Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Konica-Minolta bizhub C450 — Trang 10/14

Code: C2657

Description: Yellow LPH correction data download failure
Remedy: 1 Correct the harness connection between LPH and PWB-LED if faulty. 2 Correct the harness connection between PWBLED and PWB-MFPC if faulty. 3 Change LPH Assy. 4 Change PWB-LED. 5 Change PWB-MFPC. 6 Change PWB-MC.

Code: C2658

Description: Black LPH correction data download failure
Remedy: 1 Correct the harness connection between LPH and PWB-LED if faulty. 2 Correct the harness connection between PWBLED and PWB-MFPC if faulty. 3 Change LPH Assy. 4 Change PWB-LED. 5 Change PWB-MFPC. 6 Change PWB-MC.

Code: C3101

Description: Fusing Pressure Roller pressure/retraction failure
• No change is observed in the encoder sensor pulse even after the lapse of 0.5 sec. after the Fusing Pressure/Retraction Motor has started turning for a sequence of the Fusing Pressure Roller’s retracting motion. • No change is observed in the encoder sensor pulse even after the lapse of 0.5 sec. after the Fusing Pressure/Retraction Motor has started turning for a sequence of the Fusing Pressure Roller’s pressing motion. • The Fusing Pressure Position Sensor is not activated (pressed position) even when 30 encoder sensor pulses are counted after the Fusing Pressure/Retraction Motor has started turning for a sequence of the Fusing Pressure Roller’s pressing motion.
Remedy: 1 Check the M9 connector for proper connection and correct as necessary. 2 PC33 I/O check PWB-MC PJ26MC-12 (ON). 3 PC33 operation check. 4 M19 operation check PWB-MC PJ14MC-5 to 6 C to D-6. 5 Change Fusing Unit. 6 Change PWB-MC.

Code: C3201

Description: Fusing Drive Motor’s failure to turn
• The Fan Lock signal remains HIGH for a predetermined continuous period of time while the Motor remains stationary.
Remedy: 1 Check the M2 connector for proper connection and correct as necessary. 2 Check the Fusing Unit drive for possible overload and correct as necessary. 3 Check the PWB-MC connector for proper connection and correct as necessary. PWB-MC PJ2MC-5 (DC24 V) H-2. 4 M2 operation check PWB-MC PJ31MC-10 (REM) PWB-MC PJ31MC-13 (LOCK) C to D-17. 5 Change PWB-MC.

Code: C3202

Description: Fusing Drive Motor turning at abnormal timing
• The Motor Lock signal remains LOW for a predetermined continuous period of time while the Motor remains stationary.
Remedy: 1 M2 operation check PWB-MC PJ31MC-10 (REM) PWB-MC PJ31MC-13 (LOCK) C to D-17. 2 Change PWB-MC.

Code: C3301

Description: Fusing Cooling Fan Motor/1 failure to turn
• The Fan Lock signal remains HIGH for a predetermined continuous period of time while the Motor remains stationary
Remedy: 1 Check the connector of motor for proper connection and correct as necessary. 2 Check the fan for possible overload and correct as necessary. 3 M9 operation check PWB-MC PJ6MC-4 (REM) PWB-MC PJ6MC-6 (LOCK) K-9. 4 Change PU-1.

Code: C3302

Description: Fusing Cooling Fan Motor/1 or Fusing Cooling Fan Motor/2 failure to turn
• The Fan Lock signal remains HIGH for a predetermined continuous period of time while the Motor remains stationary.
Remedy: 1 Check the connector of motor for proper connection and correct as necessary. 2 Check the fan for possible overload and correct as necessary. 3 M15, M16 operation check PWB-MC PJ15MC-4 (REM) PWB-MC PJ15MC-6 (LOCK) PWB-MC PJ15MC-7 (REM) PWB-MC PJ15MC-9 (LOCK) C to D-21. 4 Change PWB-MC.

Code: C3451

Description: Heating Roller warm-up failure
• The temperature of the Heating Roller does not reach 100 °C within 50 sec. after the Heating Roller Heater Lamp has been turned ON. • The temperature of the Heating Roller does not reach 100 °C and that of the Fusing Pressure Roller does not reach 195 °C within 200 sec. after the Heating Roller Heater Lamp has been turned ON. • The voltage of the Heating Roller Thermistor does not increase by five steps within 20 sec. after the Heating Roller Heater Lamp has been turned ON. • No zero cross signal is detected even with the lapse of 1 sec. or more after the Heating Roller Heater Lamp has been turned ON.
Remedy: 1 Check the Fusing Unit for correct installation (whether it is secured in position). 2 Check the Fusing Unit, PWB-MC and PU1 for proper connection and correct or change as necessary. 3 Change Fusing Unit. 4 Change PWB-MC. 5 Change PU1.
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie