• Code: 07-220, 07-320, 07-420
• Description: Tray 2, 3 or 4 Cassette Out RAP 07-220 The machine has detected that tray 2 is not home. 07-320 The machine has detected that tray 3 is not home. 07-420 The machine has detected that tray 4 is not home.
• Remedy: 1. Make sure that the tray is fully home. 2. Pull out the tray. Check for obstructions behind the tray. 3. Check that the tray home position sensor actuator on the back of the tray is not missing or damaged. 4. Enter dC330. Check the relevant tray home position sensor, PL 7.20 Item 3: • Tray 2. Code 07-200. • Tray 3. Code 07-300. • Tray 4. Code 07-400. 5. Check the wiring between the tray home position sensor and CN6 on the Tray PWB. If necessary, install a new tray home position sensor, PL 7.20 Item 3. 6. Check the wiring between CN1 on the Tray PWB and CN24 on the Main PWB. 7. If necessary, install new components: • Tray PWB, PL 7.20 Item 6. • Main PWB, PL 1.10 Item 1.

• Code: 07-230, 07-330, 07-430
• Description: Jam 0 From Tray 2, 3 or 4 RAP 07-230 The lead edge of the paper failed to actuate the registration sensor within the correct time after paper was fed from tray 2. 07-330 The lead edge of the paper failed to actuate the registration sensor within the correct time after paper was fed from tray 3. 07-430 The lead edge of the paper failed to actuate the registration sensor within the correct time after paper was fed from tray 4.
• Remedy: 1. Pull out the tray. Remove all jammed paper. 2. Open the tray access door, PL 7.20 Item 18. Remove all jammed paper. 3. Check the paper path for damage or obstructions. 4. Check that the registration sensor actuator, PL 8.15 Item 4 moves freely and is not damaged. If necessary, install a new registration sensor actuator assembly, PL 8.15 Item 13. 5. Enter dC330 code 08-500. Check the registration sensor (Q08-500), PL 8.15 Item 8. 6. Check the wiring between the registration sensor and CN13 on the Main PWB. If necessary, install a new registration sensor, PL 8.15 Item 8. 7. Check that the tray feed sensor actuator, PL 7.25 Item 16 moves freely and is not damaged. 8. Enter dC330. Check the relevant tray feed sensor, PL 7.25 Item 14: • Tray 2. Code 08-200. • Tray 3. Code 08-300. • Tray 4. Code 08-400. 9. Check the wiring between the tray feed sensor and CN10 on the Tray PWB. If necessary, install a new feed sensor, PL 7.25 Item 14. 10. Enter dC330 code. Check that the relevant tray feed motor, PL 7.20 Item 9, runs and drives the tray transport roll, PL 7.25 Item 22: • Tray 2. Code 08-920. • Tray 3. Code 08-930. • Tray 4. Code 08-940. 11. Check the wiring between the tray feed motor and CN4 on the Tray PWB. 12. While the tray feed motor runs, stack the relevant code to energize the tray pickup clutch. Check that the tray feed roll, PL 7.25 Item 11 rotates: • Tray 2. Code 08-820. • Tray 3. Code 08-830. • Tray 4. Code 08-840. 13. Check the wiring between the tray pickup clutch and CN4 on the Tray PWB. 14. Check that the following components are clean and rotate freely: • Tray feed roll, PL 7.25 Item 11. • Tray nudger roll, PL 8.10 Item 12. • Tray retard roll, PL 8.10 Item 12. • Tray transport roll, PL 7.25 Item 22. • Tray transport roll idlers, part of the tray access door, PL 7.20 Item 18. 15. If necessary, install new components: • Tray feed roll, PL 7.25 Item 11. • Tray nudger roll, PL 8.10 Item 12. • Tray feed motor, PL 7.20 Item 9. • Tray PWB, PL 7.20 Item 6. • Tray assembly, PL 7.20 Item 1.

• Code: 07-231, 07-331, 07-431
• Description: Check the Tray Feed Area RAP 07-231 The machine has detected that paper is jammed in the tray 2 paper feeding area or the tray 2 side cover is open at power on. 07-331 The machine has detected that paper is jammed in the tray 3 paper feeding area or the tray 2 side cover is open at power on. 07-431 The machine has detected that paper is jammed in the tray 4 paper feeding area or the tray 2 side cover is open at power on.
• Remedy: 1. Pull out the tray. Remove all jammed paper. 2. Open the tray access door, PL 7.20 Item 18. Remove all jammed paper. 3. Check the paper path for damage or obstructions. 4. Check that the SCF door sensor actuator on the paper guide, PL 7.20 Item 13 is not missing or damaged. 5. Enter dC330. Check the relevant SCF door sensor, PL 7.25 Item 14: • Tray 2. Code 08-200. • Tray 3. Code 08-300. • Tray 4. Code 08-400. 6. Check the wiring between the SCF door sensor and CN10 on the Tray PWB. If necessary, install a new SCF door sensor, PL 7.25 Item 14. 7. Check the wiring between CN1 on the Tray PWB and CN24 on the Main PWB. 8. Check that the tray feed sensor actuator, PL 7.25 Item 16 moves freely and is not damaged. 9. Enter dC330. Check the relevant tray feed sensor, PL 7.25 Item 14: • Tray 2. Code 08-200. • Tray 3. Code 08-300. • Tray 4. Code 08-400. NOTE: The component control codes for the tray feed sensors are the same as for the SCF door sensors. 10. Check the wiring between the tray feed sensor and CN10 on the Tray PWB. If necessary, install a new feed sensor, PL 7.25 Item 14. 11. Enter dC330 code. Check that the relevant tray feed motor, PL 7.20 Item 9, runs and drives the tray transport roll, PL 7.25 Item 22: • Tray 2. Code 08-920. • Tray 3. Code 08-930. • Tray 4. Code 08-940. 12. Check the wiring between the tray feed motor and CN4 on the Tray PWB. 13. While the tray feed motor runs, stack the relevant code to energize the tray pickup clutch. Check that the tray feed roll, PL 7.25 Item 11 rotates: • Tray 2. Code 08-820. • Tray 3. Code 08-830. • Tray 4. Code 08-840. 14. Check the wiring between the tray pickup clutch, PL 7.25 Item 30 and CN4 on the Tray PWB. 15. Check that the following components are clean and rotate freely: • Tray feed roll, PL 7.25 Item 11. • Tray nudger roll, PL 8.10 Item 12. • Tray retard roll, PL 8.10 Item 12. • Tray transport roll, PL 7.25 Item 22. • Tray transport roll idlers, part of the tray access door, PL 7.20 Item 18. 16. If necessary, install new components: • Tray feed roll, PL 7.25 Item 11. • Tray nudger roll, PL 8.10 Item 12. • Tray feed motor, PL 7.20 Item 9. • Tray PWB, PL 7.20 Item 6. • Tray assembly, PL 7.20 Item 1.

• Code: 07-500
• Description: Paper Empty at Bypass Tray RAP 07-500 The machine has detected a failure to feed from the bypass tray.
• Remedy: 1. Open the right cover assembly, PL 7.30 Item 1. Check that the paper feed area at the bypass tray is clean. 2. Check the operation of the bypass paper empty sensor actuator, PL 8.20 Item 26. 3. Enter dC330 code 07-510. Check the bypass paper empty sensor (S07-510), PL 8.20 Item 26. 4. Check the wiring between the bypass paper empty sensor and CN21 on the Main PWB. If necessary, install a new bypass paper empty sensor, PL 8.20 Item 26. 5. If necessary, install new components: • Paper transport assembly, PL 8.20 Item 1. • Main PWB, PL 1.10 Item 1.

• Code: 07-530
• Description: Jam 0 From the Bypass Tray RAP The feed sensor failed to actuate within the correct time after paper was fed from the bypass tray.
• Remedy: 1. Switch off the machine, then switch on the machine. 2. Open the right cover assembly, PL 7.30 Item 1. Remove all jammed paper. 3. Check the paper path for damage or obstructions. 4. Check that the feed sensor actuator, PL 8.15 Item 5 moves freely and is not damaged. If necessary, install a new feed sensor actuator assembly, PL 8.15 Item 14. 5. Enter dC330 code 08-100. Check the feed sensor (Q08-100), PL 8.15 Item 8. 6. Check the wiring between the feed sensor and CN13 on the Main PWB. If necessary, install a new feed sensor, PL 8.15 Item 8. 7. Enter dC330 code 04-100 to run the main BLDC motor. 8. While the main BLDC motor runs, stack the code 08-800 to energize the bypass feed clutch (CL08-800). Check that the bypass tray feed roll, PL 8.20 Item 17 rotates. 9. Check the wiring between the bypass feed clutch, PL 8.20 Item 28 and CN21 on the Main PWB. Install new components as necessary, PL 8.20. 10. While the main BLDC motor runs, stack the code 08-850 to energize the registration clutch (CL08-850). Check that the registration roll, PL 4.15 Item 1 rotates. 11. Check the wiring between the registration clutch, PL 4.15 Item 4 and CN13 on the Main PWB. Install new components as necessary, PL 4.15. 12. Check that the following components are clean and rotate freely, install new components as necessary: • Bypass tray feed roll, PL 8.20 Item 17. • Registration roll, PL 4.15 Item 1. • Registration roll idler, PL 4.15 Item 7. 13. If necessary, install new components: • Paper transport assembly, PL 8.20 Item 1. • Main PWB, PL 1.10 Item 1.

• Code: 08-100
• Description: Jam 1 RAP 08-100 The lead edge of the document failed to actuate the exit sensor within the correct time after registration.
• Remedy: 1. Switch off the machine, then switch on the machine. 2. Open the right cover assembly, PL 7.30 Item 1. Remove all jammed paper. 3. Check the paper path for damage or obstructions. 4. Remove the fuser, PL 10.10 Item 4. Check that the exit sensor actuator, PL 10.25 Item 12 moves freely and is not damaged. If necessary, install a new exit sensor actuator, PL 10.25 Item 12. 5. Check the fuser stripper fingers, PL 10.25 Item 3. Install new components as necessary, PL 10.25. 6. Enter dC330 code 08-600. Check the exit sensor (Q08-600), PL 10.15 Item 2. 7. Check the wiring between the exit sensor and CN6 on the Main PWB. If necessary, install a new exit sensor, PL 10.15 Item 2. 8. Check that the registration sensor actuator, PL 8.15 Item 4 moves freely and is not damaged. If necessary, install a new registration sensor actuator assembly, PL 8.15 Item 13. 9. Enter dC330 code 08-500. Check the registration sensor (Q08-500), PL 8.15 Item 8. 10. Check the wiring between the registration sensor and CN13 on the Main PWB. If necessary, install a new registration sensor, PL 8.15 Item 8. 11. Enter dC330 code 10-400. Check that the fuser motor (MOT10-400), PL 10.20 Item 3, runs and drives the fuser rolls. 12. Check the wiring between the fuser motor and CN12 on the Main PWB. Install new components as necessary, PL 10.25. 13. Enter dC330 code 04-100 to run the main BLDC motor. 14. While the main BLDC motor runs, stack the code 08-850 to energize the registration clutch (CL08-850). Check that the registration roll, PL 4.15 Item 1 rotates. 15. Check the wiring between the registration clutch, PL 4.15 Item 4 and CN13 on the Main PWB. Install new components as necessary, PL 4.15. 16. Clean the registration roll, PL 4.15 Item 1 and the registration roll idler, PL 4.15 Item 7. Install new components as necessary. 17. Install new components as necessary: • Fuser, PL 10.10 Item 4. • Main PWB, PL 1.10 Item 1.

• Code: 08-200, 08-300, 08-400
• Description: Jam in Tray RAP 08-200 The machine has detected a paper jam in the tray 2 feed area. 08-300 The machine has detected a paper jam in the tray 3 feed area. 08-400 The machine has detected a paper jam in the tray 4 feed area.
• Remedy: 1. Pull out the tray. Remove all jammed paper. 2. Open the tray access door, PL 7.20 Item 18. Remove all jammed paper. 3. Check the paper path for damage or obstructions. 4. Check that the registration sensor actuator, PL 8.15 Item 4 moves freely and is not damaged. If necessary, install a new registration sensor actuator assembly, PL 8.15 Item 13. 5. Enter dC330 code 08-500. Check the registration sensor (Q08-500), PL 8.15 Item 8. 6. Check the wiring between the registration sensor and CN13 on the Main PWB. If necessary, install a new registration sensor, PL 8.15 Item 8. 7. Check that the tray feed sensor actuator, PL 7.25 Item 16 moves freely and is not damaged. 8. Enter dC330. Check the relevant tray feed sensor, PL 7.25 Item 14: • Tray 2. Code 08-200. • Tray 3. Code 08-300. • Tray 4. Code 08-400. 9. Check the wiring between the tray feed sensor and CN10 on the Tray PWB. If necessary, install a new feed sensor, PL 7.25 Item 14. 10. Enter dC330 code. Check that the relevant tray feed motor, PL 7.20 Item 9, runs and drives the tray transport roll, PL 7.25 Item 22: • Tray 2. Code 08-920. • Tray 3. Code 08-930. • Tray 4. Code 08-940. 11. Check the wiring between the tray feed motor and CN4 on the Tray PWB. 12. While the tray feed motor runs, stack the relevant code to energize the tray pickup clutch. Check that the tray feed roll, PL 7.25 Item 11 rotates: • Tray 2. Code 08-820. • Tray 3. Code 08-830. • Tray 4. Code 08-840. 13. Check the wiring between the tray pickup clutch and CN4 on the Tray PWB. 14. Check that the following components are clean and rotate freely: • Tray feed roll, PL 7.25 Item 11. • Tray nudger roll, PL 8.10 Item 12. • Tray retard roll, PL 8.10 Item 12. • Tray transport roll, PL 7.25 Item 22. • Tray transport roll idlers, part of the tray access door, PL 7.20 Item 18. 15. If necessary, install new components: • Tray feed roll, PL 7.25 Item 11. • Tray nudger roll, PL 8.10 Item 12. • Tray feed motor, PL 7.20 Item 9. • Tray PWB, PL 7.20 Item 6. • Tray assembly, PL 7.20 Item 1.

• Code: 08-500
• Description: Jam 2 RAP 08-500 The trail edge of the document failed to actuate the exit sensor within the correct time after registration.
• Remedy: 1. Open the right cover assembly, PL 7.30 Item 1. Remove all jammed paper. 2. Check the paper path for damage or obstructions. 3. Remove the fuser, PL 10.10 Item 4. Check that the exit sensor actuator, PL 10.25 Item 12 moves freely and is not damaged. If necessary, install a new exit sensor actuator, PL 10.25 Item 12. 4. Enter dC330 code 08-600. Check the exit sensor (Q08-600), PL 10.15 Item 2. 5. Check the wiring between the exit sensor and CN6 on the Main PWB. If necessary, install a new exit sensor, PL 10.15 Item 2. 6. Enter dC330 code 10-400. Check that the fuser motor (MOT10-400), PL 10.20 Item 3, runs and drives the fuser rolls and transport roll, PL 10.15 Item 22. 7. Check the wiring between the fuser motor and CN12 on the Main PWB. Install new components as necessary, PL 10.15 and PL 10.25. 8. Enter dC330 code 04-200. Check that the exit motor (MOT04-200), PL 10.20 Item 2, runs and drives the upper exit roll, PL 10.15 Item 23. 9. Check the wiring between the exit motor and CN12 on the Main PWB. Install new components as necessary, PL 10.15 and PL 10.20. 10. Check that the following components are clean and rotate freely: • Upper exit roll, PL 10.15 Item 23. • Lower exit roll, PL 10.15 Item 14. • Transport roll, PL 10.15 Item 22. • Transport roll idlers, PL 10.15 Item 19. 11. Install new components as necessary: • Fuser, PL 10.25 Item 1. • Exit assembly, PL 10.15 Item 1. • Main PWB, PL 1.10 Item 1.