Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Xerox Phaser 7800 — Trang 21/58

Code: 313.211

Description: Booklet Staple Move Home Sensor Off
Remedy: Procedure Execute dc330 Component Control [013-143], Booklet Staple Move Home Sensor. Move the Booklet Staplers to block and unblock the Sensor (PL 23.18 Item 13). The display changes. Y↓ N→Check the wire between J8897 pin 2 and P/J8991 pin 2 for an open or short circuit, or a loose or damaged connector. The wire is OK. Y↓ N→Repair/reconnect as required. Measure the voltage between P/J8991, pins 3 and 1 on the Booklet PWB (Booklet Staple Positioning). The voltage is approx. +5VDC. Y↓ N→Replace the Booklet PWB. Measure the voltage between P/J8991 pin 2 on the Booklet PWB and GND (Booklet Staple Positioning). Actuate the Booklet Staple Move Home Sensor. The voltage changes. Y↓ N→Replace the Booklet Staple Move Home Sensor (PL 23.18 Item 13). Replace the Booklet PWB. Alternately execute dc330 Component Control [013-028], Stapler Move Motor In and [013- 029], Stapler Move Motor Out. The Stapler Move Motor moves. Y↓ N→Check the wires between P/J8992 pins 1~6 on the Booklet PWB and P/J8906 on the Booklet Stapler Move Motor (Booklet Staple Positioning) for an open or short circuit, or loose or damaged connectors. The wires are OK. Y↓ N→Repair/replace as required. Monitor the voltage at P/J8994, pin 3 (Booklet Staple Positioning). Alternately execute dc330 Component Control [013-028], Stapler Move Motor In and [013-029], Stapler Move Motor Out. An AC clock pulse is detected. Y↓ N→Check the wire between P/J8994, pin 3 and P/J8995 pin 4. If the wire is OK, replace the Finisher PWB. Replace the Booklet Stapler Move Motor. If the problem persists, replace the Booklet PWB. Go to Booklet Staple Positioning and check for an intermittent circuit.

Code: 313.212

Description: Booklet Staple Move Position Sensor On Fault
Remedy: Execute dc330 Component Control [013-144], Booklet Staple Move Position Sensor. Move the Booklet Stapler to block and unblock the Sensor (PL 23.18 Item 13). The display changes. Y↓ N→Check the wire between J8898 pin 2 and P/J8991 pin 5; and the wire between J8894, pin 5 and P/J8995 pin 5 for an open or short circuit, or a loose or damaged connector. The wires are OK. Y↓ N→Repair/reconnect as required. Measure the voltage between P/J8991, pins 6 and 4 on the Booklet PWB (Booklet Staple Positioning). The voltage is approx. +5VDC. Y↓ N→Replace the Booklet PWB. Measure the voltage between P/J8991 pin 5 on the Booklet PWB and GND (Booklet Staple Positioning). Actuate the Booklet Staple Move Position Sensor. The voltage changes. Y↓ N→Replace the Booklet Staple Move Position Sensor (PL 23.18 Item 13). Measure the voltage between J8985 pin 5 on the Finisher PWB and GND (Booklet Staple Positioning). Actuate the Booklet Staple Move Position Sensor. The voltage changes. Y↓ N→Replace the Booklet PWB. If the problem persists, replace the Finisher PWB. Replace the Finisher PWB. Alternately execute dc330 Component Control [013-028], Stapler Move Motor In and [013- 029], Stapler Move Motor Out. The Stapler Move Motor moves. Y↓ N→Check the wires between P/J8992 pins 1~6 on the Booklet PWB and P/J8906 on the Booklet Stapler Move Motor (Booklet Staple Positioning) for an open or short circuit, or loose or damaged connectors. The wires are OK. Y↓ N→Repair/replace as required. Monitor the voltage at J8894, pin 3 (Booklet Staple Positioning). Alternately execute dc330 Component Control [013-028], Stapler Move Motor In and [013-029], Stapler Move Motor Out. An AC clock pulse is detected. Y↓ N→Check the wire between J8894, pin 3 and P/J8995 pin 4. If the wire is OK, replace the Finisher PWB. Replace the Booklet Stapler Move Motor. If the problem persists, replace the Booklet PWB. Go to Booklet Staple Positioning and check for an intermittent circuit.

Code: 313.213

Description: Booklet Staple Move Position Sensor Off Fault.
Remedy: Execute dc330 Component Control [013-144], Booklet Staple Move Position Sensor. Move the Booklet Stapler to block and unblock the Sensor (PL 23.18 Item 13). The display changes. Y↓ N→Check the wire between J8898 pin 2 and P/J8991 pin 5; and the wire between P/J8994, pin 5 and J8985 pin 5 for an open or short circuit, or a loose or damaged connector. The wires are OK. Y↓ N→Repair/reconnect as required. Measure the voltage between P/J8991, pins 6 and 4 on the Booklet PWB (Booklet Staple Positioning). The voltage is approx. +5VDC. Y↓ N→Replace the Booklet PWB. Measure the voltage between P/J8991 pin 5 on the Booklet PWB and GND (Booklet Staple Positioning). Actuate the Booklet Staple Move Position Sensor. The voltage changes. Y↓ N→Replace the Booklet Staple Move Position Sensor (PL 23.18 Item 13). Measure the voltage between P8985 pin 5 on the Finisher PWB and GND (Booklet Staple Positioning). Actuate the Booklet Staple Move Position Sensor. The voltage changes. Y↓ N→Replace the Booklet PWB. If the problem persists, replace the Finisher PWB. Replace the Finisher PWB. Alternately execute dc330 Component Control [013-028], Stapler Move Motor In and [013- 029], Stapler Move Motor Out. The Stapler Move Motor moves. Y↓ N→Check the wires between P/J8992 pins 1~6 on the Booklet PWB and P/J8906 on the Booklet Stapler Move Motor (Booklet Staple Positioning) for an open or short circuit, or loose or damaged connectors. The wires are OK. Y↓ N→Repair/replace as required. Monitor the voltage at J8894, pin 3 (Booklet Staple Positioning). Alternately execute dc330 Component Control [013-028], Stapler Move Motor In and [013-029], Stapler Move Motor Out. An AC clock pulse is detected. Y↓ N→Check the wire between J8894, pin 3 and P8985 pin 4. If the wire is OK, replace the Finisher PWB. Replace the Booklet Stapler Move Motor. If the problem persists, replace the Booklet PWB. Go to Booklet Staple Positioning and check for an intermittent circuit.

Code: 313.220

Description: Booklet Creaser Detect Fault.
Remedy: Execute dc330 Component Control [013-160], Creaser Detected. The display is ‘Low.’ Y↓ N→There is less than 1 VDC at P/J8990 pin 4. Y↓ N→Check the wires between P/J8990 pins 4 and 5. Make sure that P/J8903 is securely fastened. Replace the Finisher PWB. Go to Folder Control and check for an intermittent circuit.

Code: 313.306

Description: Booklet Safety Switches Open
Remedy: There is +24 VDC between P/J8993 pin 3 on the Booklet PWB and GND. Y↓ N→There is +24 VDC between P/J8993 pin 6 on the Booklet PWB and GND. Y↓ N→Go to the 313.307 (SB) RAP. Go to Booklet Interlock Switching and check the circuit through the Booklet Safety Switches (PL 23.21). Replace the Booklet PWB.

Code: 313.307

Description: Booklet Cover Open.
Remedy: There is +24 VDC between P/J8993 pin 5 on the Booklet PWB and GND. Y↓ N→Go to Booklet Interlock Switching and check the circuit from P/J8993 to and from J8899 on the Booklet Stapler Cover Switch (PL 23.21). Replace the Booklet PWB.

Code: 313.902

Description: Paper Remains at Booklet Compiler No Paper Sensor
Remedy: Go to 312.266 (C) to troubleshoot the fault.

Code: 313.903

Description: Paper Remains at Booklet Folder Roll Exit Sensor
Remedy: Go to 312.115 (C) and/or 312.180 (C) to troubleshoot the Fault.
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie