Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Sharp MXM700U — Trang 6/16

Code: F1-19

Description: Finisher/alignment motor trouble
When operating the alignment motor, it does not move from the home position in 2sec. When operating the alignment motor, it does not return to the home position in 2sec.
Causes: Motor lock Motor RPM abnormality Overcurrent to the motor Finisher control PWB trouble
Remedy: Use SIM 3-3 to check the motor operation.

Code: F1-31

Description: Finisher saddle folding sensor trouble
When the motor rotation speed (linear velocity) at every 200msec falls below the specified level. When moving to the home position, the home position sensor does not turn on within the specified time. When shifting from the home position to the lead edge, the home position sensor does not turn off within the specified time.
Causes: Sensor breakage Harness disconnection Console finisher control PWB trouble
Remedy: Use SIM 3-2 to check the sensor operation.

Code: F1-32

Description: Finisher-saddle communication trouble
Communication error between the finisher and the saddle When the motor rotation speed (linear velocity) at every 200msec falls below the specified level. When moving to the home position, the home position sensor does not turn on within the specified time. When shifting from the home position to the lead edge, the home position sensor does not turn off within the specified time.
Causes: Improper connection or disconnection of the connector and the harness between the finisher and the saddle unit.
Finisher control PWB trouble Control PWB (PCU) trouble
Malfunction caused by noises
Remedy: Case 1 Cause Improper connection or disconnection of the connector and the harness between the finisher and the saddle unit. Check and remedy Check the connector and the harness in the communication line. Case 2 Cause Finisher control PWB trouble Control PWB (PCU) trouble Check and remedy Replace the finisher control PWB. Case 3 Cause Malfunction caused by noises Check and remedy Canceled by turning ON/ OFF the power.

Code: F1-33

Description: Finisher/punch shift motor trouble
When operating the punch shift motor, it does not move from the home position in 4sec. When operating the punch shift motor, it does not return to the home position in 4sec.
Causes: Motor lock Motor RPM abnormality Overcurrent to the motor Finisher control PWB trouble
Remedy: Use SIM 3-3 to check the motor operation.

Code: F1-34

Description: Finisher/punch motor trouble
When learning the punch unit, it does not complete normally and does not return to the home position. When executing punching, it does not shift from the home position in 0.2sec, or it overruns to go into non-HP state. When operating the punch unit, the encoder input cannot be detected within 0.1sec.
Causes: Motor lock Motor RPM abnormality Overcurrent to the motor Finisher control PWB trouble
Remedy: Use SIM 3-3 to check the motor operation.

Code: F1-37

Description: Finisher/ backup RAM trouble
When backup RAM data check sum is NG when turning on the power.
Causes: Finisher control PWB trouble Malfunction caused by noises
Remedy: Replace the finisher control PWB.

Code: F1-38

Description: Finisher/punch backup ROM trouble
Punch unit backup RAM data are garbled.
Causes: Punch control PWB trouble Malfunction caused by noises
Remedy: Replace the punch control PWB.

Code: F1-41

Description: Finisher/saddle positioning plate motor trouble
The positioning motor HP sensor does not turn on within 1.33sec after starting the motor. The positioning motor HP sensor does not turn off within 1sec after starting the motor.
Causes: Finisher control PWB trouble Malfunction caused by noises
Remedy: Replace the finisher control PWB.
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie