Description: Tray1 F/O#1 SNR on JAM. Timeout between Tray1 Feed Clutch ON and Tray1 Feed Sensor ON.
Remedy: I/O Diagnostic Codes • [08-07] Tray1 Feed Sensor • [08-12] Tray1 Feed Clutch • Feed Roll or Retard Pad dirty, contaminated with paper dust, worn, or faulty • Tray1 Feed Sensor dirty and Sensor Actuator deformed or damaged • Paper damaged, not within specification, or not loaded correctly • Foreign matter, burrs, or paper in the paper path • Drive gear worn or damaged • Tray1 Feed Clutch faulty • Check that the following wires are connected securely with good electrical contact. If there is no problem, replace the Tray 1 Feed Sensor (PL 2.5) . – Wire between Tray 1 Feed Sensor J158-3 ( P/J158) and LVPS J501-6 ( P/J501) – Wire between Tray 1 Feed Sensor J158-2 and LVPS J501-7 – Wire between Tray 1 Feed Sensor J158-1 and LVPS J501-8 • Replace the Tray1 Feed Clutch (PL 2.2) and the AIOC PWB (PL 8.1) in that order.
Description: Tray1 Regi SNR on JAM. Timeout between Tray1 Feed Sensor ON and IOT Registration Sensor ON.
Remedy: I/O Diagnostic Codes • [08-07] Tray1 Feed Sensor • [08-05] IOT Registration Sensor • [08-10] IOT Registration Clutch Check Items: • Take Away Roll 1 dirty, contaminated with paper dust, worn, or faulty • Tray1 Feed Sensor dirty and Sensor Actuator deformed or damaged • Paper damaged, not within specification, or not loaded correctly • Foreign matter, burrs, or paper in the paper path • Drive gear worn or damaged • IOT Registration Clutch faulty • Check that the following wires are connected securely with good electrical contact. If there is no problem, replace the Tray 1 Feed Sensor (PL 2.5) . – Wire between Tray 1 Feed Sensor J158-3 ( P/J158) and LVPS J501-6 ( P/J501) – Wire between Tray 1 Feed Sensor J158-2 and LVPS J501-7 – Wire between Tray 1 Feed Sensor J158-1 and LVPS J501-8 • Check that the following wires are connected securely with good electrical contact. If there is no problem, replace the IOT Registration Sensor (PL 2.9). - Wire between IOT Registration Sensor J156-3 ( P/J156) and LVPS J503-1 ( P/J503) - Wire between IOT Registration Sensor J156-2 and LVPS J503-2 - Wire between IOT Registration Sensor J156-1 and LVPS J503-3 • Replace the IOT Registration Clutch (PL 2.9) and the AIOC PWB (PL 8.1) in that order.
Description: STM F/O#2 SNR on JAM. Timeout between STM Feed Motor ON and STM Feed Sensor ON.
Remedy: I/O Diagnostic Codes • [08-06] STM Feed Sensor • [08-11] STM Feed Clutch • [08-13] STM Feed Motor Check Items: • Tray2 Feed Roll or Tray2 Retard Roll dirty, contaminated with paper dust, worn, or faulty • STM Feed Sensor dirty and Sensor Actuator deformed or damaged • Paper damaged, not within specification, or not loaded correctly • Foreign matter, burrs, or paper in the paper path • Drive gear worn or damaged • STM Feed Clutch faulty • STM Feed Motor faulty • Check that the following wires are connected securely with good electrical contact. If there is no problem, replace the STM Feed Sensor (PL 11.5) . – - Wire between STM Feed Sensor J172-3 ( P/J172) and STM PWB J542-6 ( P/J542) – - Wire between STM Feed Sensor J172-2 and STM PWB J542-7 – - Wire between STM Feed Sensor J172-1 and STM PWB J542-8 • Replace the STM Feed Clutch (PL 11.6) , the STM Feed Motor (PL 11.6) , and the STM PWB (PL 11.5) in that order.
Description: Tray1 F/O#1 SNR on JAM from STM feed. Timeout between STM Feed Out Sensor ON and Tray 1 Feed Out Sensor ON.
Remedy: I/O Diagnostic Codes • [08-06] STM Feed Sensor • [08-07] Tray1 Feed Sensor • [08-11] STM Feed Clutch • [08-13] STM Feed Motor Check Items: • Take Away Roll 2 dirty, contaminated with paper dust, worn, or faulty • STM Feed Sensor dirty and Sensor Actuator deformed or damaged • Paper damaged, not within specification, or not loaded correctly • Foreign matter, burrs, or paper in the paper path • Drive gear worn or damaged • STM Feed Clutch faulty • STM Feed Motor faulty • Check that the following wires are connected securely with good electrical contact. If there is no problem, replace the STM Feed Sensor (PL 11.5) . – Wire between STM Feed Sensor J172-3 ( P/J172) and STM PWB J542-6 ( P/J542) – Wire between STM Feed Sensor J172-2 and STM PWB J542-7 – Wire between STM Feed Sensor J172-1 and STM PWB J542-8 • Check that the following wires are connected securely with good electrical contact. If there is no problem, replace the Tray 1 Feed Sensor (PL 2.5) . – Wire between Tray 1 Feed Sensor J158-3 ( P/J158) and STM PWB J501-6 ( P/J501) – Wire between Tray 1 Feed Sensor J158-2 and STM PWB J501-7 – Wire between Tray 1 Feed Sensor J158-1 and STM PWB J501-8 • Replace the STM Feed Clutch (PL 11.6) , the STM Feed Motor (PL 11.6) , and the STM PWB (PL 11.5) in that order.
Description: STM Regi SNR on JAM. • When feeding paper from the STM, timeout between Tray1 Feed Sensor ON and IOT Registration Sensor ON.
Remedy: I/O Diagnostic Codes • [08-05] IOT Registration Sensor • [08-10] IOT Registration Clutch Check Items: • Take Away Roll 1 dirty, contaminated with paper dust, worn, or faulty • IOT Registration Sensor dirty and Sensor Actuator deformed or damaged • Paper damaged, not within specification, or not loaded correctly • Foreign matter, burrs, or paper in the paper path • Drive gear worn or damaged • IOT Registration Clutch faulty • Check that the following wires are connected securely with good electrical contact. If there is no problem, replace the Tray 1 Feed Sensor (PL 2.5) . – Wire between Tray 1 Feed Sensor J158-3 ( P/J158) and LVPS J501-6 ( P/J502) – Wire between Tray 1 Feed Sensor J158-2 and LVPS J501-7 – Wire between Tray 1 Feed Sensor J158-1 and LVPS J501-8 • Check that the following wires are connected securely with good electrical contact. If there is no problem, replace the IOT Registration Sensor (PL 2.9). – Wire between Tray 1 Feed Sensor J156-3 ( P/J156) and LVPS J503-1 ( P/J503) – Wire between Tray 1 Feed Sensor J156-2 and LVPS J503-2 – Wire between Tray 1 Feed Sensor J156-1 and LVPS J503-3 • Replace the IOT Registration Clutch (PL 2.9) and the AIOC PWB (PL 8.1) in that order.
Description: No paper in the selected paper tray (Tray1). • No paper is detected in Tray1 when ATS function is disabled and Tray1 is selected during a copy job. • No paper is detected in Tray1 when Tray1 is selected during a print job (the paper size setting matches the one specified for the job).
Remedy: I/O Diagnostic Codes [07-07] Tray1 No Paper Sensor Check Items: • Press the [Stop] button on the Control Panel. • Check the tray to see if it is empty; if it is, add paper specified by the job. • Tray1 No Paper Sensor dirty and Sensor Actuator deformed or damaged • Check that the following wires are connected securely with good electrical contact. If there is no problem, replace the Tray 1 No Paper Sensor (PL 2.7) . – Wire between Tray1 No Paper Sensor J157-3 ( P/J157) and LVPS J501-3 ( P/J501) – Wire between Tray1 No Paper Sensor J157-2 and LVPS J501-4 – Wire between Tray1 No Paper Sensor J157-1 and LVPS J501-5 • Replace the AIOC PWB (PL 8.1) .
Description: Tray1 Paper Size Mismatch. • Paper that is different from the one in the Tray Settings is detected when feeding. • Or, paper size setting in Tray1 is different from the paper size specification of the job when Tray1 is selected during a print job.
Remedy: • Press the [Stop] button on the Control Panel. • Change the paper size of Tray 1 to the one specified by the job.
Description: No paper in the selected paper tray (Tray2). • No paper is detected in the STM when ATS function is disabled and STM is selected during a copy job. • No paper is detected in the STM when STM is selected during a print job (the paper size setting matches the one specified for the job).
Remedy: I/O Diagnostic Codes [07-08] STM No Paper Sensor Check Items: • Press the [Stop] button on the Control Panel. • Load the correct paper into the STM. • STM No Paper Sensor dirty and Sensor Actuator deformed or damaged. • Check that the following wires are connected securely with good electrical contact. If there is no problem, replace the STM No Paper Sensor (PL 11.7) . – Wire between STM No Paper Sensor J171-3 ( P/J171) and STM PWB J542-3 ( P/J542) – Wire between STM No Paper Sensor J171-2 and STM PWB J542-4 – Wire between STM No Paper Sensor J171-1 and STM PWB J542-5 • Replace the STM PWB (PL 11.5) and the AIOC PWB (PL 8.1) .
Nhận ưu đãi sớm nhất khi chương trình diễn ra
Đăng ký nhận bản tin
Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này.
Chính sách cookie
Những cookie này là cần thiết để trang web hoạt động đúng cách.
Những cookie này giúp chúng tôi hiểu cách khách truy cập tương tác với trang web.
Những cookie này được sử dụng để cung cấp quảng cáo cá nhân hóa.