Description: Media sensor output abnormality during paper passing: The sensor output value while paper is being passed is not normal.
Causes: Media sensor (S69)
Remedy: 1 If these codes are recorded in the error history, the media sensor may have a malfunction. In this case check the following: 2 Is the connector of the media sensor disconnected or is any harness open circuited? 3 Are the arm of the media sensor and the bearing rollers operating properly? 4 Is the media sensor adjusted correctly? 6.7.1Adjustment of the media sensor position 5 If any abnormality was found in step 3 above or no abnormality was found in steps 2 and 4, replace the media sensor. Note that printing is available even if the media sensor is in a faulty condition. The functions that the media sensor usually performs are then carried out as follows: If the media type of paper is set as plain paper, a media type (plain paper 1 or 2) set in advance in the code below will be used. 08-4599 0: Plain paper 1 1: Plain paper 2 (Factory default - JPD: 0, overseas: 1) Media type setting checking function will be disabled. Even if the media sensor is in a faulty condition, any message notifying this will not be appear. Check the condition with the error history.
Code: E010
Description: Jam not reaching the fuser transport sensor The paper which has passed through the fuser unit does not reach the fuser transport sensor.
Causes: Fuser transport sensor LGC board ADU board PFC board Fuser unit
Remedy: ADU board • Connector check (CN491, CN497) • Board check Fuser transport sensor • Sensor check (Perform the input check: 03-[ALL]OFF/[2]/[C], 03- [COPY]ON/[5]/[F]) • Connector check • Harness check LGC board • Connector check (CN309) • Harness check • Board check Fuser unit • Check the gap between the separation plate and the fuser belt. (Refer to “6.7.4 Gap adjustment for separation plate”.) • Paper transport check Drive unit, Rollers • Gear check • Roller check Leading edge margin Adjust the margin with 05-4402 (Leading edge position adjustment) to “Color: 5.5 mm”. (Specification Black: 4.2 mm / Color: 5 mm) • Use A3/LD paper • Black solid image on 10 mm of the leading edge Refer to “6.1.1 Image Related Adjustment”. 2nd transfer bias offset Change the 2nd transfer bias offset value as shown below and then check if there are still jams. Change the default value 5 of each code below to 6 or 7. Color: 05-2934 Subcode: 0, 7 Color: 05-2935 Subcode: 0, 7 Black: 05-2936 Subcode: 0, 7 Black: 05-2937 Subcode: 0, 7 Change of the 2nd transfer bias If the leading edge of paper clings to the 2nd transfer roller and causes paper jamming, change the 2nd transfer roller bias correction factor of the leading/trailing edge of the paper. (The larger the value, the smaller the transfer voltage of the leading/trailing edge of the paper.) Codes to be changed (Initial value of the transfer bias of the leading/trailing edge of the paper: 0) • Color mode print (top side): 05-2938-* • Color mode print (back side): 05-2939-* • Black mode print (top side): 05-2940-* • Black mode print (back side): 05-2941-* Sub codes:* → Plain paper: 0, Recycled paper: 7 Notes: After these codes are changed, perform solid duplexprinting and check that there is no faint or void image on the leading/trailing edge of the paper. PFC board • Connector check (CN500, CN511) • Harness check • Board check
Code: E011
Description: Transfer belt paper-clinging jam: The paper after the 2nd transfer is clinging to the transfer belt, or a paper jam occurred between the registration roller and the paper clinging detection sensor.
Causes: Paper clinging detection sensor Registration motor PFC board LGC board Rollers
Remedy: Paper clinging detection sensor • Sensor check (Perform the input check: 03-[ALL]OFF/[9]/[D]) • Connector check • Harness check Registration motor • Motor check (Perform the output check: 03-128/528) • Connector check • Harness check PFC board • Connector check (CN514, CN515) • Board check LGC board • Connector check (CN537, CN538, CN539) • Board check Drive unit, Rollers • Gear check • Roller check Setting If jams occur on the back side in duplex printing, change the media type mode to the recycled paper mode, and then check if there are still jams. (When this type of jam occurs on heavily curled paper during duplex printing, the jam may be resolved by selecting the recycled paper mode.) 2nd transfer bias offset Change the 2nd transfer bias offset value as shown below and then check if there are still jams. Change the default value 5 of each code below to 6 or 7. Color: 05-2934 Subcode: 0, 7 Color: 05-2935 Subcode: 0, 7 Black: 05-2936 Subcode: 0, 7 Black: 05-2937 Subcode: 0, 7 Change of the 2nd transfer bias If the leading edge of paper clings to the 2nd transfer roller and causes paper jamming, change the 2nd transfer roller bias correction factor of the leading/trailing edge of the paper. (The larger the value, the smaller the transfer voltage of the leading/trailing edge of the paper.) Codes to be changed (Initial value of the transfer bias of the leading/trailing edge of the paper: 0) • Color mode print (top side): 05-2938-* • Color mode print (back side): 05-2939-* • Black mode print (top side): 05-2940-* • Black mode print (back side): 05-2941-* Sub codes:* → Plain paper: 0, Recycled paper: 7 Notes: After these codes are changed, perform solid duplexprinting and check that there is no faint or void image on the leading/trailing edge of the paper. Other Check if there is any paper clinging to the transfer belt or entering under the receiving tray. Remove it if there is. Use the paper within the specification if the thin paper being used is out of specification.
Code: E020
Description: Stop jam at the fuser transport sensor: The trailing edge of the paper does not pass the fuser transport sensor after its leading edge has reached this sensor.
Description: Incorrect paper size setting for 1st drawer: The size of paper in the 1st drawer differs from size setting of the equipment.
Causes:
Remedy: If any paper remains in the equipment or drawer, remove it. Match the paper size of the drawer setting and the one in the drawer. Paper size detection is performed at the first sheet of paper when the drawer is opened or closed, or when the power of the equipment is turned ON.
Code: E062
Description: Incorrect paper size setting for 2nd drawer: The size of paper in the 2nd drawer differs from size setting of the equipment.
Causes:
Remedy: If any paper remains in the equipment or drawer, remove it. Match the paper size of the drawer setting and the one in the drawer. Paper size detection is performed at the first sheet of paper when the drawer is opened or closed, or when the power of the equipment is turned ON.
Code: E063
Description: Incorrect paper size setting for 3rd drawer: The size of paper in the 3rd drawer differs from size setting of the equipment.
Causes:
Remedy: If any paper remains in the equipment or drawer, remove it. Match the paper size of the drawer setting and the one in the drawer. Paper size detection is performed at the first sheet of paper when the drawer is opened or closed, or when the power of the equipment is turned ON.
Máy Photocopy
Máy in mã vạch - In tem nhãn
PC- Laptop - Điện thoại
Máy in – Mực in
Máy chiếu - Màn chiếu
Máy chấm công - Kiểm soát ra vào
Máy hủy tài liệu
Máy đếm tiền, kho , quỹ
Loa - Loa bluetooth, vi tính, Karaok
Máy lạnh, Cây nước nóng lạnh
