Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Ricoh M132 SP8300DN AL-P2 — Trang 15/20

Code: 829

Description: Self-diagnostic error: Optional RAM [XXXX]: Detailed error code
Causes: [0301] Verification error Error detected during a write/verify check for the optional RAM (SDRAM DIMM). • Loose connection • Defective SDRAM DIMM • Defective controller Turn the main switch off and on. Replace the SDRAM DIMM. Replace the controller. [0302] Memory structure data error The memory structure data error for the optional RAM (SDRAM DIMM) is detected when the self-diagnostic is executed. • Defective RAM DIMM • Defective SPD ROM on RAM DIMM • Defective 12C bus. Replace the RAM DIMM.
Remedy:

Code: 833

Description: Self-diagnostic error 8: Engine I/F ASIC
Causes: [0F30] [0F31] ASIC (Mandolin) for system control could not be detected. After the PCI configuration, the device ID for the ASIC could not be checked. Replace the bridge board. [0F41] ASIC (Mandolin) for system control could not be detected. After the PCI configuration, the device ID for the ASIC could not be checked. Replace the bridge board. [50B1] Could not initialize or read the bus connection. Check for loose connections at the mother board. Replace the bridge board. [50B2] Value of the SSCG register is incorrect. Check for loose connections at the mother board. Replace the bridge board.
Remedy:

Code: 835

Description: Self-diagnostic error: Centronic device
Causes: [1102] Loopback connector is connected but check results in an error. • IEEE1284 connector error • Centronic loopback connector defective Replace the controller board. [110C] Loopback connector is connected but check results in an error. • ASIC device error • IEEE1284 connector error • Centronic loopback connector defective Replace the controller board. [1120] Centronic loopback connector is not connected for detailed self-diagnostic test. • Centronic loopback connector not connected correctly • Centronic loopback connector defective • ASIC device defective Replace the controller board.
Remedy:

Code: 838

Description: Self-diagnostic Error: Clock Generator
Causes: [2701] A verify error occurred when setting data was read from the clock generator via the I2C bus. • Defective clock generator • Defective I2C bus • Defective I2C port on the CPU Replace the controller board.
Remedy:

Code: 839

Description: USB NAND Flash ROM error
Causes: [9001] USB NAND Flash ROM cannot be read. • Defective controller board [9101] The ID of the USB NAND Flash ROM cannot be read. • Defective controller board [9110] The USB NAND Flash ROM controller is disconnected. • Defective controller board
Remedy:

Code: 840

Description: EEPROM error 1: EEPROM access • During the I/O processing, a reading error occurred. The 3rd reading failure causes this SC code. • During the I/O processing, a writing error occurred.
Causes: Defective EEPROM
Remedy:

Code: 841

Description: EEPROM reading error. Mirrored data of the EEPROM is different from the original data in EEPROM.
Causes: Data in the EEPROM is overwritten for some reason.
Remedy:

Code: 842

Description: Nand-Flash update VerifyError SCS detected abnormal writing (verifying Error) in the module which is written in Nand-Flash on the time of ROM remote update or ROM update.
Causes: • This SC is logged at 1st error detection.SC819 is issued at 2nd error detection. • SC819 is issued at 2nd error detection. Defective Nand-Flash (controller board)
Remedy:
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie