Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Konica-Minolta bizhub 4020 — Trang 7/22

Code: 132.16

Description: TDS calibration at maximum.
Remedy: Step 1: Remove the transfer roll, and then check for loose toner blocking the toner density sensor. Is it free of loose toner? Yes: Go to step 2. No: Clean the sensor.
Step 2: Check the TDS for proper operation: 1. Lower the ACM assembly. 2. Move the toner density sensor wiper from left to right. Does it move freely? Yes: Go to step 3. No: Reinstall the wiper properly. If it still cannot move freely, then replace the toner density sensor.
Step 3: Check the cable JTDS for proper connection. Is it properly connected? Yes: Go to step 4. No: Reseat the cable.
Step 4: Check the cable JTDS for damage and pinch points. Is it free of damage? Yes: Replace the controller board. No: Replace the toner density sensor.

Code: 132.17

Description: TDS calibration too low.
Remedy: Step 1: Remove the transfer roll, and then check for loose toner blocking the toner density sensor. Is it free of loose toner? Yes: Go to step 2. No: Clean the sensor.
Step 2: Check the TDS for proper operation: 1. Lower the ACM assembly. 2. Move the toner density sensor wiper from left to right. Does it move freely? Yes: Go to step 3. No: Reinstall the wiper properly. If it still cannot move freely, then replace the toner density sensor.
Step 3: Check the cable JTDS for proper connection. Is it properly connected? Yes: Go to step 4. No: Reseat the cable.
Step 4: Check the cable JTDS for damage and pinch points. Is it free of damage? Yes: Replace the controller board. No: Replace the toner density sensor.

Code: 132.18

Description: TDS calibration too close to baseline.
Remedy: Step 1: Remove the transfer roll, and then check for loose toner blocking the toner density sensor. Is it free of loose toner? Yes: Go to step 2. No: Clean the sensor.
Step 2: Check the TDS for proper operation: 1. Lower the ACM assembly. 2. Move the toner density sensor wiper from left to right. Does it move freely? Yes: Go to step 3. No: Reinstall the wiper properly. If it still cannot move freely, then replace the toner density sensor.
Step 3: Check the cable JTDS for proper connection. Is it properly connected? Yes: Go to step 4. No: Reseat the cable.
Step 4: Check the cable JTDS for damage and pinch points. Is it free of damage? Yes: Replace the controller board. No: Replace the toner density sensor.

Code: 132.32

Description: PC drum measurement too high.
Remedy: Step 1: Remove the transfer roll, and then check for loose toner blocking the toner density sensor. Is it free of loose toner? Yes: Go to step 2. No: Clean the sensor.
Step 2: Check the TDS for proper operation: 1. Lower the ACM assembly. 2. Move the toner density sensor wiper from left to right. Does it move freely? Yes: Go to step 3. No: Reinstall the wiper properly. If it still cannot move freely, then replace the toner density sensor.
Step 3: Check the cable JTDS for proper connection. Is it properly connected? Yes: Go to step 4. No: Reseat the cable.
Step 4: Check the cable JTDS for damage and pinch points. Is it free of damage? Yes: Replace the controller board. No: Replace the toner density sensor.

Code: 132.33

Description: PC drum measurement too different from calibration.
Remedy: Step 1: Remove the transfer roll, and then check for loose toner blocking the toner density sensor. Is it free of loose toner? Yes: Go to step 2. No: Clean the sensor.
Step 2: Check the TDS for proper operation: 1. Lower the ACM assembly. 2. Move the toner density sensor wiper from left to right. Does it move freely? Yes: Go to step 3. No: Reinstall the wiper properly. If it still cannot move freely, then replace the toner density sensor.
Step 3: Check the cable JTDS for proper connection. Is it properly connected? Yes: Go to step 4. No: Reseat the cable.
Step 4: Check the cable JTDS for damage and pinch points. Is it free of damage? Yes: Replace the controller board. No: Replace the toner density sensor.

Code: 132.34

Description: PC drum measurement too close to baseline.
Remedy: Step 1: Remove the transfer roll, and then check for loose toner blocking the toner density sensor. Is it free of loose toner? Yes: Go to step 2. No: Clean the sensor.
Step 2: Check the TDS for proper operation: 1. Lower the ACM assembly. 2. Move the toner density sensor wiper from left to right. Does it move freely? Yes: Go to step 3. No: Reinstall the wiper properly. If it still cannot move freely, then replace the toner density sensor.
Step 3: Check the cable JTDS for proper connection. Is it properly connected? Yes: Go to step 4. No: Reseat the cable.
Step 4: Check the cable JTDS for damage and pinch points. Is it free of damage? Yes: Replace the controller board. No: Replace the toner density sensor.

Code: 133.05

Description: CTLS reading above maximum expected value.
Remedy: Step 1: Check for loose toner blocking the CTLS. Is it free of any loose toner? Yes: Go to step 2. No: Clean the CTLS.
Step 2: • Check the cable PCN3 for proper connection to the power supply. • Check the CTLS cable for proper connection to the controller board. Yes: Go to step 3. Reseat the cables.
Step 3 Check the cable PCN3 and CTLS cable for damage. Are they free of damage? Yes: Replace the controller board. No: Replace the printer.

Code: 133.06

Description: CTLS reading below minimum expected value.
Remedy: Step 1: Check for loose toner blocking the CTLS. Is it free of any loose toner? Yes: Go to step 2. No: Clean the CTLS.
Step 2: • Check the cable PCN3 for proper connection to the power supply. • Check the CTLS cable for proper connection to the controller board. Yes: Go to step 3. Reseat the cables.
Step 3 Check the cable PCN3 and CTLS cable for damage. Are they free of damage? Yes: Replace the controller board. No: Replace the printer.
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie