Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Xerox WorkCentre 5845 — Trang 8/28

Code: 311-066-00-171, 311-384-00-171

Description: HVF BM Tamper Failure RAP 311-066-00-171 The HVF tamper has failed to clear the home sensor. 311-384-00-171 The HVF tamper is not at the home sensor.
Remedy: Enter dC330 code 011-384 Actuate the BM tamper 1 home sensor, Q11-384. The display changes. Y↓N→Go to Flag 1. Check Q11-384. Refer to: • GP 11, How to Check a Sensor. • P/J556, BM PWB. • 311A-171 HVF Power Distribution RAP. Install new components as necessary: • BM PWB, PL 11.166 Item 10. • BM tamper 1 home sensor, PL 11.162 Item 1. Enter dC330 code 011-066, to run the BM tamper 1 motor, MOT11-066. MOT11-066 runs. Y↓N→Go to Flag 2 and Flag 3. Check MOT11-066. Refer to: • GP 10 How to Check a Motor. • P/J554, BM PWB. • 311A-171 HVF Power Distribution RAP. Install new components as necessary: • BM PWB, PL 11.166 Item 10. • BM tamper 1 motor, PL 11.162 Item 3. The fault may be intermittent, check for damaged wiring or bad connectors. If necessary install new components: • BM tamper 1 home sensor, PL 11.162 Item 1. • BM tamper 1 motor, PL 11.162 Item 3. • BM PWB, PL 11.166 Item 10.

Code: 311-083-00-171, 311-440-00-171 ... 311-443-00-171

Description: Paper Pusher RAP 311-083-00-171 The paper pusher motor has stalled. 311-440-00-171 The paper pusher has failed to return to the home, (upper) position. 311-441-00-171 The paper pusher has failed to move from the home, (upper) position. 311-442-00-171 The paper pusher has failed to return to the away, (lower) position. 311-443-00-171 The paper pusher has failed to move from the away, (lower) position.
Remedy: shows the location of the components. Enter dC330 code 011-083 to run the paper pusher motor, MOT11-083. MOT11-083 runs. Y↓N→Go to Flag 2. Check MOT11-083. Refer to: • GP 10 How to Check a Motor. • P/J202, HVF Control PWB • 311A-171 HVF Power Distribution RAP Install new components as necessary: • Paper pusher motor, PL 11.145 Item 13. • HVF control PWB, PL 11.157 Item 2 Go to Flag 4. Check the stapler gate safety switch, S11-365. Refer to: • GP 13 How to check a switch • P/J304, HVF Control PWB • 311A-171 HVF Power Distribution RAP S11-365 is good. Y↓N→Install new components as necessary: • Sensor assembly, PL 11.145 Item 22. • HVF control PWB PL 11.157 Item 2. Enter dC330 code 011-171. Manually operate the paper pusher upper sensor, Q11-171, The display changes. Y↓N→Go to Flag 1. Check Q11-171. Refer to: • GP 11 How to Check a Sensor. • P/J201, HVF Control PWB • 311A-171 HVF Power Distribution RAP Install new components as necessary: • Paper pusher upper sensor, PL 11.145 Item 16. • HVF control PWB PL 11.157 Item 2 Enter dC330 code 011-173. Manually actuate the paper pusher lower sensor, Q11-173. The display changes. Y↓N→Go to Flag 3. Check Q11-173. Refer to: • GP 11 How to Check a Sensor. • P/J201, HVF Control PWB • 311A-171 HVF Power Distribution RAP Install new components as necessary: • Paper pusher lower sensor, PL 11.145 Item 16. • HVF control PWB PL 11.157 Item 2. The fault may be intermittent, check for damaged wiring or bad connectors. If necessary install new components: • Paper pusher upper sensor, PL 11.145 Item 22. • Paper pusher lower sensor, PL 11.145 Item 22. • Paper pusher motor, PL 11.145 Item 13. • HVF control PWB, PL 11.157 Item 2. • Stapler gate safety switch, PL 11.145 Item 17.

Code: 311-100-00-110

Description: 2K LCSS Paper Entry RAP 311-100-00-110 The leading edge of the sheet is late to the entry sensor.
Remedy: Lower the paper entry guide assembly, PL 11.14 Item 8, to access the entry sensor. Enter dC330 code 011-100. Actuate the entry sensor, Q11-100. The display changes. Y↓N→Go to Flag 1. Check Q11-100. Refer to: • 311G-110 2K LCSS PWB Damage RAP. • GP 11, How to Check a Sensor. • P/J304, 2K LCSS PWB. • 311D-110 2K LCSS Power Distribution RAP. Install new components as necessary: • Entry sensor, PL 11.24 Item 3. • 2K LCSS PWB, PL 11.26 Item 1. Perform SCP 5 Final Actions.

Code: 311-100-00-120

Description: 1K LCSS Paper Entry RAP 311-100-00-110 The leading edge of the sheet is late to the entry sensor Q11-100.
Remedy: Check the following: • 1K LCSS PWB DIP switch settings, refer to the 311E-120 1K LCSS PWB DIP Switch Settings RAP. • Ensure the paper tray guides are set to the correct position for the size of paper in the tray. • Check the input guide for damage or wear that could cause paper to jam. • Paper jam in the machine to 1K LCSS paper path. • IOT exit path and feed rolls. • Feeding performance from a paper tray loaded with a new ream of paper.
. Lower the paper entry guide assembly, PL 11.110 Item 8, to access the entry sensor. Enter dC330, code 011-100 entry sensor, Q11-100. Actuate Q11-100. The display changes. Y↓N→Go to Flag 1. Check Q11-100. Refer to: • 311F-120 1K LCSS PWB Damage RAP. • GP 11 How to Check a Sensor. • P/J8, 1K LCSS PWB • 311C-120 1K LCSS Power Distribution RAP. Install new components as necessary: • Entry sensor, PL 11.122 Item 3. • 1K LCSS PWB, PL 11.124 Item 1. Perform SCP 5 Final Actions.

Code: 311-100-00-150, 311-101-00-150, 311-158-00-150, 311-163-00-150

Description: LVF BM Paper Entry RAP 311-100-00-150 The lead edge of the sheet is late to the finisher entry sensor Q11-100. 311-101-00-150 The trail edge of the sheet is late from the finisher entry sensor Q11-100. 311-158-00-150 The lead edge of the sheet is late to the finisher entry sensor Q11-100, when feeding to the booklet maker compiler. 311-163-00-150 The trail edge of the sheet is late from the finisher entry sensor Q11-100, when feeding to the booklet maker compiler.
Remedy: Check the following: • LVF PWB DIP switch settings, refer to 311F-150 LVF PWB and LVF BM PWB DIP Switch Settings RAP. • Ensure the paper tray guides are set to the correct position for the size of paper in the tray. • Check the paper entry guide for damage or wear that could cause paper to jam. • Paper jam in the machine to LVF BM paper path, ADJ 11.2-150 Machine to LVF BM Alignment. • IOT exit path and feed rolls. • Feeding performance from a paper tray loaded with a new ream of paper.
Lower the paper entry guide assembly, PL 11.62 Item 7, to access the finisher entry sensor. Enter dC330, code 011-100. Actuate the finisher entry sensor, Q11-100. The display changes. Y↓N→Go to Flag 1. Check Q11-100. Refer to: • GP 11, How to Check a Sensor. • P/J304, LVF PWB. • 311D-150 LVF BM Power Distribution RAP. Repair or install new components as necessary: • Finisher entry sensor, PL 11.74 Item 3. • LVF PWB, PL 11.90 Item 8. Perform SCP 5 Final Actions.

Code: 311-100-00-171, 311-101-00-171

Description: HVF Entry Sensor RAP 311-100-00-171 The paper leading edge is late arriving at the entry sensor. 311-101-00-171 The paper trailing edge is late leaving the entry sensor.
Remedy: Enter dC330 code 011-100. Manually operate the entry sensor, Q11-100. The display changes. Y↓N→Go to Flag 1. Check Q11-100. Refer to: • GP 11 How to Check a Sensor. • P/J101, HVF Control PWB • 311A-171 HVF Power Distribution RAP Install new components as necessary: • Entry sensor, PL 11.156 Item 2. • HVF control PWB, PL 11.157 Item 2. Enter dC330 code 011-000 to run the Transport motor 1, MOT11-000. MOT11-000 runs. Y↓N→Go to Flag 2. Check MOT11-000. Refer to: • GP 10 How to Check a Motor. • P/J102, HVF Control PWB • 311A-171 HVF Power Distribution RAP Install new components as necessary: • Transport motor 1, PL 11.150 Item 2. • HVF control PWB, PL 11.157 Item 2. Check the drive belt on the motor. The drive belt is good. Y↓N→Install a new drive belt, PL 11.150 Item 7. The fault may be intermittent, check for damaged wiring or bad connectors. If necessary install new components: • Entry sensor, PL 11.156 Item 2. • Transport motor 1, PL 11.150 Item 2. • HVF control PWB, PL 11.157 Item 2. • Check if the HVF module has the W/TAG V-006 modifications installed. If the modifications have not been installed perform ADJ 11.13-171 HVF Performance Improvements W/ TAG V-006.

Code: 311-110-00-110

Description: Sheet Late to Hole Punch RAP 311-110-00-110 Sheet late at the punch sensor.
Remedy: . Enter dC330 code 011-110-00. Actuate the punch sensor, Q11-110. The display changes. Y↓N→Go to Flag 1. Check Q11-110. Refer to: • 311G-110 2K LCSS PWB Damage RAP. • GP 11, How to Check a Sensor. • P/J307, 2K LCSS PWB. • 311D-110 2K LCSS Power Distribution RAP Install new components as necessary: • Punch sensor, PL 11.6 Item 7. • 2K LCSS PWB, PL 11.26 Item 1. Perform SCP 5 Final Actions.

Code: 311-110-00-150

Description: LVF BM Sheet Late to Hole Punch RAP 311-110-00-150 Sheet late at the punch sensor.
Remedy: Check the following: • The LVF PWB DIP switch settings, refer to 311F-150 LVF PWB and LVF BM PWB DIP Switch Settings RAP. • Ensure the paper tray guides are set to the correct position for the size of paper in the tray. • For a paper jam at the entrance to the LVF BM. Check that there is no obstruction that would prevent a sheet from arriving in position for punching, refer to the 311H-150 Copy Damage in the LVF BM RAP. • The punch sensor, Q11-110 for chad debris.
. Enter dC330, code 011-110. Actuate the punch sensor, Q11-110. The display changes. Y↓N→Go to Flag 1. Check Q11-110. Refer to: • GP 11, How to Check a Sensor. • P/J307, LVF PWB. • 311D-150 LVF BM Power Distribution RAP Repair or install new components as necessary: • Punch sensor, PL 11.54 Item 7. • LVF PWB, PL 11.90 Item 8. Perform SCP 5 Final Actions.
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie