• Code: 012-126
• Description: H-Transport Entrance. SNR OFF JAM B RAP After the H-Transport Entrance Sensor turned On, the H-Transport Entrance Sensor did not turn Off within the specified time.
• Remedy: Check the Transport Roll for wear and paper powder. The Transport Roll is ok. Y↓N→Replace the Transport Roll. Check for foreign substances, distortion and paper powder in the paper transport path. No foreign substances, distortion or paper powder are found in the paper transport path. Y↓N→Clear away the foreign substances and paper powder. Correct the distortion. Execute Component Control[012-190 H-Transport Entrance Sensor]. Actuate the H-Transport Entrance Sensor (PL 23.4) with paper. The display changes. Y↓N→Check the connections of J8861 and J8987. J8861 and J8987 are connected correctly. Y↓N→Connect J8861 and J8987. Check the wire between J8861 and J8987 for an open circuit or a short circuit. The wire between J8861 and J8897 is conducting without an open circuit or a short circuit. Y↓N→Repair the open circuit or short circuit. Measure the voltage between the Finisher PWB P8987-4 (+) and GND (-). The voltage is approx. +5VDC. Y↓N→Replace the Finisher PWB (PL 23.16). Measure the voltage between the Finisher PWB P8987-6 (+) and GND (-). Actuate the H-Transport Entrance Sensor with paper. The voltage changes. Y↓N→Replace the H-Transport Entrance Sensor (PL 23.4). Replace the Finisher PWB (PL 23.16). Power OFF. Open the H-Transport Top Cover. Cheat the H-Transport Interlock Sensor. Power ON. The H-Transport Belt rotates. Y↓N→Check the connections of P/J8862 and J8987. P/J8862 and J8987 are connected correctly. Y↓N→Connect P/J8862 and J8987. Check the wire between J8862 and J8987 for an open circuit or a short circuit. The wire between J8862 and J8987 is conducting without an open circuit or a short circuit. Y↓N→Repair the open circuit or short circuit. Measure the resistance of the H-Transport Motor between each point of J8862-1/2/5/6. The resistance is approx. 20Ohm. Y↓N→Replace the H-Transport Motor (PL 23.4). Measure the voltage between the Finisher PWB J8987-21/22/23/24 (+) and GND (-),. The voltage is approx. +24VDC. Y↓N→Replace the Finisher PWB (PL 23.16). Replace the H-Transport Motor (PL 23.4). If the problem persists, replace the Finisher PWB (PL 23.16). Replace the Finisher PWB (PL 23.16).

• Code: 012-131
• Description: H-Transport Entrance Sensor On JAM B RAP After the Engine Fuser Exit Sensor turned On, the H-Transport Entrance Sensor did not turn On within the specified time.
• Remedy: Check the Transport Roll for wear and paper powder. The Transport Roll is ok. Y↓N→Replace the Transport Roll. Check for foreign substances, distortion and paper powder in the paper transport path. No distortion, foreign substances, or paper powder are found in the paper transport path. Y↓N→Clear away the foreign substances and paper powder. Correct the distortion. Execute Component Control[012-190 H-Transport Entrance Sensor]. Actuate the H-Transport Entrance Sensor (PL 23.4) with paper. The display changes. Y↓N→Check the connections of J8861 and J8987. J8861 and J8987 are connected correctly. Y↓N→Connect J8861 and J8987. Check the wire between J8861 and J8987 for an open circuit or a short circuit. The wire between J8861 and J8897 is conducting without an open circuit or a short circuit. Y↓N→Repair the open circuit or short circuit. Measure the voltage between the Finisher PWB P8987-4 (+) and GND (-). The voltage is approx. +5VDC. Y↓N→Replace the Finisher PWB (PL 23.16). Measure the voltage between the Finisher PWB P8987-6 (+) and GND (-). Actuate the H-Transport Entrance Sensor with paper. The voltage changes. Y↓N→Replace the H-Transport Entrance Sensor (PL 23.4). Replace the Finisher PWB (PL 23.16). Power OFF. Open the H-Transport Top Cover. Cheat the H-Transport Interlock Sensor. Power ON. The H-Transport Belt rotates. Y↓N→Check the connections of P/J8862 and J8987. P/J8862 and J8987 are connected correctly. Y↓N→Connect P/J8862 and J8987. Check the wire between J8862 and J8987 for an open circuit or a short circuit. The wire between J8862 and J8987 is conducting without an open circuit or a short circuit. Y↓N→Repair the open circuit or short circuit. Measure the resistance of the H-Transport Motor between each point of J8862-1/2/5/6. The resistance is approx. 20Ohm. Y↓N→Replace the H-Transport Motor (PL 23.4). Measure the voltage between the Finisher PWB J8987-21/22/23/24 (+) and GND (-),. The voltage is approx. +24VDC. Y↓N→Replace the Finisher PWB (PL 23.16). Replace the H-Transport Motor (PL 23.4). If the problem persists, replace the Finisher PWB (PL 23.16). Replace the Finisher PWB (PL 23.16).

• Code: 012-132
• Description: (A-Finisher) Ent Sensor ON Jam Finisher Entrance Sensor does not turn On within a specified time after receiving the Sheet Exit command (the sheet to be ejected has turned ON the IOT Exit Sensor 1).
• Remedy: Check the specifications of paper. Paper is in spec. Y↓N→Replace the paper with new paper that is in spec. Check the condition of the paper. The paper is in normal condition without any problem that causes the paper to be bent or caught. Y↓N→Resolve any problem that causes the paper to be bent or caught. Check the transport path for a foreign object, deformed part, and paper dust. The transport path is in normal condition. Y↓N→Repair the deformed part(s) and remove the foreign object(s) and paper dust. Check that the Finisher is installed properly. The Finisher is properly installed and properly connected to the IOT. Y↓N→Reinstall the Finisher properly. Enter Component Control [012-140]. Actuate the Finisher Entrance Sensor. The display changes. Y↓N→Check the connections of P/J8709 and P/J8729. P/J8709 and P/J8729 are securely connected. Y↓N→Connect P/J8709 and P/J8729 securely. Check for an open or short circuit between J8709 and J8729. The wires between J8709 and J8729 are OK. Y↓N→Repair the open or short circuit. Measure the voltage between Finisher PWB J8709-6 (+) and GND (-). The voltage is approx. +5VDC. Y↓N→Go to Wirenet A-Finisher +5VDC and check the +5VDC circuit. Measure the voltage between Finisher PWB J8709-5 (+) and GND (-). Actuate the Finisher Entrance Sensor. The voltage changes. Y↓N→Replace the Finisher Entrance Sensor (PL 22.5). Check the wires and connectors for an intermittent open or short circuit. If the problem continues, replace the Finisher PWB (PL 22.7). Check the wires and connectors for an intermittent open or short circuit. If the problem continues, replace the Finisher PWB (PL 22.7).

• Code: 012-132
• Description: H-Transport Entrance Sensor On JAM RAP After the Engine Fuser Exit Sensor turned On, the H-Transport Entrance Sensor did not turn On within the specified time.
• Remedy: Check the Transport Roll for wear and paper powder. The Transport Roll is ok. Y↓N→Replace the Transport Roll. Check for foreign substances, distortion and paper powder in the paper transport path. No distortion, foreign substances, or paper powder are found in the paper transport path. Y↓N→Clear away the foreign substances and paper powder. Correct the distortion. Execute Component Control[012-190 H-Transport Entrance Sensor]. Actuate the H-Transport Entrance Sensor (PL 23.4) with paper. The display changes. Y↓N→Check the connections of J8861 and J8987. J8861 and J8987 are connected correctly. Y↓N→Connect J8861 and J8987. Check the wire between J8861 and J8987 for an open circuit or a short circuit. The wire between J8861 and J8897 is conducting without an open circuit or a short circuit. Y↓N→Repair the open circuit or short circuit. Measure the voltage between the Finisher PWB P8987-4 (+) and GND (-). The voltage is approx. +5VDC. Y↓N→Replace the Finisher PWB (PL 23.16). Measure the voltage between the Finisher PWB P8987-6 (+) and GND (-). Actuate the H-Transport Entrance Sensor with paper. The voltage changes. Y↓N→Replace the H-Transport Entrance Sensor (PL 23.4). Replace the Finisher PWB (PL 23.16). Power OFF. Open the H-Transport Top Cover. Cheat the H-Transport Interlock Sensor. Power ON. The H-Transport Belt rotates. Y↓N→Check the connections of P/J8862 and J8987. P/J8862 and J8987 are connected correctly. Y↓N→Connect P/J8862 and J8987. Check the wire between J8862 and J8987 for an open circuit or a short circuit. The wire between J8862 and J8987 is conducting without an open circuit or a short circuit. Y↓N→Repair the open circuit or short circuit. Measure the resistance of the H-Transport Motor between each point of J8862-1/2/5/6. The resistance is approx. 20Ohm. Y↓N→Replace the H-Transport Motor (PL 23.4). Measure the voltage between the Finisher PWB J8987-21/22/23/24 (+) and GND (-),. The voltage is approx. +24VDC. Y↓N→Replace the Finisher PWB (PL 23.16). Replace the H-Transport Motor (PL 23.4). If the problem persists, replace the Finisher PWB (PL 23.16). Replace the Finisher PWB (PL 23.16).

• Code: 012-151
• Description: (A-Finisher) Compiler Exit Sensor OFF Jam The Compile Exit Sensor does not turn Off within a specified time after it has turned On.
• Remedy: Check the specifications of paper. Paper is in spec. Y↓N→Replace the paper with new paper that is in spec. Check the condition of the paper. The paper is in normal condition without any problem that causes the paper to be bent or caught. Y↓N→Resolve any problem that causes the paper to be bent or caught. Check the transport path for a foreign object, deformed part, and paper dust. The transport path is in normal condition with no foreign object, deformed part and paper dust. Y↓N→Repair the deformed part(s) and remove the foreign object(s) and paper dust. Check the Transport Roll for wear, deterioration and paper dust. The Transport Roll is in normal condition, not worn and deteriorated and with no paper dust. Y↓N→Remove the paper dust and replace the worn or deteriorated Transport Roll. Check the drive mechanism to the Transport Roll for a deformed, broken part, and/or belt damage. The drive mechanism is free of defects. Y↓N→Repair defects or damage to the drive mechanism. Enter Component Control [012-150]. Actuate the Compile Exit Sensor. The display changes. Y↓N→Check the connections of P/J8709 and P/J8728. P/J8709 and P/J8728 are securely connected. Y↓N→Connect P/J8709 and P/J8728 securely. Check for an open or short circuit between J8709 and J8728. The wire J8709 and J8728 are OK. Y↓N→Repair the open or short circuit. Measure the voltage between Finisher PWB J8709-3 (+) and GND (-). The voltage is approx. +5VDC. Y↓N→Go to Wirenet A-Finisher +5VDC and check the +5VDC circuit. Measure the voltage between Finisher PWB J8709-2 (+) and GND (-). Actuate the Compile Exit Sensor. The voltage changes. Y↓N→Replace the Compile Exit Sensor (PL 22.5). Check the wires and connectors for an intermittent open or short circuit. If the problem continues, replace the Finisher PWB (PL 22.7). Enter Component Control [012-095]. The Finisher Transport Motor rotates. Y↓N→Check the connections of P/J8706 and P/J8739. P/J8706 and P/J8739 are securely connected. Y↓N→Connect P/J8706 and P/J8739 securely. Check for an open or short circuit between J8706 and J8736. The wire between J8706 and J8736 are OK. Y↓N→Repair the open or short circuit. Measure the voltage between Finisher PWB J8706-5 (+) and GND (-), and between Finisher PWB J8706-7 (+) and GND (-). Each voltage is approx. +24VDC. Y↓N→Go to Wirenet A-Finisher +24VDC and check the +24VDC circuit. Check the wires and connectors for an intermittent open or short circuit. If the problem continues, replace the Finisher Transport Motor (PL 22.4). If the problem persists, replace the Finisher PWB (PL 22.7). Enter [012-013]. When the Sub Paddle Solenoid is turned On/Off, the Sub Paddle Shaft Assembly goes down/up. Y↓N→Check the Sub Paddle mechanism for a deformed or broken part and not-seated gears. The Sub Paddle mechanism is free from defects and gears are seating properly. Y↓N→Repair defeats to the Sub Paddle mechanism. Check the connections of P/J8705 and P/J8734. P/J8705 and P/J8734 are securely connected. Y↓N→Connect P/J8705 and P/J8734 securely. Check for an open or short circuit between J8705 and J8734. The wires between J8705 and J8734 are OK. Y↓N→Repair the open or short circuit. Measure the voltage between Finisher PWB J8705-1 (+) and GND (-). The voltage is approx. +24VDC. Y↓N→Go to Wirenet A-Finisher +24VDC and check the +24VDC circuit. If the circuit is OK, replace the Finisher PWB (PL 22.7). Enter [012-013], measure the voltage between Finisher PWB J8705-2 (+) and GND (-). The voltage changes. Y↓N→Replace the Finisher PWB (PL 22.7). Replace the Sub Paddle Solenoid (PL 22.3). Check the wires and connectors for an intermittent open or short circuit. If the problem continues, replace the Finisher PWB (PL 22.7).

