• Code: E505-0001
• Description: A. Backup data error with the insertion unit (failed data reading) (Document Insertion Unit-J1/Paper Folding Unit-G1) B. EEPRAM error(Finisher-A1/B1). A: Data failed to be read properly B: The checksum for the finisher controller PCB has an error when the power is turned on. (The checksum for the EEPROM data has an error.)
• Remedy: A: DC controller PCB is faulty B: The finisher controller PCB is faulty

• Code: E505-0002
• Description: A. Backup data error with the insertion unit (failed data writing) (Document Insertion Unit-J1/Paper Folding Unit-G1) B.EEPROM error (External * Hole Puncher-A1). The checksum for the EEPROM data has an error.
• Remedy: A. DC controller PCB is faulty B. Punch home position error

• Code: E505-0003
• Description: A. Insertion unit back-up RAM error(Finisher-A1) B. EEPROM error with the insertion unit (failed data reading/writing) (Document Folding Insertion Unit / Insertion Unit -H1). A. The value written in EEPROM and the value extracted from EEPROM doesn't conform. B. Data failed to be read properly
• Remedy: A: 1. The insertion unit controller PCB is faulty. B: DC controller PCB is faulty

• Code: E505-0005
• Description: Paper folding unit back-up RAM error. The value written in EEPROM and the value extracted from EEPROM doesn't conform
• Remedy: 1. The paper folding unit controller PCB is faulty.

• Code: E514-8001
• Description: A. Error in the gripper base motor(Finisher-A1) B. Rear end assist home position error(Finisher-B1). A. The gripper does not come off the gripper base rear sensor when the gripper base motor has been driven for 3sec. B. The stapler does not leave the rear end assist home position when the rear end assist motor has been driven for 3 seconds
• Remedy: A: 1. The connector of the gripper base rear sensor (S117) or the gripper base motor (M116) are disconnected. 2. The wiring of the gripper base rear sensor (S117) or the gripper base motor (M116) are faulty. 3. The gripper base rear sensor (S117) is faulty. 4. The gripper base motor (M116) is faulty. 5. The finisher controller PCB is faulty. B: 1) The rear end assist home position sensor (PI109) is faulty. 2) The wiring between the finisher controller PCB and rear end assist motor is faulty. 3) The end assist mechanism is faulty. 4) The rear end assist motor (M109) is faulty. 5) The finisher con

• Code: E514-8002
• Description: A. Error in the gripper base motor(Finisher-A1) B. Rear end assist home position error(Finisher-B1). A. The gripper base rear sensor dose not detect the gripper when the gripper base motor has been driven for 3sec. B. The stapler does not return to the rear end assist home position when the rear end assist motor has been driven for 3 seconds.
• Remedy: A: 1. The connector of the gripper base rear sensor (S117) or the gripper base motor (M116) are disconnected. 2. The wiring of the gripper base rear sensor (S117) or the gripper base motor (M116) are faulty. 3. The gripper base rear sensor (S117) is faulty. 4. The gripper base motor (M116) is faulty. 5. The finisher controller PCB is faulty. B: 1) The rear end assist home position sensor (PI109) is faulty. 2) The wiring between the finisher controller PCB and rear end assist motor is faulty. 3) The end assist mechanism is faulty. 4) The rear end assist motor (M109) is faulty. 5) The finisher con

• Code: E514-8003
• Description: Error in the gripper motor(Finisher-A1). The gripper does not come off the gripper HP sensor when the gripper motor has been driven for 3sec.
• Remedy: 1. The connector of the gripper HP sensor (S140) or the gripper motor (M117) are disconnected. 2. The wiring of the gripper HP sensor (S140) or the gripper motor (M117) are faulty. 3. The gripper HP sensor (S140) is faulty. 4. The gripper motor (M117) is faulty. 5. The finisher controller PCB is faulty.

• Code: E514-8004
• Description: Error in the gripper motor(Finisher-A1). The gripper HP sensor does not detect the gripper when the gripper motor has been driven for 3sec.
• Remedy: 1. The connector of the gripper HP sensor (S140) or the gripper motor (M117) are disconnected. 2. The wiring of the gripper HP sensor (S140) or the gripper motor (M117) are faulty. 3. The gripper HP sensor (S140) is faulty. 4. The gripper motor (M117) is faulty. 5. The finisher controller PCB is faulty.