• Code: 65.X.X
• Display: 65.X.X OUTPUT DEVICE CONDITION
• Description: An external output device has a condition that needs attention before printing can resume.
• Remedy: 1. Turn the MFP off then on. If necessary, reseat the output device. Ensure that the output device is connected and the cable is tightened. 2. Ensure that no error lights are illuminated on the output device.

• Code: 66.XX.YY
• Display: 66.XX.YY OUTPUT DEVICE FAILURE
• Description: An error occurred in an external paperhandling accessory. • 66.00.15 = The output device was removed and then replaced while the MFP power was on. • 66.12.01 = Output-lift roller or paddlemotor error • 66.12.02 = Jogger-motor error • 66.12.03 = Stapler motor errorand
• Remedy: 1. Turn the MFP power off. 2. Check that the accessory is properly seated on and connected to the MFP, without any gaps between the MFP and the accessory. If the accessory uses cables, disconnect and reconnect them. 3. Turn the MFP power on. 4. If this message persists, replace the output device.

• Code: 68.X
• Display: 68.X PERMANENT STORAGE FULL
• Description: A non-volatile storage device is full. Touching OK should clear the message. Printing can continue, but there may be unexpected behavior.
  X Description: 68.0 - Onboard NVRAM 68.1 - Removable disk or flash66.12.0
• Remedy: 1. Touch OK to continue. 2. For 68.0 errors, initialize the NVRAM. 3. For 68.1 errors: • Use HP Web Jetadmin to delete files from the hard disk or flash card. • Reinitialize the hard disk. • Replace the hard disk. • Replace the formatter.

• Code: 68.X
• Display: 68.X PERMANENT STORAGE WRITE FAIL
• Description: The MFP NVRAM is full. Some settings that are saved in the NVRAM might have been reset to the factory defaults. Printing can continue, but some unexpected functions might occur if an error occurred in permanent storage
  X Description: 68.0 - Onboard NVRAM failure 68.1 - Memory DIMM or hard disk failure
• Remedy: 1. Touch OK to continue. 2. For 68.0 errors, perform an NVRAM initialization. 3. For 68.1 errors: • Use HP Web Jetadmin to delete files from the hard disk or flash card. • Reinitialize the hard disk. • Replace the hard disk. • Replace the formatter. 4. For 6810 errors that persist, reinitialize the hard disk or flash card

• Code: 68.X
• Display: 68.X STORAGE ERROR SETTINGS CHANGED
• Description: One or more MFP settings saved in the nonvolatile storage device is invalid and has been reset to its factory default. Touching OK should clear the message. Printing can continue, but there may be unexpected behavior.
  0 - NVRAM 1 - Disk or flash
• Remedy: 1. Touch OK to continue. 2. If the message persists, turn the MFP off then on. 3. For 68.0 errors, reinitialize the NVRAM.

• Code: 69.X
• Display: 69.X PRINTER ERROR
• Description: An MFP error has occurred.
  X - 0, 1 Duplex unit is not functioning.
• Remedy: 1. Turn the MFP off then on. Press ? for more information. 2. Check the duplex connection to ensure that it is connected to the duplexer. 3. Ensure that connector J1030 is connected at the DC controller. 4. Upgrade the firmware. 5. Replace the duplexer. Replace the DC controller.

• Code: 8X.YYYY
• Display: 8X.YYYY EIO X ERROR
• Description: The I/O accessory card in slot X has encountered a critical error.
  X Description 1: error in slot 1
• Remedy: 1. Turn the MFP off then on. 2. If the problem persists, reseat the EIO card. 3. Replace the EIO card.

• Code: 8X.YYYY
• Display: 8X.YYYY EMBEDDED JETDIRECT ERROR
• Description: This message is generated by a failure of the embedded Jetdirect print server.
• Remedy: Turn the MFP off then on. Press ? for more information