Description: There is a communication failure with the print cartridge.
Remedy: - Press the power button to turn the product off. - Verify that the print cartridge is installed correctly. Remove and reinstall the print cartridge. - If the error persists, reconnect the J581 connector on the engine controller PCA. - If the error persists, replace the print cartridge.
Description: There is a communication failure with the photosensitive drum.
Remedy: - Press the power button to turn the product off. - If a surge protector is being used, remove it. Plug the power cord directly into a wall outlet. - Wait at least 30 seconds, turn the product on, and then wait for the product to initialize. - If the error persists, reconnect the J581 connector on the engine controller PCA. - If the error persists, replace the print cartridge.
Description: There is a communication failure with the photosensitive drum.
Remedy: - Press the power button to turn the product off. - If a surge protector is being used, remove it. Plug the power cord directly into a wall outlet. - Wait at least 30 seconds, turn the product on, and then wait for the product to initialize. - If the error persists, reconnect the J581 connector on the engine controller PCA. - If the error persists, replace the print cartridge.
Description: The product has experienced a firmware error.
Remedy: 1. Press the power button to turn the product off. 2. If a surge protector is being used, remove it. Plug the power cord directly into a wall outlet. 3. Wait at least 30 seconds, turn the product on, and then wait for the product to initialize. 4. If the error persists, disconnect and then reconnect the FFCs and the connectors on the formatter PCA. 5. If the error persists, replace the formatter PCA.
Description: The product has an internal hardware error.
Remedy: 1. Press the power button to turn the product off. 2. If a surge protector is in use, remove it. Connect the power cord directly into a wall outlet. 3. Wait at least 25 minutes, turn the product on, and then wait for the product to initialize. 4. If the error persists, reconnect J101 and J552 on the engine controller PCA. 5. If the error persists, check the power source. Make sure that the power source meets the minimum system requirements (40Hz to 70Hz). 6. If the error persists, replace the fuser. 7. If the error persists, replace the engine controller PCA.
Remedy: 1. Press the power button to turn the product off. 2. If a surge protector is in use, remove it. Connect the power cord directly into a wall outlet. 3. Wait at least 30 seconds, turn the product on, and then wait for the product to initialize. 4. If the issue persists, reconnect the J1 and J801 connectors on the laser scanner PCA and the J542 connector on the engine controller PCA. 5. If the issue persists, replace the laser scanner assembly.
Remedy: 1. Press the power button to turn the product off. 2. If a surge protector is in use, remove it. Connect the power cord directly into a wall outlet. 3. Wait at least 30 seconds, turn the product on, and then wait for the product to initialize. 4. If the error persists, reconnect the J1103 connector on the duplex connector PCA. 5. If the error persists, replace the main fan.
Description: The product has experienced a firmware error
Remedy: 1. Press the power button to turn the product off. 2. If a surge protector is in use, remove it. Connect the power cord directly into a wall outlet. 3. Wait at least 30 seconds, turn the product on, and then wait for the product to initialize. 4. If the error persists, disconnect and then reconnect the FFCs and the connectors on the formatter PCA. 5. If the issue persists, replace the formatter PCA.
Nhận ưu đãi sớm nhất khi chương trình diễn ra
Đăng ký nhận bản tin
Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này.
Chính sách cookie
Những cookie này là cần thiết để trang web hoạt động đúng cách.
Những cookie này giúp chúng tôi hiểu cách khách truy cập tương tác với trang web.
Những cookie này được sử dụng để cung cấp quảng cáo cá nhân hóa.