Description: Laser beam detection error 1: C (Cyan)
The laser synchronization sensor failed to detect the beginning and end of the laser beam flash for the designated color onto the polygon mirror while the mirror is rotating at the prescribed number of revolutions.
Description: Laser Synchronization Detector Error 1: K Leading Edge: LD0
While the polygon motor is rotating normally, no synchronizing detection signal is output for LD0 black, or leading edge, even after the laser diode has been firing for 2 sec.
Causes: • Harness between the laser synchronizing detector and I/F unit is disconnected, defective • Laser synchronizing detector defective • Beam not reflected in photo detection • GAVD on the BICU is defective • LD driver board defective • LDB defective • BCU defective • Check board connections, replace
Description: Laser Synchronization Detector Error 2: K Leading Edge (Other than LD0)
While the polygon motor is rotating normally, no synchronizing detection signal is output for black, leading edge for any LD other than LD0, even after the laser diode has been firing for 2 sec.
Causes: • Beam not reflected in photo detection • GAVD on the BICU defective • LD driver defective • LDB defective • BCU defective • Check board connections, replace
Description: Laser Synchronization Detector Error 1: Y Leading Edge: LD0
While the polygon motor is rotating normally, no synchronizing detection signal is output for LD0 yellow, leading edge, even after the laser diode has been firing for 2 sec.
Causes: • Harness between the laser synchronizing detector and I/F unit is disconnected, defective • Laser synchronizing detector defective • GAVD on the BICU defective • LD driver board defective • LDB defective • BCU defective • Check board connections, replace
Description: Laser Synchronization Detector Error 2: Y Leading Edge (Other than LD0)
While the polygon motor is rotating normally, no synchronizing detection signal is output for yellow, leading edgefor any LD other than LD0, even after the laser diode has been firing for 2 sec.
Causes: • Beam not reflected in photo detection • GAVD on the BICU defective • LD driver defective • LDB defective • BCU defective • Check board connections, replace
Description: Laser Synchronization Detector Error 1: M Leading Edge: LD0
While the polygon motor is rotating normally, no synchronizing detection signal is output for LD0 magenta, leading edge, even after the laser diode has been firing for 2 sec.
Causes: • Harness between the laser synchronizing detector and I/F unit is disconnected, defective • Laser synchronizing detector defective • GAVD on the BICU defective • LD driver board defective • LDB defective • BCU defective • Check board connections, replace
Description: Laser Synchronization Detector Error 2: M Leading Edge (Other than LD0)
While the polygon motor is rotating normally, no synchronizing detection signal is output for magenta, leading edge for any LD other than LD0, even after the laser diode has been firing for 2 sec.
Description: Laser Synchronization Detector Error 1: C Leading Edge: LD0
While the polygon motor is rotating normally, no synchronizing detection signal is output for LD0 cyan, leading edge, even after the laser diode has been firing for 2 sec.
Causes: • Harness between the laser synchronizing detector and I/F unit is disconnected, defective • Laser synchronizing detector defective • GAVD on the BICU defective • LD driver board defective • LDB defective • BCU defective • Check board connections, replace
Nhận ưu đãi sớm nhất khi chương trình diễn ra
Đăng ký nhận bản tin
Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này.
Chính sách cookie
Những cookie này là cần thiết để trang web hoạt động đúng cách.
Những cookie này giúp chúng tôi hiểu cách khách truy cập tương tác với trang web.
Những cookie này được sử dụng để cung cấp quảng cáo cá nhân hóa.