Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Toshiba e-Studio 6570C — Trang 18/44

Code: CE60

Description: Drum thermistor-Y abnormality: The output value of the drum thermistor-Y is out of a specified range.
Causes: Drum thermistor-K Drum thermistor-Y EPU board LGC board
Remedy: EPU tray (process unit) • Connection check (05-2788) • Connector check(CN551, CN553, CN556) • Harness check Drum thermistor-K (THM1) • Sensor check (Perform the input check: 03-[ALL]OFF/[3]) • Connector check • Harness check Drum thermistor-Y (THM2) • Sensor check (Perform the input check: 03-[ALL]OFF/[4]) • Connector check • Harness check LGC board • Connector check (CN308) • Harness check

Code: CE71

Description: Drum phase adjustment abnormality: Drum phase sensors (Color drum phase sensor and K drum phase sensor) are not turned ON after the drum motor was rotated for a specified period of time.
Causes: Drum motor (K) Drum motor (YMC) K drum phase sensor Color drum phase sensor LGC board Cleaning blade (Y, M, C, K) Needle electrode Drum (Y, M, C, K)
Remedy: LGC board • Connector check (CN313, CN315) Drum motor (K) (M27) • Motor check (Perform the output check: 03-110) • Connector check • Harness check Drum motor (YMC) (M28) • Motor check (Perform the output check: 03-110) • Connector check • Driving section check (Is there any abnormality on the rotation?) • Harness check K drum phase sensor (S44) • Sensor check (Perform the input check: 03-[ALL]OFF/[9]/B) • Connector check • Harness check Color drum phase sensor (S43) • Sensor check (Perform the input check: 03-[ALL]OFF/[9]/A) • Connector check • Harness check Drum cleaner unit (Y, M, C, K) • Cleaning blade check (Check if it turns up.) Main charger unit • Needle electrode check Drum (Y, M, C, K) • Drum check (Check if the aluminum section of the drum flange is worn out.)

Code: CE90

Description: Drum thermistor-K abnormality: The output value of the drum thermistor-K is out of a specified range
Causes: Drum thermistor-K Drum thermistor-Y EPU board LGC board
Remedy: EPU tray (process unit) • Connection check (05-2788) • Connector check(CN551, CN553, CN556) • Harness check Drum thermistor-K (THM1) • Sensor check (Perform the input check: 03-[ALL]OFF/[3]) • Connector check • Harness check Drum thermistor-Y (THM2) • Sensor check (Perform the input check: 03-[ALL]OFF/[4]) • Connector check • Harness check LGC board • Connector check (CN308) • Harness check

Code: CEC0

Description: 2nd transfer roller position detection abnormality: The 2nd transfer roller does not contact/release normally.
Causes: 2nd transfer roller position detection sensor 2nd transfer cam motor LGC board
Remedy: 2nd transfer cam motor (M48) • 2nd transfer cam motor check (Perform the output check: 243) • Connector check • Harness check 2nd transfer roller position detection sensor (S50) • Sensor check (Perform the input check: 03-[ALL]OFF/[9]/[H]) • Connector check • Harness check LGC board • Connector check (CN307, CN314) • Board check 2nd transfer contact/release cam unit gear • Check that it is not damaged. Actuator in the TRU • Check that it is installed properly. • Check that it is not damaged. Sensors in the TRU • Check that they are installed properly. • Check that the cam is not damaged.

Code: CEC5

Description: Incorrect cam position alarm during 2nd transfer
Causes: Actuator in the TRU Sensors in the TRU
Remedy: 1 2nd transfer contact/release cam unit gear Check that it is not damaged. 2 Actuator in the TRU • Check that it is installed properly. • Check that it is not damaged. 3 Sensors in the TRU • Check that they are installed properly. • Check that the cam is not damaged. 4 If any abnormality on a part is detected and the part is replaced, the 2nd transfer pressure reduction is enabled by changing the value of the setting codes as follows: 08-4663: 0 to 10: Pressure reduction disabled1: Pressure reduction enabled 08-4664: 3 to 0Resetting incorrect cam position error count Notes: Change the value of the following codes to disable the pressure reduction: 08-4663: 1 to 0 0: Pressure reduction disabled 1: Pressure reduction enabled 08-4664: 0, 1 or 2 to 3 Resetting incorrect cam position error count

Code: CF10

Description: Communication module SRAM reading failure
Causes: Finisher control PC board Hole punch control PC board (when MJ-6102 is installed)
Remedy: Equipment • Is the error recovered when the power of the equipment is turned OFF and then back ON? Setting • Check if the MJ-1103/1104 is set as the specified finisher on the equipment. (08-1912=”1”) Finisher control PC board (FIN) • Connector check • Board check Hole punch control PC board (HP) • Connector check (when MJ-6102 is installed) • Board check

Code: CF90

Description: Laser optical unit shutter abnormality.
Causes: Shutter motor Shutter sensor (home position) Shutter sensor (end position) LGC board
Remedy: Shutter motor (M38) Shutter • Motor check (Perform the output check: 03-201) • Connector check (CN213, CN214) • Harness check • Shutter plate check Shutter sensor (home position) (S24) • Sensor check (Perform the input check: 03-[ALL]OFF/[7]/[E]) • Connector check • Harness check Shutter sensor (end position) (S25) • Sensor check (Perform the input check: 03-[ALL]OFF/[7]/[D]) • Connector check • Harness check LGC board • Connector check (CN327) • +5V check (CN345-21pin) • Board check Other • Check if the equipment is grounded.

Code: CFA0

Description: Media sensor output abnormality before paper reaching: The sensor output value before paper is reached to the media sensor is not normal.
Causes: Media sensor (S69)
Remedy: 1 If these codes are recorded in the error history, the media sensor may have a malfunction. In this case check the following: 2 Is the connector of the media sensor disconnected or is any harness open circuited? 3 Are the arm of the media sensor and the bearing rollers operating properly? 4 Is the media sensor adjusted correctly? 6.7.1Adjustment of the media sensor position 5 If any abnormality was found in step 3 above or no abnormality was found in steps 2 and 4, replace the media sensor. Note that printing is available even if the media sensor is in a faulty condition. The functions that the media sensor usually performs are then carried out as follows: If the media type of paper is set as plain paper, a media type (plain paper 1 or 2) set in advance in the code below will be used. 08-4599 0: Plain paper 1 1: Plain paper 2 (Factory default - JPD: 0, overseas: 1) Media type setting checking function will be disabled. Even if the media sensor is in a faulty condition, any message notifying this will not be appear. Check the condition with the error history.
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie