• Code: 45.03:00
• Description: Rewinder driver system fault. There is a system fault with the Rewinder driver.
• Remedy: • Switch the Power OFF from the back of the Printer and disconnect the Power cord. Reconnect the power cord and power On the Printer. • Check the Rewinder motor cables are not damaged and are correctly connected to the PrintMech PCA. • Replace the Rewinder Motor . • Replace the PrintMech PCA .

• Code: 46:03
• Description: Primer Servo shutdown. There is a problem with the servo of the Primer.
• Remedy: • Switch the Power OFF from the back of the Printer and disconnect the Power cord. Reconnect the power cord and power On the Printer. • Check to make sure there is not obstruction in the Primer mechanism. • Replace the Primer Assembly . • Replace the PrintMech PCA . • Replace the Interconnect PCA .

• Code: 46:10
• Description: Electrical fault in the Primer motor. Electrical fault in Primer motor.
• Remedy: • Switch the Power OFF from the back of the Printer and disconnect the Power cord. Reconnect the power cord and power On the Printer. • Check to make sure there is not obstruction in the Primer mechanism. • Replace the Primer Assembly . • Replace the PrintMech PCA . • Replace the Interconnect PCA 

• Code: 46:13
• Description: Primer distance failed
• Remedy: • Check that the Primer arm is not damaged and there are no obstructions in the way. • Switch the Power OFF from the back of the Printer and disconnect the Power cord. Reconnect the power cord and power On the Printer. • Replace the Primer Assembly .

• Code: 50.01:10
• Description: Connection problem with OMAS. Error with the Optical Media Advance Sensor (OMAS) component or with the cable between sensor and the PCA.
• Remedy: • Switch the Power OFF from the back of the Printer and disconnect the Power cord. Reconnect the power cord and power On the Printer. • Check that the Printer has the latest firmware version, if not, update the firmware to the latest version. • Check that the OMAS Module cable is not damaged and is correctly connected to the OMAS Controller PCA. • Replace the OMAS Controller Card  • Replace the OMAS Module .

• Code: 50.01:11
• Description: Error with Media Advance Sensor or with cable. Error with the CAN cable of the CAN driver.
• Remedy: • Check the cable is not damaged and is correctly connected between the Sausalito and the OMAS Controller Board. • Replace the OMAS controller PCA • Replace the Sausalito PCA  • Replace the cable between the Sausalito and the OMAS Controller Board.

• Code: 50.02:10
• Description: Problem with OMAS Controller PCA. Error with the media advance sensor controller board.
• Remedy: • Switch the Power OFF from the back of the Printer and disconnect the Power cord. Reconnect the power cord and power On the Printer. • Check that the Printer has the latest Firmware version, if not, update the firmware to the latest version. • Check that the CAN cable and the Encoder Cable are correctly connected to the OMAS PCA and the Sausalito PCA. • Check the connection between the OMAS PCA and the Sausalito PCA (the Sausalito is the card connected just behind the OMAS PCA). • Check that the OMAS Module cable is not damaged and is correctly connected to the OMAS Controller PCA. • Replace the OMAS Controller Card .

• Code: 50:01
• Description: OMAS Navigation failure
• Remedy: Before preceding with corrective action for this error, it must be noted that some substrates cannot be detected by the OMAS. If the substrate has a high plastic content, is very reflective or is very smooth the OMAS will not detect it. In this case, the OMAS sensor must be disabled if the customer wants to carry on using the same media. To disable/enable the OMAS ËPage 189. It can also be disabled from the RIP.
  • Switch the Power OFF from the back of the Printer and disconnect the Power cord. Reconnect the power cord and power On the Printer. • Clean the OMAS window ËPage 602. • Perform the OMAS check service test ËPage 189. • Replace the OMAS.