Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Xerox WorkCentre 5024 — Trang 15/18

Code: 077-906

Description: Feed Out Sensor 4 Static Jam Feed Out Sensor 4 On was detected during Standby.
Remedy: Check the following: • The Feed Out Sensor 4 for remaining paper, Actuator return failure, foreign substances, contamination on sensor, and etc. • Feed Out Sensor 4: Input Check [072-112] (PL 11.5) If no problems are found, replace the 2TM PWB (PL 11.6).

Code: 091-401, 091-402

Description: Drum Cartridge Quality Life Over/ Drum Cartridge Life Over [Drum Cartridge Quality Life Over] The image quality guarantee period for the Drum Cartridge has ended. (When Drum Hard Stop-less is enabled) [Drum Cartridge Life Over] When in Life Extension Mode, the Drum Cartridge was detected to be near the end of its life span
Remedy: Replace the Drum Cartridge. (PL 8.1) NOTE: After replacing the Drum Cartridge, clear the HFSI [950-807] (Drum Cycle Counter) to '0'.

Code: 091-406, 091-424

Description: Drum Cartridge Normal Life Over/ Drum Cartridge Abnormal Life Over [Drum Cartridge Normal Life Over] The operation guarantee period for the Drum Cartridge has ended. (When Drum Hard Stopless is enabled) [Drum Cartridge Abnormal Life Over] The Drum Cartridge is out of warranty and this could result in a malfunction of the machine. (When Drum Hard Stop-less is enabled)
Remedy: Replace the Drum Cartridge. (PL 8.1) NOTE: After replacing the Drum Cartridge, clear the HFSI [950-807] (Drum Cycle Counter) to '0'.

Code: 091-430

Description: Drum Cartridge Life End The Drum Cartridge must be replaced
Remedy: Replace the Drum Cartridge. (PL 8.1) NOTE: After replacing the Drum Cartridge, clear the HFSI [950-807] (Drum Cycle Counter) to '0'.

Code: 091-440

Description: Drum Cartridge Pre Near End Preparation for replacing the Drum Cartridge is required.
Remedy: The Drum Cartridge needs to be replaced soon. Prepare a new Drum Cartridge. Replace the Drum Cartridge as required. (PL 8.1) NOTE: After replacing the Drum Cartridge, clear the HFSI [950-807] (Drum Cycle Counter) to '0'.

Code: 091-441

Description: Drum Cartridge Near End The Drum Cartridge needs to be replaced soon.
Remedy: The Drum Cartridge needs to be replaced soon. Replace the Drum Cartridge as required. (PL 8.1) NOTE: After replacing the Drum Cartridge, clear the HFSI [950-807] (Drum Cycle Counter) to '0'.

Code: 092-660, 092-668

Description: ATC Amplitude Fail/ ATC Average Fail [ATC Amplitude Fail] The output amplitude of the ATC Sensor in the ATC (Automatic Toner Control) measurement is small. [ATC Average Fail] The average output value is not within the specified range in the ATC (Automatic Toner Control) measurement.
Remedy: 1. Install a Toner Cartridge that contains Toner. Copy a Test Chart (499T247), etc. and check whether the density has recovered. 2. Check the Toner Dispense Motor (Output Check [092-001]) for operation failure. (PL 8.2) 3. Check the Toner transport path for Toner blockage. 4. Check the connection between the ATC Sensor P615 and the ESS/MCU PWB J409 for open circuit, short circuit, and poor contact. 5. If no problem is found, replace the following parts in sequence: • ATC Sensor (PL 8.6) • Developer Unit (PL 8.4) • Drum Cartridge (PL 8.1) NOTE: After replacing the Drum Cartridge, clear the HFSI [950-807] (Drum Cycle Counter) to '0'. • ESS/MCU PWB (PL 18.3)

Code: 092-661

Description: Temperature Sensor Fail The output value of the Temperature Sensor is not within the specification range.
Remedy: 1. Turn the power OFF and ON. 2. Check the connection between the HVPS J500-1 and the ESS/MCU PWB J402-14 for open circuit, short circuit, and poor contact. 3. If no problem is found, replace the following parts in sequence: • HVPS (PL 18.3) • ESS/MCU PWB (PL 18.3)
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie