Description: DADF Pre Regi Sensor Off Jam on Inverting After the DADF Feed Motor started the reverse rotation at Invert operation, the DADF Pre Regi Sensor did not turn OFF within the specified time.
Remedy: Check the following: • Transportation failure due to foreign substance on the document path. • The surface of the Exit Roll, Takeaway Roll, Regi Roll, and Out Roll for foreign substances. • The surface of the Exit Roll, Takeaway Roll, Regi Roll, and Out Roll for wear. • The DADF Pre Regi Sensor (Input Check [005-206]) for operation failure. (PL 56.14) • The DADF Feed Motor (Output Check [005-048/008] (CCW/CW)) for operation failure. (PL 56.6) • The Exit Pinch Roll for operation failure (including for the operation failure of the Exit Nip Release Solenoid (Output Check [005-072])). (PL 56.7) • The Drive Gear for wear and damage. If no problem is found, replace the DADF PWB. (PL 56.2)
Description: Size Mismatch Jam on No Mix-Size The 2nd sheet or later of the document was detected to be of a different size conpared to the 1st sheet (the length of the document's 2nd sheet or later in SS direction is longer).
Remedy: 1. Check the size of the document that was fed by the User. 2. If the error is not cleared, check the following: • The DADF Pre Regi Sensor (Input Check [005-206]) for operation failure. (PL 56.14) • The Document Tray Size Sensor 1/2 (Input Check [005-221/222]) for operation failure. (PL 56.11) 3. If no problem is found, replace the DADF PWB. (PL 56.2)
Description: Too Short Size Jam/ Too Long Size Jam [Too Short Size Jam] It was detected that the document length in Slow Scan direction is shorter than the specifications (Simpex: 85 mm, Duplex: 110 mm). [Too Long Size Jam] It was detected that the document length in Slow Scan direction is at the specifications (Simpex: 1275 mm, Duplex: 480.1 mm) or longer.
Remedy: Check the size of the document that was fed by the user. If it is within the permitted length for DADF transport, check the following: • The DADF Pre Regi Sensor (Input Check [005-206]) for operation failure. (PL 56.14) • The Document Tray Size Sensor 1/2 (Input Check [005-221/222]) for operation failure. (PL 56.11) If no problem is found, replace the DADF PWB. (PL 56.2)
Description: DADF RAM Test Fail/ DADF EEPROM Fail [DADF RAM Test Fail] The DADF PWB RAM failed during the Read/Write operation. (At Power ON) [DADF EEPROM Fail] Write failure to DADF EEPROM or communication failure with EEPROM was detected.
Remedy: 1. Turn the power OFF and ON. 2. If the problem persists, replace the DADF PWB. (PL 56.2)
Description: DADF Feeder Cover Interlock Open The DADF Feeder Cover Interlock Switch was opened during DADF operation.
Remedy: 1. Check the DADF Feeder Cover for mismatch. 2. Check the DADF Feeder Cover Interlock Switch (Input Check [005-212]) for operation failure. (PL 56.6) 3. If no problem is found, replace the DADF PWB. (PL 56.2)
Description: DADF Download Flash Write Error Failed to write into the Flash ROM during DAFD Download
Remedy: 1. Turn the power OFF and ON. • If the device starts up normally Check the FW Version of the DADF. If the FW Version is not the expected version, turn OFF the power, start up the device in Download Mode, and then try to download again. If the problem persists, replace the DADF PWB. (PL 56.2) • If the device does not start up normally Turn OFF the power and start up the device in Download Mode. If the device can start up in Download Mode, try to download the FW again. If the problem persists, replace the DADF PWB. (PL 56.2) If it cannot start up in Download Mode, replace the DADF PWB. (PL 56.2)
Nhận ưu đãi sớm nhất khi chương trình diễn ra
Đăng ký nhận bản tin
Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này.
Chính sách cookie
Những cookie này là cần thiết để trang web hoạt động đúng cách.
Những cookie này giúp chúng tôi hiểu cách khách truy cập tương tác với trang web.
Những cookie này được sử dụng để cung cấp quảng cáo cá nhân hóa.