• Code: EB60
• Description: Paper remaining on the transport path: The multiple feeding of preceding paper caused the misfeeding of upcoming paper (redetection after no jam is detected at [EB50]).
• Causes: Registration sensor PFC board Rollers
• Remedy: Registration sensor • Sensor check (Perform the input check: 03-[ALL]OFF/[4]/[B], 03- [COPY]ON/[5]/[H]) • Connector check • Harness check PFC board • Connector check (CN516) • Board check Drive unit, Rollers • Gear check • Roller ch

• Code: ED10
• Description: Skew adjustment motor (M1) home position detection abnormality: The Skew adjustment motor is not at the home position. [MJ-1103/1104 (when MJ-6102 is installed)]
• Causes: Skew adjustment motor (M1) Skew HP sensor (S2) Punch controller board
• Remedy: Finisher • Check if there is any paper in the finisher. Remove it if there is. Skew adjustment motor (M1) • Motor check • Connector check • Harness check Skew HP sensor (S2) • Sensor check • Connector check • Harness check Punch controller board • Connector check • Board check

• Code: ED11
• Description: Sideways adjustment motor (M2) home position detection error: The Sideways adjustment motor is not at the home position. [MJ-1103/1104 (when MJ6102 is installed)]
• Causes: Sideways adjustment motor (M2) Sideways deviation HP sensor (S3 Punch controller board
• Remedy: Finisher • Check if there is any paper in the finisher. Remove it if there is. Sideways adjustment motor (M2) • Rotate sideways adjustment motor and fix its mechanism if it does not rotate smoothly. • Motor check • Connector check • Harness check Sideways deviation HP sensor (S3) • Sensor check • Connector check • Harness check Punch controller board • Connector check • Board check

• Code: ED12
• Description: Shutter home position error: The shutter is not at the home position. [MJ-1103/1104]
• Causes: Shutter opening/closing sensor (S4) Shutter clutch (CLT1) Finisher controller board
• Remedy: Shutter • Open and close the shutter. If there is any mechanical problem, fix its mechanism. Shutter opening/closing sensor (S4) • Rotate sideways adjustment motor and fix its mechanism if it does not rotate smoothly. • Motor check • Connector check • Harness check Shutter clutch (CLT1) • Clutch check • Connector check • Harness check Finisher controller board • Connector check • Board check

• Code: ED13
• Description: Front alignment plate home position error: The front alignment plate is not at the home position. [MJ1103/1104]
• Causes: Front alignment plate home position sensor (S7) Front alignment motor (M9) Finisher controller board
• Remedy: Front alignment plate • Move the front alignment plate. If there is any mechanical problem, fix its mechanism. Front alignment plate home position sensor (S7) • Sensor check • Connector check • Harness check Front alignment motor (M9) • Motor check • Connector check • Harness check Finisher controller board • Connector check • Board check

• Code: ED14
• Description: Rear alignment plate home position error: The rear alignment plate is not at the home position. [MJ1103/1104]
• Causes: Rear alignment plate home position sensor (S7) Rear alignment motor (M10) Finisher controller board
• Remedy: Rear alignment plate • Move the rear alignment plate. If there is any mechanical problem, fix its mechanism. Rear alignment plate home position sensor (S7) • Sensor check • Connector check • Harness check Rear alignment motor (M9) • Motor check • Connector check • Harness check Finisher controller board • Connector check • Board check

• Code: ED15
• Description: Paddle home position error: The paddle is not at the home position. [MJ-1103/1104]
• Causes: Paddle home position sensor (S3) Paddle motor (M8) Finisher controller board
• Remedy: Paddle • Rotate the paddle. If there is any mechanical problem, fix its mechanism. Paddle home position sensor (S3) • Sensor check • Connector check • Harness check Paddle motor (M8) • Motor check • Connector check • Harness check Finisher controller board • Connector check • Board check

• Code: ED16
• Description: Buffer tray home position error: The buffer tray is not at the home position. [MJ-1103/1104]
• Causes: Buffer tray home position sensor (S5) Buffer tray guide motor (M3) Finisher controller board
• Remedy: Buffer tray guide • Open and close the buffer tray guide. If there is any mechanical problem, fix its mechanism. Buffer tray home position sensor (S5) • Sensor check • Connector check • Harness check Buffer tray guide motor (M3) • Motor check • Connector check • Harness check Finisher controller board • Connector check • Board check