Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Xerox WorkCentre 5024 — Trang 7/18

Code: 024-946

Description: Tray 1 Unknown Paper Size One of the following errors was detected. • During Copy Job and Diag Job, Tray 1 was selected but the paper guides in Tray 1 are in a configuration that is not supported by the System. • During Copy Job and Diag Job, Tray 1 was selected but it has been pulled out.
Remedy: Press [Stop] on the UI Panel and either install Tray 1 or check the position of the paper guides and load the correct paper. NOTE: When performing the operation again, the same Fault will occur if the user had proceeded without changing the settings. If the problem persists, check the following: • The Tray 1 paper guide mechanism for damage and foreign substances. • The Tray 1 Paper Size Switch for damage, improper installation, and Actuator operation failure. • Tray 1 Paper Size Switch: Analog Monitor [072-050]/Input Check [072-114] (PL 9.1) • The connection between the Tray 1 Paper Size Switch J109 and the ESS/MCU PWB J412 for open circuit, short circuit, and poor contact. If no problems are found, replace the ESS/MCU PWB (PL 18.3).

Code: 024-947

Description: Tray 2 Unknown Paper Size One of the following errors was detected. • During Copy Job and Diag Job, Tray 2 was selected but the paper guides in Tray 2 are in a configuration that is not supported by the System. • During Copy Job and Diag Job, Tray 2 was selected but it has been pulled out.
Remedy: Press [Stop] on the UI Panel and either install Tray 2 or check the position of the paper guides and load the correct paper. NOTE: When performing the operation again, the same Fault will occur if the user had proceeded without changing the settings. If the problem persists, check the following: • The Tray 2 paper guide mechanism for damage and foreign substances. • The Tray 2 Paper Size Switch for damage, improper installation, and Actuator operation failure. • Tray 2 Paper Size Switch: Analog Monitor [072-051]/Input Check [072-107] (PL 10.1) • The connection between the Tray 2 Paper Size Switch J820C and the STM PWB J548C for open circuit, short circuit, and poor contact. If no problems are found, replace the following parts in sequence: • STM PWB (PL 10.6) • ESS/MCU PWB (PL 18.3)

Code: 024-948

Description: Tray 3 Unknown Paper Size One of the following errors was detected. • During Copy Job and Diag Job, Tray 3 was selected but the paper guides in Tray 3 are in a configuration that is not supported by the System. • During Copy Job and Diag Job, Tray 3 was selected but it has been pulled out.
Remedy: Press [Stop] on the UI Panel and either install Tray 3 or check the position of the paper guides and load the correct paper. NOTE: When performing the operation again, the same Fault will occur if the user had proceeded without changing the settings. If the problem persists, check the following: • The Tray 3 paper guide mechanism for damage and foreign substances. • The Tray 3 Paper Size Switch for damage, improper installation, and Actuator operation failure. • Tray 3 Paper Size Switch: Analog Monitor [072-052]/Input Check [072-110] (PL 11.1) • The connection between the Tray 3 Paper Size Switch J820 and the 2TM PWB J548 for open circuit, short circuit, and poor contact. If no problems are found, replace the following parts in sequence: • 2TM PWB (PL 11.6) • ESS/MCU PWB (PL 18.3)

Code: 024-949

Description: Tray 4 Unknown Paper Size One of the following errors was detected. • During Copy Job and Diag Job, Tray 4 was selected but the paper guides in Tray 4 are in a configuration that is not supported by the System. • During Copy Job and Diag Job, Tray 4 was selected but it has been pulled out.
Remedy: Press [Stop] on the UI Panel and either install Tray 4 or check the position of the paper guides and load the correct paper. NOTE: When performing the operation again, the same Fault will occur if the user had proceeded without changing the settings. If the problem persists, check the following: • The Tray 4 paper guide mechanism for damage and foreign substances. • The Tray 4 Paper Size Switch for damage, improper installation, and Actuator operation failure. • Tray 4 Paper Size Switch: Analog Monitor [072-053]/Input Check [072-113] (PL 11.1) • The connection between the Tray 4 Paper Size Switch J824 and the 2TM PWB J548 for open circuit, short circuit, and poor contact. If no problems are found, replace the following parts in sequence: • 2TM PWB (PL 11.6) • ESS/MCU PWB (PL 18.3)

Code: 024-950

Description: Tray 1 No Paper Any of the following was detected: • The paper in the Tray 1 has ran out. (When the ATS function of Tray 1 is disabled) • Although the paper in the Tray 1 was detected to have ran out, paper is not supplied from another Tray. (When the ATS function of Tray 1 is enabled)
Remedy: 1. Load paper into the Tray 1. (If this had occurred during ATS of Tray 1 or Tray 2, load paper with the same settings as for the applicable Tray into other than MSI.) 2. If the problem persists, check the following: • The paper supply mechanism of the applicable Tray for damage and foreign substances. • The No Paper Sensor of the Tray 1 (Input Check [072-100]) for operation failure. (PL 9.1) • The No Paper Sensor of the Tray 1 for contamination, improper installation, and Actuator operation failure. 3. If no problem is found, replace the following parts: • ESS/MCU PWB (PL 18.3)

Code: 024-951

Description: Tray 2 No Paper Any of the following was detected: • The paper in the Tray 2 has ran out. (When the ATS function of Tray 2 is disabled) • Although the paper in the Tray 2 was detected to have ran out, paper is not supplied from another Tray. (When the ATS function of Tray 2 is enabled)
Remedy: 1. Load paper into the Tray 2. (If this had occurred during ATS of Tray 1 or Tray 2, load paper with the same settings as for the applicable Tray into other than MSI.) 2. If the problem persists, check the following: • The paper supply mechanism of the applicable Tray for damage and foreign substances. • The No Paper Sensor of the Tray 2 (Input Check [072-101]) for operation failure. (PL 10.3) • The No Paper Sensor of the Tray 2 for contamination, improper installation, and Actuator operation failure. 3. If no problem is found, replace the following parts: • ESS/MCU PWB (PL 18.3) • STM PWB (Tray 2) (PL 10.6)

Code: 024-952

Description: Tray 3 No Paper One of the following errors was detected. However, this is not detected until the paper is about to be fed. • During Copy Job or Print Job, Tray 3 was selected but Tray 3 has run out of paper and the ATS function for Tray 3 is disabled. This also includes the cases where Tray 3 was selected by the System Controller due to APS result. • During Copy Job or Print Job, Tray 3 was selected by the System due to APS result but it was detected that Tray 3 has run out of paper and the machine is unable to ATS to other Trays.
Remedy: Perform any of the following: • Press [Stop] on the UI Panel. • Load paper into Tray 3. • If this had occurred during ATS, load paper with the same settings as for Tray 3 into other than MSI. If the problem persists, check the following: • The Tray 3 paper supply mechanism for damage and foreign substances. • The Tray 3 No Paper Sensor for contamination, improper installation, and Actuator operation failure. • Tray 3 No Paper Sensor: Input Check [072-102] (PL 11.3) • The connection between the Tray 3 No Paper Sensor J102B and the 2TM PWB J549 for open circuit, short circuit, and poor contact. If no problems are found, replace the following parts in sequence: • 2TM PWB (PL 11.6) • ESS/MCU PWB (PL 18.3)

Code: 024-953

Description: Tray 4 No Paper One of the following errors was detected. However, this is not detected until the paper is about to be fed. • During Copy Job or Print Job, Tray 4 was selected but Tray 4 has run out of paper and the ATS function for Tray 4 is disabled. This also includes the cases where Tray 4 was selected by the System Controller due to APS result. • During Copy Job or Print Job, Tray 4 was selected by the System due to APS result but it was detected that Tray 4 has run out of paper and the machine is unable to ATS to other Trays.
Remedy: Perform any of the following: • Press [Stop] on the UI Panel. • Load paper into Tray 4. • If this had occurred during ATS, load paper with the same settings as for Tray 4 into other than MSI. If the problem persists, check the following: • The Tray 4 paper supply mechanism for damage and foreign substances. • The Tray 4 No Paper Sensor for contamination, improper installation, and Actuator operation failure. • Tray 4 No Paper Sensor: Input Check [072-103] (PL 11.3) • The connection between the Tray 4 No Paper Sensor J102A and the 2TM PWB J549 for open circuit, short circuit, and poor contact. If no problems are found, replace the following parts in sequence: • 2TM PWB (PL 11.6) • ESS/MCU PWB (PL 18.3)
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie