• Code: 05A
• Description: Document Not Sensed in DADF RAP Use this RAP if the machine fails to detect a document in the DADF.
• Remedy: 1. Refer to Wiring Diagram 11. Perform the following: a. Check that the document detect sensor actuator, PL 5.20 Item 17 moves freely and is not damaged. If necessary, install a document detect sensor actuator, PL 5.20 Item 17. b. Enter dC330 code 05-100. Check the document detect sensor (Q05-100), PL 5.20 Item 13. c. Check the wiring between the document detect sensor and CN4 on the DADF Sensor PWB. If necessary, install a new document detect sensor, PL 5.20 Item 13. d. Check the wiring between CN1 on the DADF Sensor PWB and CN3 on the DADF PWB. 2. Refer to Wiring Diagram 9. Perform the following: a. Check that the platen cover sensor actuator, PL 14.10 Item 12 moves freely and is not damaged. b. Enter dC330 code 05-400. Check the platen cover sensor (Q05-400), PL 14.10 Item 14. c. Check the wiring between the platen cover sensor and CN3 on the Scanner PWB. If necessary, install a new platen cover sensor, PL 14.10 Item 12.

• Code: 06-100, 06-200
• Description: LSU Error RAP 06-100 The machine has detected that the LSU did not reach a ready state within the correct time. 06-200 The machine did not detect the laser beam within the correct time.
• Remedy: 1. Switch off the machine, then switch on the machine. 2. Enter dC330 codes 06-100 and 06-110. Check that the LSU motor is up to the required speed. 3. Check the wiring between the LSU and CN5 on the Main PWB. 4. Install new components as necessary: • LSU, PL 6.10 Item 1. • Main PWB, PL 1.10 Item 1.

• Code: 07-100
• Description: Tray 1 Paper Low RAP 07-100 The machine has detected that tray 1 is nearly empty.
• Remedy: 1. Make sure tray 1 is fully home. 2. Pull out tray 1. Check for obstructions behind the tray. 3. Check the tray elevator mechanism on the back of tray 1. 4. Check that the tray 1 paper low sensor actuator on the tray elevator gear, PL 7.10 Item 24 is not missing or damaged. 5. Replace tray 1. Listen for the tray elevating motor to raise the knock-up plate. If the plate does not rise, check the wiring between the tray 1 elevating motor and CN19 on the Main PWB. If necessary, install new components: • Tray 1 elevating motor, PL 7.15 Item 8. • Tray feed assembly, PL 8.10 Item 1. 6. Enter dC330 code 07-160. Check the tray 1 paper low sensor (Q07-160), PL 7.15 Item 2. 7. Check the wiring between the tray 1 paper low sensor and CN15 on the Main PWB. If necessary, install a new tray 1 paper low sensor, PL 7.15 Item 2. 8. If necessary, install new components: • Main PWB, PL 1.10 Item 1. • Tray 1 cassette assembly, PL 7.10 Item 1.

• Code: 07-110
• Description: Paper Empty at Tray 1 RAP 07-110 The machine has detected that tray 1 is empty.
• Remedy: 1. Remove tray 1. Check that the tray 1 paper empty sensor actuator, PL 8.10 Item 4 moves freely and is not damaged. 2. Replace tray 1. Listen for the tray elevator to raise the knock-up plate. If the plate does not rise, check the wiring between the tray 1 elevator motor and CN19 on the Main PWB. If necessary, install new components: • Tray 1 elevator motor, PL 7.15 Item 8. • Tray feed assembly, PL 8.10 Item 1. 3. Enter dC330 code 07-110. Check the tray 1 paper empty sensor (S07-110), PL 8.10 Item 2. 4. Check the wiring between the tray 1 paper empty sensor and CN19 on the Main PWB. If necessary, install a new tray 1 paper empty sensor, PL 8.10 Item 2. 5. If necessary, install new components: • Tray 1 feed assembly, PL 8.10 Item 1. • Main PWB, PL 1.10 Item 1.

• Code: 07-120
• Description: Tray 1 Cassette Out RAP 07-120 The machine has detected that tray 1 is not home.
• Remedy: 1. Make sure tray 1 is fully home. 2. Pull out tray 1. Check for obstructions behind the tray. 3. Check that the tray 1 home position sensor actuator on the back of the tray is not missing or damaged. 4. Enter dC330 code 07-100. Check the tray 1 home position sensor (Q07-100), PL 7.15 Item 2. 5. Check the wiring between the tray 1 home position sensor and CN15 on the Main PWB. If necessary, install a new tray 1 home position sensor, PL 7.15 Item 2. 6. If necessary, install a new main PWB, PL 1.10 Item 1.

