Description: STM NVM R/W Error The NVM of the STM cannot be read or written. NOTE: If this is already detected, it will be displayed on the UI Panel when a Job is being performed.
Remedy: 1. Turn the power OFF and ON. 2. If the problem persists, replace the STM PWB (PL 10.6).
Description: Feed Out Sensor 3 On Jam (Tray 3) The Feed Out Sensor 3 did not turn ON within the specified time after the Paper had been fed from Tray 3.
Remedy: Check the following: • A paper transportation failure due to a foreign substance/burr on the paper path. • Usage of out of spec paper. • The Drive Gear for wear and damage. • The Tray 3 Feed Roll, Retard Roll, and Nudger Roll for contamination, wear, and transportation failure due to deterioration. • The Tray 3 Takeaway Roll and Pinch Roll for contamination, wear, and transportation failure due to deterioration. • Feed Out Sensor 3: Input Check [072-109] (PL 11.5) • Tray 3 Feed/Lift Up Motor: Output Check [072-003] (Feed) (PL 11.3) • 2TM Takeaway Motor: Output Check [072-008] (PL 11.6) • 2TM Takeaway Roll Clutch: Output Check [072-006] (PL 11.6) If no problems are found, replace the following parts in sequence: • 2TM PWB (PL 11.6) • ESS/MCU PWB (PL 18.3)
Description: Feed Out Sensor 2 On Jam (Tray 3) The Feed Out Sensor 2 did not turn ON within the specified time after the Feed Out Sensor 3 is On during paper feed from Tray 3.
Remedy: Check the following: • A paper transportation failure due to a foreign substance/burr on the paper path. • Usage of out of spec paper. • The Drive Gear for wear and damage. • The Tray 2 Takeaway Roll and Pinch Roll for contamination, wear, and transportation failure due to deterioration. • The Tray 3 Takeaway Roll and Pinch Roll for contamination, wear, and transportation failure due to deterioration. • Feed Out Sensor 2: Input Check [072-106] (PL 10.5) • Feed Out Sensor 3: Input Check [072-109] (PL 11.5) • STM Takeaway Motor: Output Check [072-007] (PL 10.6) • STM Takeaway Roll Clutch: Output Check [072-005] (PL 10.6) • 2TM Takeaway Motor: Output Check [072-008] (PL 11.6) • 2TM Takeaway Roll Clutch: Output Check [072-006] (PL 11.6) If no problems are found, replace the following parts in sequence: • STM PWB (PL 10.6) • 2TM PWB (PL 11.6) • ESS/MCU PWB (PL 18.3)
Description: Regi Sensor On Jam (Tray 3) The Regi Sensor did not turn ON within the specified time after the Feed Out Sensor 2 is On during paper feed from Tray 3.
Remedy: Check the following: • A paper transportation failure due to a foreign substance/burr on the paper path. • Usage of out of spec paper. • The Drive Gear for wear and damage. • The Tray 2 Takeaway Roll and Pinch Roll for contamination, wear, and transportation failure due to deterioration. • Regi Sensor: Input Check [071-105] (PL 15.1) • Feed Out Sensor 2: Input Check [072-106] (PL 10.5) • STM Takeaway Motor: Output Check [072-007] (PL 10.6) • STM Takeaway Roll Clutch: Output Check [072-005] (PL 10.6) If no problems are found, replace the following parts in sequence: • STM PWB (PL 10.6) • ESS/MCU PWB (PL 18.3)
Description: Tray 3 Lift Up Fail One of the following errors was detected. • The Tray 3 Lifter error was detected. • The Tray 3 Paper Size detector component malfunction was detected. NOTE: If this is already detected, it will be displayed on the UI Panel when a Job is being performed.
Remedy: Check the following: • The Tray 3 paper supply mechanism for damage and foreign substances. • Usage of out of spec paper. • Tray 3 Nudger Level Sensor: Input Check [072-108] (PL 11.3) • Tray 3 Feed/Lift Up Motor: Output Check [072-010] (Lift Up) (PL 11.3) • Tray 3 Paper Size Switch: Analog Monitor [072-052]/Input Check [072-110] (PL 11.1) If no problems are found, replace the following parts in sequence: • 2TM PWB (PL 11.6) • ESS/MCU PWB (PL 18.3)
Description: Feed Out Sensor 4 On Jam (Tray 4) The Feed Out Sensor 4 did not turn ON within the specified time after the Paper had been fed from Tray 4.
Remedy: Check the following: • A paper transportation failure due to a foreign substance/burr on the paper path. • Usage of out of spec paper. • The Drive Gear for wear and damage. • The Tray 4 Feed Roll, Retard Roll, and Nudger Roll for contamination, wear, and transportation failure due to deterioration. • The Tray 4 Takeaway Roll and Pinch Roll for contamination, wear, and transportation failure due to deterioration. • Feed Out Sensor 4: Input Check [072-112] (PL 11.5) • Tray 4 Feed/Lift Up Motor: Output Check [072-011] (Feed) (PL 11.3) • 2TM Takeaway Motor: Output Check [072-008] (PL 11.6) • 2TM Takeaway Roll Clutch: Output Check [072-006] (PL 11.6) If no problems are found, replace the following parts in sequence: • 2TM PWB (PL 11.6) • ESS/MCU PWB (PL 18.3)
Description: Feed Out Sensor 3 On Jam (Tray 4) The Feed Out Sensor 3 did not turn ON within the specified time after the Feed Out Sensor 4 is On during paper feed from Tray 4.
Remedy: Check the following: • A paper transportation failure due to a foreign substance/burr on the paper path. • Usage of out of spec paper. • The Drive Gear for wear and damage. • The Tray 4 Takeaway Roll and Pinch Roll for contamination, wear, and transportation failure due to deterioration. • The Tray 3 Takeaway Roll and Pinch Roll for contamination, wear, and transportation failure due to deterioration. • Feed Out Sensor 4: Input Check [072-112] (PL 11.5) • Feed Out Sensor 3: Input Check [072-109] (PL 11.5) • 2TM Takeaway Motor: Output Check [072-008] (PL 11.6) • 2TM Takeaway Roll Clutch: Output Check [072-006] (PL 11.6) If no problems are found, replace the following parts in sequence: • 2TM PWB (PL 11.6) • ESS/MCU PWB (PL 18.3)
Description: Feed Out Sensor 2 On Jam (Tray 4) The Feed Out Sensor 2 did not turn ON within the specified time after the Feed Out Sensor 3 is On during paper feed from Tray 4.
Remedy: Check the following: • A paper transportation failure due to a foreign substance/burr on the paper path. • Usage of out of spec paper. • The Drive Gear for wear and damage. • The Tray 2 Takeaway Roll and Pinch Roll for contamination, wear, and transportation failure due to deterioration. • The Tray 3 Takeaway Roll and Pinch Roll for contamination, wear, and transportation failure due to deterioration. • Feed Out Sensor 2: Input Check [072-106] (PL 10.5) • Feed Out Sensor 3: Input Check [072-109] (PL 11.5) • STM Takeaway Motor: Output Check [072-007] (PL 10.6) • STM Takeaway Roll Clutch: Output Check [072-005] (PL 10.6) • 2TM Takeaway Motor: Output Check [072-008] (PL 11.6) • 2TM Takeaway Roll Clutch: Output Check [072-006] (PL 11.6) If no problems are found, replace the following parts in sequence: • STM PWB (PL 10.6) • 2TM PWB (PL 11.6) • ESS/MCU PWB (PL 18.3)
Nhận ưu đãi sớm nhất khi chương trình diễn ra
Đăng ký nhận bản tin
Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này.
Chính sách cookie
Những cookie này là cần thiết để trang web hoạt động đúng cách.
Những cookie này giúp chúng tôi hiểu cách khách truy cập tương tác với trang web.
Những cookie này được sử dụng để cung cấp quảng cáo cá nhân hóa.