Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Xerox WorkCentre 3615 — Trang 19/33

Code: 062-277 ... 062-393

Description: 062-277: IIT internal communication error. 062-311: IIT failure initialization error. 062-317: Interference buffer full was detected at the time of DADF scan. 062-318: A Scan setup did not meet the deadline into Page Gap. 062-319: A PLL lock was not carried out before 1stScan start, but the lock has separated during continuation. 062-320: Scanning error. 062-321: Unexecutable error. (carriage is at the locked position, etc.) 062-322: Parameter error. 062-360: Carriage home position error. 062-371: IIT failure Lamp error. 062-393: CCD ASIC communication error.
Remedy: 062-277/062-311/062-317/062-318/062-319/062-321/062-322/062-360/062-371/062-393: • Turn the power Off and On to check that the error recurs. Then proceed to the FIP. 062-320: 1. Check the file data in the printer. Print or clear the stored files and data at the printer memory. 2. Perform a black and white scan. 3. If the error occurs again, proceed to the FIP.
1 Check the connection between the IIT ASSEMBLY and the ESS PWB. • Are the P/J451 and the P/J452 connected securely? Go to Step 2. Connect that P/J451 and P/J452 are secure 2 • Replace (IIT Assembly). • Does an error occur? Replace (ESS PWB) Troubleshooting complete.

Code: 062-316

Description: DADF Motor Fail Cause: Detect DADF Motor Fail.
Remedy: 1 Are there any foreign substances in the DADF Motor Drive Section? Remove the foreign substances. Go to Step 2. 2 Check the connection between the DADF ASSEMBLY and the ESS PWB. • Is the P/J453 connected securely? Go to Step 3. Connect P/J453 securely 3 • Replace (DADF). • Does an error occur? Replace (ESS PWB). Troubleshooting complete.

Code: 062-790

Description: Copy Limit Cause: Copy Limit.
Remedy: The machine will recover after the Enter Key is pressed or message is displayed for 60 seconds. If the error persists: 1. Change your original. 2. Ensure that the error is replicated after the printer is powered Off and then On, and then replace (ESS PWB).

Code: 071-100

Description: IOT Tray1 Misfeed Jam 050-134 is displayed in the UI. Cause: After the Tray 1 Feed Clutch turned ON, the Regi. Sensor did not turn ON within the specified time.
Remedy: 1 Is there any foreign substances or bits of paper found on the paper transport path? Remove the foreign substances and bits of paper, etc. Go to Step 2. 2 Are the paper feed rolls installed properly? Go to Step 3. Reinstall the corresponding paper feed rolls 3 Are the paper feed rolls deformed or worn out? Replace the corresponding paper feed rolls Go to Step 4. 4 • Execute the Diag Digital Input [071-102] to check the operation of the Regi. Sensor HVPS. • Is the Regi. Sensor HVPS operating normally? Go to Step 5. Go to FIP 2.03 5 • Execute the Diag Digital Output [071-005] to check the operation of the CST FEED CLUTCH. • Is the CST FEED CLUTCH operating properly? Go to Step 6. Go to FIP 2.11 6 • Execute the Diag Digital Output [071-001] to check the rotation of the MAIN DRIVE ASSEMBLY. • Is it working properly? Replace (MCU PWB) Go to FIP 2.15

Code: 071-920

Description: Waiting to Print Side 2 Load Printed Pages into the NNN Cause: Waiting for side 2 to be set for manual duplex print (Tray).
Remedy: Set the Paper correctly. Press OK button within the specified time.

Code: 071-921

Description: Manual Duplex Print Cause: Waiting for Set key to be pressed after setting side 2 for manual duplex print (Tray).
Remedy: Set the Paper correctly. Press OK button within the specified time.

Code: 072-100, 073-100, 074-100

Description: 072-100 IOT Tray2 Misfeed Jam 073-100 IOT Tray3 Misfeed Jam 074-100 IOT Tray4 Misfeed Jam Cause: 072-100: 050-139 is displayed in the UI. After the Tray 2 Feed Clutch turned ON, the Tray 2 Path Sensor did not turn ON within the specified time. 073-100: 050-140 is displayed in the UI. After the Tray 3 Feed Clutch turned ON, the Tray 3 Path Sensor did not turn ON within the specified time. 074-100: 050-141 is displayed in the UI. After the Tray 4 Feed Clutch turned ON, the Tray 4 Path Sensor did not turn ON within the specified time.
Remedy: 1 Is there any foreign substances or bits of paper found on the paper transport path? Remove the foreign substances and bits of paper, etc. Go to Step 2. 2 Are the paper feed rolls installed properly? Go to Step 3. Reinstall the corresponding paper feed rolls 3 Are the paper feed rolls deformed or worn out? Replace the corresponding paper feed rolls Go to Step 4. 4 • Execute the Diag Digital Input Tray 2: 071- 119 / Tray 3:071-120 / Tray 4:071-121 to check the operation of the Path Sensor. • Is the Path Sensor operating normally? Go to Step 5. Go to FIP 2.07 5 • Execute the Diag Digital Output Tray 2: 071-018 / Tray 3:071-019 / Tray 4:071-020 to check the operation of the OPTIONAL FEEDER CLUTCH ASSEMBLY. • Is the OPTIONAL FEEDER CLUTCH ASSEMBLY operating normally? Go to Step 6. Go to FIP 2.12 6 • Execute the Diag Digital Output Tray 2: 071-009 / Tray 3:071-012 / Tray 4:071-015 to check the rotation of the MOTORASSEMBLY OPTION. • Is it working properly? Go to Step 7. Go to FIP 2.17 7 • Replace (Feeder Assembly). • Does an error occur? Replace (MCU PWB) Troubleshooting complete.

Code: 072-101, 073-101

Description: 072-101 IOT Path 2 SNS On Jam 073-101 IOT Path 3 SNS On Jam Cause: 072-101: 050-136 is displayed in the UI. The Tray 2 Path Sensor did not turn ON within the specified time after the Tray 3 Path Sensor turned ON. 073-101: 050-135 is displayed in the UI. The Tray 3 Path Sensor did not turn ON within the specified time after the Tray 4 Path Sensor turned ON.
Remedy: 1 Is there any foreign substances or bits of paper found on the paper transport path? Remove the foreign substances and bits of paper, etc. Go to Step 2. 2 Are the paper feed rolls installed properly? Go to Step 3. Reinstall the corresponding paper feed rolls 3 Are the paper feed rolls deformed or worn out? Replace the corresponding paper feed rolls Go to Step 4. 4 • Execute the Diag Digital Input Tray 2: 071- 119 / Tray 3:071-120 / Tray 4:071-121 to check the operation of the Path Sensor. • Is the Path Sensor operating normally? Go to Step 5. Go to FIP 2.07 5 • Execute the Diag Digital Output Tray 2: 071-018 / Tray 3:071-019 / Tray 4:071-020 to check the operation of the OPTIONAL FEEDER CLUTCH ASSEMBLY. • Is the OPTIONAL FEEDER CLUTCH ASSEMBLY operating normally? Go to Step 6. Go to FIP 2.13 6 • Execute the Diag Digital Output Tray 2: 071-009 / Tray 3:071-012 / Tray 4:071-015 to check the rotation of the OPTIONAL TRAY MOTOR-ASSEMBLY. • Is it working properly? Go to Step 7. Go to FIP 2.17 7 • Replace (Feeder Assembly). • Does an error occur? Replace (MCU PWB) Troubleshooting complete.
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie