Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Xerox WorkCentre 5024 — Trang 14/18

Code: 077-211

Description: 2TM Type Error An unsupported 2TM was detected to be connected. NOTE: If this is already detected, it will be displayed on the UI Panel when a Job is being performed.
Remedy: 1. Turn the power OFF and ON. 2. Turn OFF the power and check the following: • The DIP Switch setting on the 2TM PWB • The connection between the 2TM PWB J541 and the STM PWB J413C for open circuit, short circuit, and poor contact • The connection between the STM PWB J541C and the ESS/MCU PWB J413 for open circuit, short circuit, and poor contact If no problems are found, replace the following parts in sequence: • 2TM PWB (PL 11.6) • STM PWB (PL 10.6) • ESS/MCU PWB (PL 18.3)

Code: 077-212

Description: Tray Module Reset Fail The Tray Module was detected to be reset.
Remedy: 1. Turn the power OFF and ON. 2. Check voltages of the following pins: • STM PWB J541C-5 (+5VDC) • STM PWB J541C-8 (+24VDC) 3. Turn OFF the power and check the connection between the ESS/MCU PWB J413 and the STM PWB J541C for open circuit, short circuit, and poor contact. 4. If no problem is found, replace the following parts in sequence: • STM PWB (PL 10.6) • ESS/MCU PWB (PL 18.3)

Code: 077-300

Description: Front Cover Open The Front Cover Switch was detected to be open.
Remedy: 1. Check the Front Cover Switch for operation failure. • Front Cover Switch (Input Check [071-301]) (PL 19.1) 2. Check the Front Cover Switch for damage and mismatch. 3. If no problem is found, replace the following parts: • ESS/MCU PWB (PL 18.3)

Code: 077-301

Description: Left Hand Cover Open The Left Hand Cover Switch was detected to be open.
Remedy: 1. Check the Left Hand Cover Switch for operation failure. • Left Hand Cover Interlock Switch (Input Check [071-300]) (PL 14.1) 2. Check the Left Hand Cover Switch for damage and mismatch. 3. If no problem is found, replace the following parts: • ESS/MCU PWB (PL 18.3)

Code: 077-305

Description: 2TM Cover Open The 2TM Left Cover Switch was detected to be open.
Remedy: 1. Check the 2TM Left Cover Switch for operation failure. • 2TM Left Cover Switch (Input Check [072-301]) (PL 11.4) 2. Check the 2TM Left Cover Switch for damage and mismatch. 3. If no problem is found, replace the following parts: • 2TM PWB (PL 11.6)

Code: 077-309

Description: STM Cover Open The STM Left Cover Switch was detected to be open.
Remedy: 1. Check the STM Left Cover Switch for operation failure. • STM Left Cover Switch (Input Check[072-300]) (PL 10.4) 2. Check the STM Left Cover Switch for damage and mismatch. 3. If no problem is found, replace the following parts: • STM PWB (PL 10.6)

Code: 077-900, 077-901, 077-904

Description: Regi Sensor/Fusing Unit Exit Sensor/ Feed Out Sensor 2 Static Jam BSD-ON: Paper was detected by the applicable sensor at Power ON, M/C Stop, or Interlock Close.
Remedy: 1. Check the applicable sensor for remaining paper, the Actuator for return failure, contamination on sensor, and etc. 2. Check the applicable sensor for operation failure. • Regi Sensor (Input Check [071-105]) (PL 15.1) • Fusing Unit Exit Sensor (Input Check [071-106]) (PL 7.1) • Feed Out Sensor 2 (Input Check [072-106]) (PL 10.5) 3. If no problem is found, replace the following parts: • ESS/MCU PWB (Regi Sensor, Fusing Unit Exit Sensor) (PL 18.3) • STM PWB (Feed Out Sensor 2) (PL 10.6)

Code: 077-905

Description: Feed Out Sensor 3 Static Jam Feed Out Sensor 3 On was detected during Standby.
Remedy: Check the following: • The Feed Out Sensor 3 for remaining paper, Actuator return failure, foreign substances, contamination on sensor, and etc. • Feed Out Sensor 3: Input Check [072-109] (PL 11.5) If no problems are found, replace the 2TM PWB (PL 11.6).
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie