• Code: 005-170
• Description: DADF Feed Failure BSD-Reference: CH 5.2. The control logic has detected the failure of paper to reach the Document Feed Sensor after the Feed Clutch has energized.
• Remedy: Check for obstructions in the Document Tray. Clean the Feed Roll. Confirm that a document is feeding into the document handler. The Feed Roller feeds paper into the document handler. Y↓N→The Document Drive Motor operates. Y↓N→Enter the Diagnostic Mode. Enter Component Control Code [05-01]. The Document Drive Motor operates. Y↓N→There is +24 VDC at connector CN2 pin 1 and pin 4 on the DADF PWB. Y↓N→Check the following in order: 1. Check the connectors CN1 and CN2 on the DADF PWB for proper connections 2. Check the connector J414 on the SLCC PWB (AIOC) for proper connection. 3. Check the harness from the DADF PWB to the SLCC PWB for an open circuit. If the harness and the connectors are good, replace the DADF PWB Replace the Document Drive Motor (PL 13.5) The Feed Roller rotates. Y↓N→Enter the Diagnostic Mode. Enter Component Control Code [05-62]. The Document Feed Clutch operates. Y↓N→Check the connector of the Document Feed Clutch (PL 13.9) If the connector is good, replace the Document Feed Clutch (PL 13.9). Replace the Document Feed Clutch (PL 13.9) Replace the Pick Up Roller and Feed Roller. The Feed Roller rotates. Y↓N→Enter the Diagnostic Mode. Enter Component Control Code [05-62]. The Document Feed Clutch operates. Y↓N→Check the connector of the Document Feed Clutch (PL 13.9) If the connector is good, replace the Document Feed Clutch (PL 13.9). Replace the Document Feed Clutch (PL 13.9) Replace the Pick Up Roller and Feed Roller. Replace the Document Feed Sensor (PL 13.9).

• Code: 005-171
• Description: DADF Regi / Exit Failure BSD-Reference: CH 5.8. Control logic has detected no paper at the Registration Sensor after turning on the Registration Clutch or detected no paper at the Exit/Invert Sensor after turning on the Registration Clutch.
• Remedy: Check for obstructions in the Document Tray. Clean the Feed Roll. Confirm that a document is feeding into the document handler. The Feed Roller feeds paper into the document handler. Y↓N→The Document Drive Motor operates. Y↓N→Enter the Diagnostic Mode. Enter Component Control Code [05-01]. The Document Drive Motor operates. Y↓N→There is +24 VDC at connector CN2 pin 1 and pin 4 on the DADF PWB. Y↓N→Check the following in order: 1. Check the connectors CN1 and CN2 on the DADF PWB for proper connections 2. Check the connector J414 on the SLCC PWB (AIOC) for proper connection. 3. Check the harness from the DADF PWB to the SLCC PWB for an open circuit. If the harness and the connectors are good, replace the DADF PWB Replace the Document Drive Motor (PL 13.5) The Feed Roller rotates. Y↓N→Enter the Diagnostic Mode. Enter Component Control Code [05-62]. The Document Feed Clutch operates. Y↓N→Check the connector of the Document Feed Clutch (PL 13.9) If the connector is good, replace the Document Feed Clutch (PL 13.9). Replace the Document Feed Clutch (PL 13.9) Replace the Pick Up Roller and Feed Roller. The Feed Roller rotates. Y↓N→Enter the Diagnostic Mode. Enter Component Control Code [05-62]. The Document Feed Clutch operates. Y↓N→Check the connector of the Document Feed Clutch (PL 13.9) If the connector is good, replace the Document Feed Clutch (PL 13.9). Replace the Document Feed Clutch (PL 13.9) Replace the Pick Up Roller and Feed Roller. Enter the Diagnostic Mode. Enter Component Control Code [05-206]. Actuate the Document Registration Sensor acutator. The display changes from High to Low. Y↓N→Replace the Document Registration Sensor. (PL 13.7) Enter the Diagnostic Mode. Enter Component Control Code [05-205]. Actuate the Exit/Invert Sensor actuator. The display changes from High to Low. Y↓N→Replace the Exit/Invert Sensor. (PL 13.7) Replace the DADF PWB , or replace the SLCC PWB (AIOC/Network)

• Code: 005-172
• Description: DADF Inverted Document Jam BSD-Reference: CH 5.8. When inverting documents, the control logic detected a failure of a document at the Feed Sensor after turning off the Feedout Forward or document failure at the Exit/Invert Sensor after turning on the Document Registration Sensor.
• Remedy: Check for obstructions in the Document Tray. Clean the Feed Roll. Confirm that a document is feeding into the document handler. The Feed Roller feeds paper into the document handler. Y↓N→The Document Drive Motor operates. Y↓N→Enter the Diagnostic Mode. Enter Component Control Code [05-01]. The Document Drive Motor operates. Y↓N→There is +24 VDC at connector CN2 pin 1 and pin 4 on the DADF PWB. Y↓N→Check the following in order: 1. Check the connectors CN1 and CN2 on the DADF PWB for proper connections 2. Check the connector J414 on the SLCC PWB (AIOC) for proper connection. 3. Check the harness from the DADF PWB to the SLCC PWB for an open circuit. If the harness and the connectors are good, replace the DADF PWB Replace the Document Drive Motor (PL 13.5) The Feed Roller rotates. Y↓N→Enter the Diagnostic Mode. Enter Component Control Code [05-62]. The Document Feed Clutch operates. Y↓N→Check the connector of the Document Feed Clutch (PL 13.9) If the connector is good, replace the Document Feed Clutch (PL 13.9). Replace the Document Feed Clutch (PL 13.9) Replace the Pick Up Roller and Feed Roller. The Feed Roller rotates. Y↓N→Enter the Diagnostic Mode. Enter Component Control Code [05-62]. The Document Feed Clutch operates. Y↓N→Check the connector of the Document Feed Clutch (PL 13.9) If the connector is good, replace the Document Feed Clutch (PL 13.9). Replace the Document Feed Clutch (PL 13.9) Replace the Pick Up Roller and Feed Roller. Enter the Diagnostic Mode. Enter Component Control Code [05-204]. Actuate the Document Feed Sensor acutator. The display changes from High to Low. Y↓N→Replace the Document Feed Sensor. (PL 13.9) Enter the Diagnostic Mode. Enter Component Control Code [05-205]. Actuate the Exit/Invert Sensor actuator. The display changes from High to Low. Y↓N→Replace the Exit/Invert Sensor. (PL 13.7) Replace the DADF PWB , or replace the SLCC PWB (AIOC/Network)

• Code: 005-198
• Description: Short Scan Jam BSD-Reference: CH 6.2. The control logic has found that the length of slow scan is less than 80mm.
• Remedy: Choose a document size equal to or larger than A4 paper or 208mm SEF or larger, in the Document Tray. The problem is solved. Y↓N→Replace the Document Registration Sensor. (PL 13.7) Inform the customer of the minimum size limitation of documents used in the DADF Document Tray.

• Code: 005-199
• Description: 005-199 Long Scan Jam BSD-Reference: CH 6.2. The control logic has detected that the length of slow scan is 450mm or more.
• Remedy: Choose a document size equal to or less than A3 paper or 294mm SEF or less in the Document Tray. The problem is solved. Y↓N→Replace the Document Registration Sensor. (PL 13.7) Inform the customer of the maximum size limitation of documents used in the DADF Document Tray.

• Code: 005-305
• Description: Feeder Top Cover Open BSD-Reference: CH 5.6. The control logic has detected that the Feeder Top Cover is open.
• Remedy: Close the Feeder Top Cover. The problem continues. Y↓N→Adjust or repair the Feeder Top Cover latch. Replave the Feeder Top Cover Switch. (PL 13.9)

• Code: 005-920
• Description: Static Jam BSD-Reference: CH 5.6. At power on, the control logic detected either the Platen Interlock is close when the Feeder Cover is open or the Feeder Cover Interlock is close when the Platen Interlock is open.
• Remedy: If this occurs frequently, confirm if there is any interferance with the Feed Sensor (PL 13.9), the Document Registration Sensor (PL 13.7) or the Exit/Invert Sensor (PL 13.7). Check the sensor connectors for prober connection. Replace one sensor at a time until the problem is solved.

• Code: 062-300
• Description: Platen Interlock Open BSD-Reference: CH 5.6. Detected the opened Platen Interlock.
• Remedy: Ensure that the DADF can be closed normally. The DADF can be closed normally. Y↓N→Remove obstructions or repair the DADF Counter Balances. Check that the Platen Interlock is functioning properly. The Platen Interlock is functioning properly. Y↓N→Replace the Platen Interlock Sensor. Replace the SLCC PWB (AIOC/Network PWB). (PL 8.1)