Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Xerox WorkCentre 5024 — Trang 11/18

Code: 062-396

Description: CCD Cable Connection Fail A CCD Flat Cable connection error was detected.
Remedy: 1. Turn the power OFF and ON. 2. Turn OFF the power and check the Flat Cable between the CCD PWB J700 and the ESS/MCU PWB J420 for open circuits, short circuits, and poor contacts (especially, check whether the Flat Cable was inserted in a skewed manner). 3. If no problem is found, replace the following parts in sequence: • CCD Flexible Flat Cable (PL 1.9) • ESS/MCU PWB (PL 18.3)

Code: 071-105

Description: Regi Sensor On Jam (Tray 1) During paper feed from Tray 1, the Regi Sensor did not turn ON within the specified time after the Tray 1 Feed Clutch On.
Remedy: Check the following: • The Regi Sensor (Input Check [071-105]) for operation failure. (PL 15.1) • The Main Drive Motor (Output Check [042-001]) for operation failure. (PL 3.1) • The Tray 1 Feed Clutch (Output Check [072-001]) for operation failure. (PL 9.1) • The Feed Roll for contamination, wear, and transportation failure due to deterioration. • The Drive Gear for wear and damage. • A paper transportation failure due to foreign substances on the paper path. • Usage of out of spec paper. If no problems are found, replace the ESS/MCU PWB (PL 18.3)

Code: 072-102

Description: Feed Out Sensor 2 On Jam During paper feed from Tray 2, the Feed Out Sensor 2 did not turn ON within the specified time after the Tray 2 Feed Motor On.
Remedy: Check the following: • The Feed Out Sensor 2 (Input Check [072-106] for operation failure. (PL 10.5) • The STM Take Away Motor (Output Check [072-007] for operation failure. (PL 10.6) • The STM Take Away Roll Clutch (Output Check [072-005] for operation failure. (PL 10.6) • The Tray 2 Feed/Lift Up Motor (Output Check [072-002] (Feed)) for operation failure. (PL 10.3) • The T/A Roll 2, Feed Roll, Nudger Roll, and Pinch Roll for transportation failure due to contamination, wear, and deterioration. • The LH Cover for improper latching. • The Drive Gear for wear and damage. • A paper transportation failure due to foreign substances on the paper path. • Usage of out of spec paper. If no problem is found, replace the STM PWB. (PL 10.6)

Code: 072-105

Description: Regi Sensor On Jam (Tray 2) During paper feed from Tray 2, the Regi Sensor did not turn ON within the specified time after the Feed Out Sensor 2 On.
Remedy: Check the following: • The Regi Sensor (Input Check [071-105]) for operation failure. (PL 15.1) • The STM Take Away Motor (Output Check [072-007] for operation failure. (PL 10.6) • The STM Take Away Roll Clutch (Output Check [072-005] for operation failure. (PL 10.6) • The T/A Roll 2, Feed Roll, and Pinch Roll for transportation failure due to contamination, wear, and deterioration. • The Drive Gear for wear and damage. • A paper transportation failure due to foreign substances on the paper path. • Usage of out of spec paper. If no problem is found, replace the following parts in sequence: • ESS/MCU PWB (PL 18.3) • STM PWB (PL 10.6)

Code: 072-210

Description: Tray 2 Lift Up Fail Any of the following was detected: • A Tray 2 Lifter error. • A Tray 2 Paper Size detector component malfunction
Remedy: Check the following: • The Tray 2 Nudger Level Sensor (Input Check [072-105] for operation failure. (PL 10.3) • The Tray 2 Feed/Lift Motor (Output Check [072-009] (Lift Up) for operation failure. (PL 10.3) • The drive system between the Bottom Plate and the Tray 2 Feed/Lift Motor for operation failure. • The Tray for Paper misload • The Tray for existence of objects other than Paper. If no problem is found, replace the STM PWB. (PL 10.6)

Code: 072-212

Description: Tray 2 Size Sensor Broken Abnormal output AD value from Tray 2 Paper Size Switch was detected.
Remedy: Check the following: • Broken link and damage at the bottom of the Tray • The Actuator at the rear of the Tray for operation failure • The Tray 2 Paper Size Switch (Analog Monitor [072-051], Output Check [072-107] for operation failure. (PL 10.1) • The Tray for Paper misload • The Tray for existence of objects other than Paper. If no problem is found, replace the STM PWB. (PL 10.6)

Code: 072-215

Description: MCU-STM Communication Fail Communication failure between the ESS/MCU PWB and the STM PWB was detected.
Remedy: 1. Turn the power OFF and ON. 2. Turn OFF the power and check the connection between the ESS/MCU PWB J413 and the STM PWB J541C for open circuit, short circuit, and poor contact. 3. If no problem is found, replace the following parts in sequence: • STM PWB (PL 10.6) • ESS/MCU PWB (PL 18.3)

Code: 072-461

Description: STM NVM Out-Of-Order The NVM of the STM is malfunctioning. NOTE: If this is already detected, it will be displayed on the UI Panel when a Job is being performed.
Remedy: 1. Turn the power OFF and ON. 2. If the problem persists, replace the STM PWB (PL 10.6).
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie