Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Toshiba e-Studio 6570C — Trang 33/44

Code: EA28

Description: Paper transport jam (assisting arm operation delay): [MJ-1103/1104]
Causes: Assist arm motor (M10) Finisher controller board
Remedy: Finisher • Check if there is any paper in the finisher or on the transport path of the equipment and remove it if there is. Paper holding cam • Is there any mechanical problem when the paper holding cam is rotated? Assist arm motor (M10) • Motor check • Connector check • Harness check Finisher controller board • Connector check(CN13) • Board check

Code: EA29

Description: Paper transport jam (stack transport delay): [MJ1103/1104]
Causes: Buffer tray guide motor (M2) Finisher controller board
Remedy: Finisher • Check if there is any paper in the finisher or on the transport path of the equipment and remove it if there is. Buffer tray • Is there any mechanical problem when the buffer tray guide is opened and closed while the buffer roller is kept raised? Buffer tray guide motor (M2) • Motor check • Connector check • Harness check Finisher controller board • Connector check(CN11) • Board check

Code: EA31

Description: Transport path paper remaining jam: The paper which has passed through the inlet sensor does not reach the transport sensor. [MJ-1103/1104]
Causes: Transport sensor (S2) Finisher controller board
Remedy: Finisher • Check if there is any paper in the finisher or on the transport path of the equipment and remove it if there is. Transport sensor (S2) • Sensor check • Connector check • Harness check Finisher controller board • Connector check(CN11) • Board check

Code: EA32

Description: Exit paper remaining jam: The paper is remaining on the finishing tray when the power is turned ON. [MJ-1103/1104]
Causes: Finishing tray paper detection sensor (S12) Finisher controller board
Remedy: Finisher • Check if there is any paper in the finisher or on the transport path of the equipment and remove it if there is. Finishing tray paper detection sensor (S12) • Sensor check • Connector check • Harness check Finisher controller board • Connector check(CN11) • Board check

Code: EA40

Description: Door open jam: The upper/front cover of the finisher section or the upper/ front door of the puncher section has opened during printing. [MJ-1103/1104] Cover open error: The front cover or stationary tray cover is opened during paper transport. [MJ-1103/1104]
Causes: Front cover switch (SW1) Stationary tray opening/closing switch (SW2) Finisher controller board
Remedy: Cover • Close the front cover or the stationary tray cover if they are opened. Front cover switch (SW1) • Sensor check • Connector check • Harness check Stationary tray opening/closing switch (SW2) • Sensor check • Connector check • Harness check Finisher controller board • Connector check(CN16) • Board check

Code: EA50

Description: Stapling jam: Stapling is not performed properly. [MJ-1103/1104]
Causes: Stapler interference sensor (S11) Finisher controller board
Remedy: Finisher • Check if there is any paper in the finisher or on the transport path of the equipment and remove it if there is. • Is the jam cleared by taking off the staple cartridge from the finisher and removing the staple sheet slid from the staple case? Stapler interference sensor (S11) • Sensor check • Connector check • Harness check Finisher controller board • Connector check(CN2) • Board check

Code: EA60

Description: Early arrival jam: The inlet sensor detects the paper earlier than a specified timing. [MJ-1103/1104]
Causes: Entrance sensor (S1) Finisher controller board
Remedy: Finisher • Check if there is any paper in the finisher or on the transport path of the equipment and remove it if there is. Entrance sensor (S1) • Sensor check • Connector check • Harness check Finisher controller board • Connector check(CN7) • Board check

Code: EA70

Description: Stack exit belt home position error: The stack exit belt is not at the home position. [MJ-1103/1104]
Causes: Stack belt exit home position sensor (S9) Stack transport motor (M5) Finisher controller board
Remedy: Stack belt exit home position sensor (S9) • Sensor check • Connector check • Harness check Stack transport motor (M5) • Motor check • Connector check • Harness check Finisher controller board • Connector check(CN10, CN11) • Board check Upper surface detection sensor • Refer to CB31
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie