• Code: 04-810-00
• Description: Rear Fan Failure
• Causes: The Rear Door Fan has failed.
• Remedy: • Close the Rear Door. • Check for obstructions blocking fan rotation.
  Cycle system power. The error message is displayed. Y↓ N→Perform SCP 6 Final Actions. Select dC330 code 10-500 to test the Rear Fan. The Fan rotates. Y↓ N→Replace the Fan, then retest. The Fan rotates. Y↓ N→Check the Rear Door connection P/J63. The connector is undamaged. Y↓ N→Repair or replace the Rear Door. Remove the Right Cover and check CN4 on the Joint Board. The connection is secure. Y↓ N→Secure the connections. Replace these components in order until the error is corrected. 1. Rear Door, PL 28.25 Item 1 2. Joint Board, PL 9.15 Item 7 3. Exit Assembly, PL 10.30 Item 25 Reassemble and perform SCP 6 Final Actions. Reassemble and perform SCP 6 Final Actions.

• Code: 04-930-00
• Description: Main Fan Failure
• Causes: The SMPS Fan has failed.
• Remedy: • Check for obstructions blocking fan rotation.
  Cycle system power. The error message is displayed. Y↓ N→Perform SCP 6 Final Actions. Select dC330 code 04-120 to test the SMPS Fan. The Fan rotates. Y↓ N→Replace the Fan, then retest. The Fan rotates. Y↓ N→Remove the Left Cover and check CN1 on the Joint Board. The connection is secure. Y↓ N→Secure the connections. Replace these components in order until the error is corrected. 1. SMPS Fan, PL 1.15 Item 6 2. Joint Board, PL 9.15 Item 7 Reassemble and perform SCP 6 Final Actions. Reassemble and perform SCP 6 Final Actions.

• Code: 06-100-00, 06-200-00
• Description: LSU Error
• Causes: 06-100-00 The Laser Unit has failed. The Laser Unit did not reach ready within a defined time. 06-200-00 LSU Hsync Error. The Laser Unit has failed.
• Remedy: • Cycle system power.
  The error message is displayed. Y↓ N→Perform SCP 6 Final Actions. Select dC330 code 06-100 to test the Laser Unit. The Laser Unit is operational (on/off). Y↓ N→Replace the Laser Unit , then retest. The Laser Unit is operational. Y↓ N→Replace the IP Board . Reassemble and perform SCP 6 Final Actions. Reassemble and perform SCP 6 Final Actions.

• Code: 07-110-00
• Description: Paper Empty at Tray 2
• Causes: The Tray 2 No Paper indicates the Tray is empty.
• Remedy: 1. Add media to the Tray. 2. Check the No Paper Sensor Actuator. 3. Check for obstruction of the Pick mechanism.
  Check the Tray 2 No Paper Sensor Actuator. The actuator is undamaged and motion is good. Y↓ N→Repair or replace the Tray 2 No Paper Sensor Actuator. Select dC330 code 07-210 to test the sensor. The sensor signal changes (high/low). Y↓ N→Replace the Tray 2 No Paper Sensor (PL 8.15 Item 19), then retest. The sensor signal changes. Y↓ N→Remove the Right Cover and reseat CN12 on the MCU Board, then retest. The sensor signal changes. Y↓ N→Replace the MCU Board. Reassemble and perform SCP 6 Final Actions. Reassemble and perform SCP 6 Final Actions. Reassemble and perform SCP 6 Final Actions.

• Code: 07-120-00
• Description: Tray 2 is Open
• Causes: The Size Switch indicates the Tray is not fully installed.
• Remedy: 1. Close the Tray. 2. Check the Size Switch.
  Cycle system power. The error message is displayed. Y↓ N→Complete. Remove Tray 2 and inspect the Size Switch. The Size Switch is undamaged. Y↓ N→Replace the Size Switch, then retest. Select dC330 code 07-200 to test the switch. The switch signals change (open/closed). Y↓ N→Remove the Right Cover and reseat CN11 on the MCU Board, then retest. The sensor signal changes. Y↓ N→Replace the MCU Board. Replace these components in order until the error is corrected. 1. Size Switch, PL 3.10 Item 9 2. MCU Board, PL 3.10 Item 3

• Code: 07-130-00
• Description: Jam 0 in Tray 2
• Causes: Media present at the Take Away Sensor.
• Remedy: 1. Check media condition. 2. Check for obstructions in the media path.
  Check the Nudger, Feed, and Separator Rollers for excessive wear or contamination. The rollers are undamaged and clean. Y↓ N→Clean or replace the rollers. Check for obstructions or debris in the media path. The media path is clear. Y↓ N→Clear the media path of obstructions or debris. Check Tray 2 pick assembly (PL 8.15) motion. Pick assembly motion is good. Y↓ N→Repair improper pick assembly motion. Select dC330 code 08-820 to test the Feed Clutch. The clutch is engaged (on/off). Y↓ N→Remove the Right Cover and reseat CN12 on the MCU Board, then retest. The clutch is engaged. Y↓ N→Replace the Feed Clutch. Reassemble and perform SCP 6 Final Actions. Select dC330 code 04-580 to test the Feed Drive Assembly. The Feed Drive Assembly rotates (on/off). Y↓ N→Remove the Right Cover and reseat CN12 on the MCU Board, then retest. The Feed Drive Assembly rotates. Y↓ N→Replace the Feed Drive Assembly. Reassemble and perform SCP 6 Final Actions. Replace the MCU Board.

• Code: 07-210-00
• Description: Paper Empty at Tray 3
• Causes: The Tray 3 No Paper indicates the Tray is empty.
• Remedy: 1. Add media to the Tray. 2. Check the No Paper Sensor Actuator. 3. Check for obstruction of the Pick mechanism.
  Check the Tray 3 No Paper Sensor Actuator. The actuator is undamaged and motion is good. Y↓ N→Repair or replace the Tray 3 No Paper Sensor Actuator. Select dC330 code 07-310 to test the sensor. The sensor signal changes (high/low). Y↓ N→Remove the IOT, from the Feeder and check the Upper Option Harness, PL 8.30 Item 10. The harness is undamaged. Y↓ N→Replace the harness. Check the IOT Lower Option Harness. The harness is undamaged. Y↓ N→Replace the IOT Lower Option Harness. Replace the Tray 3 No Paper Sensor , then retest. The sensor signal changes. Y↓ N→Remove the Right Cover and reseat CN3 on the Feeder Board, then retest. The sensor signal changes. Y↓ N→Replace the MCU Board. Reassemble and perform SCP 6 Final Actions. Reassemble and perform SCP 6 Final Actions. Replace the MCU Board.

• Code: 07-220-00
• Description: Tray 3 is Open
• Causes: The Size Switch indicates the Tray is not fully installed.
• Remedy: 1. Close the Tray. 2. Check the Size Switch.
  Cycle system power. The error message is displayed. Y↓ N→Complete. Remove Tray 3 and inspect the Size Switch. The Size Switch is undamaged. Y↓ N→Replace the Size Switch, then retest. Select dC330 code 07-300 to test the switch. The switch signals change (open/closed). Y↓ N→Remove the Right Cover and reseat CN5 on the Feeder Board, then retest. The sensor signal changes. Y↓ N→Replace the Feeder Board. Reassemble and perform SCP 6 Final Actions. Replace these components in order until the error is corrected. 1. Size Switch, PL 8.30 Item 9 2. Feeder Board, PL 8.30 Item 7 3. MCU Board, PL 3.10 Item 3