• Code: 012-151
• Description: Compile Exit Sensor Off JAM RAP After the Compile Exit Sensor turned On, the Compile Exit Sensor did not turn Off within the specified time.
• Remedy: Check the Transport Roll for wear and paper powder. The Transport Roll is ok. Y↓N→Replace the Transport Roll. Check for foreign substances, distortion and paper powder in the paper transport path. No distortion, foreign substances, or paper powder are found in the paper transport path. Y↓N→Clear away the foreign substances and paper powder. Correct the distortion. Execute Component Control[012-150 Compile Exit Sensor]. Actuate the Compile Exit Sensor with paper. The display changes. Y↓N→Check the connections of J8869 and P/J8988. J8869 and P/J8988 are connected correctly. Y↓N→Connect J8869 and P/J8988. Check the wire between J8869 and J8988 for an open circuit or a short circuit. The wire between J8869 and J8988 is conducting without an open circuit or a short circuit. Y↓N→Repair the open circuit or short circuit. Measure the voltage between the Finisher PWB P8988-6 (+) and GND (-). The voltage is approx. +5VDC. Y↓N→Replace the Finisher PWB (PL 23.16). Measure the voltage between the Finisher PWB P8988-5 (+) and GND (-). Actuate the Compile Entrance Sensor with paper. The voltage changes. Y↓N→Replace the Compile Entrance Sensor (PL 23.14). Replace the Finisher PWB (PL 23.16). Execute Component Control[012-038 Transport Motor ON]. The Transport Motor can be heard. Y↓N→Check the connections of P/J8879 and P/J8983. P/J8879 and P/J8983 are connected correctly. Y↓N→Connect P/J8879 and P/J8983. Check the wire between J8879 and J8983 for an open circuit or a short circuit. The wire between J8879 and J8983 is conducting without an open circuit or a short circuit. Y↓N→Repair the open circuit or short circuit. Measure the resistance of the Transport Motor (PL 23.13) wires between each point of J8879-1/2/5/6. The resistance is approx. 20Ohm. Y↓N→Replace the Transport Motor (PL 23.13). Measure the voltage between each point of the Finisher PWB (PL 23.16) P8983-9/10/11/ 12 (+) and GND (-). The voltage is approx. +24VDC. Y↓N→Replace the Finisher PWB (PL 23.16). Replace the Transport Motor (PL 23.13). If the problem persists, replace the Finisher PWB (PL 23.16). Replace the Finisher PWB (PL 23.16).

• Code: 012-152
• Description: (A-Finisher) Compiler Exit Sensor ON Jam The Compile Exit Sensor does not turn On within a specified time after receiving the Sheet Exit command (the paper to be ejected has turned On the IOT Exit Sensor 1).
• Remedy: Check the specifications of paper. Paper is in spec. Y↓N→Replace the paper with new paper that is ins spec. Check the condition of the paper. The paper is in normal condition without any problem that causes the paper to be bent or caught. Y↓N→Resolve any problem that causes the paper to be bent or caught. Check the transport path for a foreign object, deformed part, and paper dust. The transport path is in normal condition with no foreign object, deformed part and paper dust. Y↓N→Repair the deformed part(s) and remove the foreign object(s) and paper dust. Check the Transport Roll for wear, deterioration and paper dust. The Transport Roll is in normal condition. Y↓N→Remove the paper dust and replace the worn or deteriorated Transport Roll. Check the drive mechanism to the Transport Roll for a deformed parts, broken parts, and/or belt damage. The drive mechanism free from defects. Y↓N→Repair defects or damage to the drive mechanism. Check that the Finisher is installed properly. The Finisher is properly installed and properly connected to the IOT. Y↓N→Reinstall the Finisher properly. Enter Component Control [012-150]. Actuate the Compile Exit Sensor. The display changes. Y↓N→Check the connections of P/J8709 and P/J8728. P/J8709 and P/J8728 are securely connected. Y↓N→Connect P/J8709 and P/J8728 securely. Check for an open or short circuit between J8709 and J8728. The wires between J 8709 and J8728 are OK. Y↓N→Repair the open or short circuit. Measure the voltage between Finisher PWB J8709-3 (+) and GND (-). The voltage is approx. +5VDC. Y↓N→Go to Wirenet A-Finisher +5VDC and check the +5VDC circuit. Measure the voltage between Finisher PWB J8709-2 (+) and GND (-). Actuate the Compile Exit Sensor. The voltage normally changes. Y↓N→Replace the Compile Exit Sensor (PL 22.5). Check the wires and connectors for an intermittent open or short circuit. If the problem continues, replace the Finisher PWB (PL 22.7). Enter [012-095]. The Finisher Transport Motor rotates. Y↓N→Check the connections of P/J8706 and P/J8739. P/J8706 and P/J8739 are securely connected. Y↓N→Connect P/J8706 and P/J8739 securely. Check for an open or short circuit between J8706 and J8739. The wire between J8706 and J8739 are OK. Y↓N→Repair the open or short circuit. Measure the voltage between Finisher PWB J8706-5 (+) and GND (-), and J8706-7 (+) and GND (-). Each voltage is approx. +24VDC. Y↓N→Go to Wirenet A-Finisher +24VDC and check the +24VDC circuit. Check the wires and connectors for an intermittent open or short circuit. If the problem continues, replace the Finisher Transport Motor (PL 22.4). If the problem persists, replace the Finisher PWB (PL 22.7). Check the wires and connectors for an intermittent open or short circuit. If the problem continues, replace the Finisher PWB (PL 22.7).

• Code: 012-152
• Description: Compile Exit Sensor On JAM RAP After the H-Transport Exit Sensor turned On, the Compile Exit Sensor did not turn On within the specified time.
• Remedy: Check the Transport Roll for wear and paper powder. The Transport Roll is ok. Y↓N→Replace the Transport Roll. Check for foreign substances, distortion and paper powder in the paper transport path. No distortion, foreign substances, or paper powder are found in the paper transport path. Y↓N→Clear away the foreign substances and paper powder. Correct the distortion. Execute Component Control[012-150 Compile Exit Sensor]. Actuate the Compile Exit Sensor with paper. The display changes. Y↓N→Check the connections of J8869 and P/J8988. J8869 and P/J8988 are connected correctly. Y↓N→Connect J8869 and P/J8988. Check the wire between J8869 and J8988 for an open circuit or a short circuit. The wire between J8869 and J8988 is conducting without an open circuit or a short circuit. Y↓N→Repair the open circuit or short circuit. Measure the voltage between the Finisher PWB P8988-6 (+) and GND (-). The voltage is approx. +5VDC. Y↓N→Replace the Finisher PWB (PL 23.16). Measure the voltage between the Finisher PWB P8988-5 (+) and GND (-). Actuate the Compile Entrance Sensor with paper. The voltage changes. Y↓N→Replace the Compile Entrance Sensor (PL 23.14). Replace the Finisher PWB (PL 23.16). Execute Component Control[012-038 Transport Motor ON]. The Transport Motor can be heard. Y↓N→Check the connections of P/J8879 and P/J8983. P/J8879 and P/J8983 are connected correctly. Y↓N→Connect P/J8879 and P/J8983. Check the wire between J8879 and J8983 for an open circuit or a short circuit. The wire between J8879 and J8983 is conducting without an open circuit or a short circuit. Y↓N→Repair the open circuit or short circuit. Measure the resistance of the Transport Motor (PL 23.13) wires between each point of J8879-1/2/5/6. The resistance is approx. 20Ohm. Y↓N→Replace the Transport Motor (PL 23.13). Measure the voltage between each point of the Finisher PWB (PL 23.16) P8983-9/10/11/ 12 (+) and GND (-). The voltage is approx. +24VDC. Y↓N→Replace the Finisher PWB (PL 23.16). Replace the Transport Motor (PL 23.13). If the problem persists, replace the Finisher PWB (PL 23.16). Replace the Finisher PWB (PL 23.16).