• Code: 07-130
• Description: Jam 0 From Tray 1 RAP 07-130 The lead edge of the paper failed to actuate the registration sensor within the correct time after paper was fed from tray 1.
• Remedy: 1. Pull out tray 1. Remove all jammed paper. 2. Check the paper path for damage or obstructions. 3. Check that the registration sensor actuator, PL 8.15 Item 4 moves freely and is not damaged. If necessary, install a new registration sensor actuator assembly, PL 8.15 Item 13. 4. Enter dC330 code 08-500. Check the registration sensor (Q08-500), PL 8.15 Item 8. 5. Check the wiring between the registration sensor and CN13 on the Main PWB. If necessary, install a new registration sensor, PL 8.15 Item 8. 6. Check that the feed sensor actuator, PL 8.15 Item 5 moves freely and is not damaged. If necessary, install a new feed sensor actuator assembly, PL 8.15 Item 14. 7. Enter dC330 code 08-100. Check the feed sensor (Q08-100), PL 8.15 Item 8. 8. Check the wiring between the feed sensor and CN13 on the Main PWB. If necessary, install a new feed sensor, PL 8.15 Item 8. 9. Enter dC330 code 04-100 to run the main BLDC motor. 10. While the main BLDC motor runs, stack the code 08-810 to energize the tray 1 pickup clutch (CL08-810). Check that the tray 1 feed roll, PL 8.10 Item 12 rotates. 11. Check the wiring between the tray 1 pickup clutch and CN13 on the Main PWB. Install new components as necessary, PL 4.20, PL 7.15 and PL 8.10. 12. While the main BLDC motor runs, stack the code 08-850 to energize the registration clutch (CL08-850). Check that the registration roll, PL 4.15 Item 1 rotates. 13. Check the wiring between the registration clutch and CN13 on the Main PWB. Install new components as necessary, PL 4.15 and PL 4.20. 14. Check that the following components are clean and rotate freely, install new components as necessary: • Tray 1 feed roll, PL 8.10 Item 12. • Tray 1 nudger roll, PL 8.10 Item 12. • Tray 1 retard roll, PL 7.15 Item 20. • Registration roll, PL 4.15 Item 1. • Registration roll idler, PL 4.15 Item 7. 15. If necessary, install new components: • Tray feed assembly, PL 8.10 Item 1. • Main PWB, PL 1.10 Item 1.

• Code: 07-200, 07-300, 07-400
• Description: Tray 2, 3 or 4 Paper Low RAP 07-200 The machine has detected that tray 2 is nearly empty when the tray is full. 07-300 The machine has detected that tray 3 is nearly empty when the tray is full. 07-400 The machine has detected that tray 4 is nearly empty when the tray is full.
• Remedy: 1. Make sure the tray is fully home. 2. Pull out the tray. Check for obstructions behind the tray. 3. Check the tray elevator mechanism on the back of the tray. 4. Check that the paper low sensor actuator on the tray elevator gear, PL 7.10 Item 24 is not missing or damaged. 5. Replace the tray. Listen for the tray elevating motor to raise the knock-up plate. If the plate does not rise, check the wiring between the tray elevating motor and CN7 on the Tray PWB. If necessary, install new components: • Tray elevating motor, PL 7.20 Item 7. • Tray feed assembly, PL 8.10 Item 1. 6. Enter dC330. Check the relevant paper low sensor, PL 7.20 Item 3: • Tray 2. Code 07-260. • Tray 3. Code 07-360. • Tray 4. Code 07-460. 7. Check the wiring between the paper low sensor and CN5 on the Tray PWB. If necessary, install a new paper low sensor, PL 7.20 Item 3. 8. Check the wiring between CN1 on the Tray PWB and CN24 on the Main PWB. 9. If necessary, install new components: • Tray PWB, PL 7.20 Item 6. • Main PWB, PL 1.10 Item 1. • Tray cassette, PL 7.10 Item 1.

• Code: 07-210, 07-310, 07-410
• Description: Paper Empty at Tray 2, 3 or 4 RAP 07-210 The machine has detected that tray 2 is empty when the tray is full. 07-310 The machine has detected that tray 3 is empty when the tray is full. 07-410 The machine has detected that tray 4 is empty when the tray is full.
• Remedy: 1. Pull out the tray. Check that the paper empty actuator, PL 8.10 Item 4 moves freely and is not damaged. 2. Replace the tray. Listen for the tray elevating motor to raise the knock-up plate. If the plate does not rise, check the wiring between the tray elevating motor and CN7 on the Tray PWB. If necessary, install new components: • Tray elevating motor, PL 7.20 Item 7. • Tray feed assembly, PL 8.10 Item 1. 3. Enter dC330. Check the relevant paper empty sensor, PL 8.10 Item 2: • Tray 2. Code 07-210. • Tray 3. Code 07-310. • Tray 4. Code 07-410. 4. Check the wiring between the paper empty sensor and CN7 on the Tray PWB. If necessary, install a new paper empty sensor, PL 8.10 Item 2. 5. Check the wiring between CN1 on the Tray PWB and CN24 on the Main PWB. 6. If necessary, install new components: • Tray PWB, PL 7.20 Item 6. • Main PWB, PL 1.10 Item 1.