• Code: EA90
• Description: Door open jam: The delivery cover or inlet cover has opened during printing [MJ-1103/1104].
• Causes: Delivery cover sensor (PI3) Inlet cover sensor (PI9) Saddle stitcher controller board
• Remedy: Finisher, saddle stitcher • Check if there is any paper in the finisher, saddle stitcher or the on the transport path of the equipment. Remove it if there is. Delivery cover sensor (PI3) • Sensor check • Connector check • Harness check Inlet cover sensor (PI9) • Sensor check • Connector check • Harness check Saddle stitcher controller board • Connector check(J10, J11) • Board check

• Code: EAA0
• Description: Power-ON jam: Paper exists at No.1 paper sensor, No. 2 paper sensor, No.3 paper sensor, vertical path paper sensor or delivery sensor when power is turned ON. [MJ-1103/1104]
• Causes: No. 1 paper sensor (PI18) No. 2 paper sensor (PI19) No. 3 paper sensor (PI20) Vertical path paper sensor (PI17) Delivery sensor (PI11) Saddle stitcher controller board
• Remedy: Finisher, saddle stitcher • Check if there is any paper in the finisher, saddle stitcher or the on the transport path of the equipment. Remove it if there is. No. 1 paper sensor (PI18) • Sensor check • Connector check • Harness check No. 2 paper sensor (PI19) • Sensor check • Connector check • Harness check No. 3 paper sensor (PI20) • Sensor check • Connector check • Harness check Vertical path paper sensor (PI17) • Sensor check • Connector check • Harness check Delivery sensor (PI11) • Sensor check • Connector check • Harness check Saddle stitcher controller board • Connector check(J10, J13) • Board check

• Code: EAB0
• Description: Transport stop jam: The paper which passed through the inlet sensor does not reach or pass No.1 paper sensor, No. 2 paper sensor, No.3 paper sensor or delivery sensor. [MJ-1103/1104]
• Causes: No. 1 paper sensor (PI18) No. 2 paper sensor (PI19) No. 3 paper sensor (PI20) Delivery sensor (PI11) Saddle stitcher controller board
• Remedy: Finisher, saddle stitcher • Check if there is any paper in the finisher, saddle stitcher or the on the transport path of the equipment. Remove it if there is. No. 1 paper sensor (PI18) • Sensor check • Connector check • Harness check No. 2 paper sensor (PI19) • Sensor check • Connector check • Harness check No. 3 paper sensor (PI20) • Sensor check • Connector check • Harness check Delivery sensor (PI11) • Sensor check • Connector check • Harness check Saddle stitcher controller board • Connector check(J9, J10) • Board check

• Code: EAB1
• Description: Short paper jam (Saddle Stitch Finisher)
• Causes: Feeding sensor (S22) Junction box paper detection sensor (S26) Transport path-2 (S27) Transport path-3 (S28) Ejecting roller (S29) Interface PC board (I/F) Saddle stitcher controller board Finisher controller board
• Remedy: Finisher, saddle stitcher • Check if there is any paper in the finisher, saddle stitcher or the on the transport path of the equipment. Remove it if there is. • Use paper accepted in the specifications. Feeding sensor (S22) • Sensor check • Connector check • Harness check Junction box paper detection sensor (S26) • Sensor check • Connector check • Harness check Transport path-2 (S27) • Sensor check • Connector check • Harness check Transport path-3 (S28) • Sensor check • Connector check • Harness check Ejecting roller (S29) • Sensor check • Connector check • Harness check Interface PC board (I/F) • Connector check(CN8) • Board check Saddle stitcher controller board • Connector check(CN20) • Board check Finisher controller board • Connector check • Board check

• Code: EAD0
• Description: Print end command time-out jam: The printing has not finished normally because of the communication error between the SYS board and LGC board at the end of printing.
• Causes: SYS board LGC board
• Remedy: Power • Check if the error is cleared by turning the power OFF and then back ON. SYS board • Connector check • Board check LGC board • Connector check • Board check

• Code: EAE0
• Description: Receiving time time-out jam: The printing has been interrupted because of the communication error between the equipment and finisher when the paper is transported from the equipment to the finisher.
• Causes: Finisher controller board
• Remedy: Finisher • Is the finisher working? • Check if the voltage (24V) is being supplied to the finisher. Finisher controller board • Connector check • Board check

• Code: EB30
• Description: Ready time time-out jam: The equipment judges that the paper transport to the finisher is disabled because of the communication error between the equipment and finisher at the start of printing.
• Causes: Finisher controller board LGC board
• Remedy: Finisher • Check if there is any paper in the equipment. Remove it if there is. Finisher controller board • Connector check • Board check LGC board • Connector check • Board check

• Code: EB50
• Description: Paper remaining on the transport path: The multiple feeding of preceding paper caused the misfeeding of upcoming paper.
• Causes: 1st drawer feed sensor Bypass feed sensor ADU exit sensor Registration sensor 1st drawer feed sensor 2nd drawer feed sensor ADU board LGC board Rollers
• Remedy: 1st drawer feed sensor (When the paper is fed from the 1st drawer:) • Sensor check (Perform the input check: 03-[SCAN]ON/[1]/[H]) • Connector check • Harness check Bypass feed sensor (When the paper is fed from the bypass feed unit:) • Sensor check (Perform the input check: 03-[SCAN]ON/[3]/[A]) • Connector check • Harness check ADU exit sensor (When the paper is fed from the ADU:) • Sensor check (Perform the input check: 03-[SCAN]ON/[3]/[G]) • Connector check • Harness check Registration sensor (When the paper is fed from the ADU:) • Sensor check (Perform the input check: 03-[ALL]OFF/[4]/[B], 03- [COPY]ON/[5]/[H]) • Connector check • Harness check 1st drawer feed sensor (When the paper is fed from any of the 2nd drawer, PFP or LCF:) • Sensor check (Perform the input check: 03-[SCAN]ON/[1]/[H]) • Connector check • Harness check 2nd drawer feed sensor (When the paper is fed from any of the 2nd drawer, PFP or LCF:) • Sensor check (Perform the input check: 03-[SCAN]ON/[1]/[G]) • Connector check • Harness check ADU board • Connector check (CN211, CN213) • Board check LGC board • Connector check (CN337, CN338, CN347, CN348) • Board check Drive unit, Rollers • Gear check • Roller check