harness check Inlet cover sensor (PI9) • Sensor check • Connector check • Harness check Saddle stitcher controller board • Connector check(J10, J11) • Board check

Code: EAA0

Description: Power-ON jam: Paper exists at No.1 paper sensor, No. 2 paper sensor, No.3 paper sensor, vertical path paper sensor or delivery sensor when power is turned ON. [MJ-1103/1104]
Causes: No. 1 paper sensor (PI18) No. 2 paper sensor (PI19) No. 3 paper sensor (PI20) Vertical path paper sensor (PI17) Delivery sensor (PI11) Saddle stitcher controller board
Remedy: Finisher, saddle stitcher • Check if there is any paper in the finisher, saddle stitcher or the on the transport path of the equipment. Remove it if there is. No. 1 paper sensor (PI18) • Sensor check • Connector check • Harness check No. 2 paper sensor (PI19) • Sensor check • Connector check • Harness check No. 3 paper sensor (PI20) • Sensor check • Connector check • Harness check Vertical path paper sensor (PI17) • Sensor check • Connector check • Harness check Delivery sensor (PI11) • Sensor check • Connector check • Harness check Saddle stitcher controller board • Connector check(J10, J13) • Board check

Code: EAB0

Description: Transport stop jam: The paper which passed through the inlet sensor does not reach or pass No.1 paper sensor, No. 2 paper sensor, No.3 paper sensor or delivery sensor. [MJ-1103/1104]
Causes: No. 1 paper sensor (PI18) No. 2 paper sensor (PI19) No. 3 paper sensor (PI20) Delivery sensor (PI11) Saddle stitcher controller board
Remedy: Finisher, saddle stitcher • Check if there is any paper in the finisher, saddle stitcher or the on the transport path of the equipment. Remove it if there is. No. 1 paper sensor (PI18) • Sensor check • Connector check • Harness check No. 2 paper sensor (PI19) • Sensor check • Connector check • Harness check No. 3 paper sensor (PI20) • Sensor check • Connector check • Harness check Delivery sensor (PI11) • Sensor check • Connector check • Harness check Saddle stitcher controller board • Connector check(J9, J10) • Board check

Code: EAB1

Description: Short paper jam (Saddle Stitch Finisher)
Causes: Feeding sensor (S22) Junction box paper detection sensor (S26) Transport path-2 (S27) Transport path-3 (S28) Ejecting roller (S29) Interface PC board (I/F) Saddle stitcher controller board Finisher controller board
Remedy: Finisher, saddle stitcher • Check if there is any paper in the finisher, saddle stitcher or the on the transport path of the equipment. Remove it if there is. • Use paper accepted in the specifications. Feeding sensor (S22) • Sensor check • Connector check • Harness check Junction box paper detection sensor (S26) • Sensor check • Connector check • Harness check Transport path-2 (S27) • Sensor check • Connector check • Harness check Transport path-3 (S28) • Sensor check • Connector check • Harness check Ejecting roller (S29) • Sensor check • Connector check • Harness check Interface PC board (I/F) • Connector check(CN8) • Board check Saddle stitcher controller board • Connector check(CN20) • Board check Finisher controller board • Connector check • Board check

Code: EAD0

Description: Print end command time-out jam: The printing has not finished normally because of the communication error between the SYS board and LGC board at the end of printing.
Causes: SYS board LGC board
Remedy: Power • Check if the error is cleared by turning the power OFF and then back ON. SYS board • Connector check • Board check LGC board • Connector check • Board check

Code: EAE0

Description: Receiving time time-out jam: The printing has been interrupted because of the communication error between the equipment and finisher when the paper is transported from the equipment to the finisher.
Causes: Finisher controller board
Remedy: Finisher • Is the finisher working? • Check if the voltage (24V) is being supplied to the finisher. Finisher controller board • Connector check • Board check

Code: EB30

Description: Ready time time-out jam: The equipment judges that the paper transport to the finisher is disabled because of the communication error between the equipment and finisher at the start of printing.
Causes: Finisher controller board LGC board
Remedy: Finisher • Check if there is any paper in the equipment. Remove it if there is. Finisher controller board • Connector check • Board check LGC board • Connector check • Board check

Code: EB50

Description: Paper remaining on the transport path: The multiple feeding of preceding paper caused the misfeeding of upcoming paper.
Causes: 1st drawer feed sensor Bypass feed sensor ADU exit sensor Registration sensor 1st drawer feed sensor 2nd drawer feed sensor ADU board LGC board Rollers
Remedy: 1st drawer feed sensor (When the paper is fed from the 1st drawer:) • Sensor check (Perform the input check: 03-[SCAN]ON/[1]/[H]) • Connector check • Harness check Bypass feed sensor (When the paper is fed from the bypass feed unit:) • Sensor check (Perform the input check: 03-[SCAN]ON/[3]/[A]) • Connector check • Harness check ADU exit sensor (When the paper is fed from the ADU:) • Sensor check (Perform the input check: 03-[SCAN]ON/[3]/[G]) • Connector check • Harness check Registration sensor (When the paper is fed from the ADU:) • Sensor check (Perform the input check: 03-[ALL]OFF/[4]/[B], 03- [COPY]ON/[5]/[H]) • Connector check • Harness check 1st drawer feed sensor (When the paper is fed from any of the 2nd drawer, PFP or LCF:) • Sensor check (Perform the input check: 03-[SCAN]ON/[1]/[H]) • Connector check • Harness check 2nd drawer feed sensor (When the paper is fed from any of the 2nd drawer, PFP or LCF:) • Sensor check (Perform the input check: 03-[SCAN]ON/[1]/[G]) • Connector check • Harness check ADU board • Connector check (CN211, CN213) • Board check LGC board • Connector check (CN337, CN338, CN347, CN348) • Board check Drive unit, Rollers • Gear check • Roller check
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie