Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Xerox WorkCentre 5645 — Trang 27/30

Code: 11-392-171 ... 11-395-171

Description: HVF Front Tamper Tray RAP 11-392-171 The front tamper tray did not move from the home position. 11-393-171 The front tamper tray did not return to the home position. 11-394-171 The front tamper tray did not enter the away position. 11-395-171 The front tamper tray did not move from the away position.
Remedy: shows the location of the components. Enter dC330, code 11-003 to move the tamper inboard, and enter 11-005 to move the tamper outboard. The tamper moves. Y↓N→Go to Flag 1. Check the wiring and repair as necessary. Check the front tamper motor, MOT11-003. Refer to: • GP 10 How to Check a Motor. • P/J902 HVF PWB. • 11A-171 HVF Power Distribution RAP. Install new components as necessary: • Front tamper motor, MOT11-003, PL 11.153 Item 6. • HVF control PWB, PL 11.157 Item 2. Stack the dC330 code 11-310, front tamper home sensor. Move the motor using its control code 11-003 or 11-005. The display changes. Y↓N→Go to Flag 2. Check the wiring and repair as necessary. Check the front tamper home sensor, Q11-310. Refer to: • GP 11 How to Check a Sensor. • P/J901 HVF control PWB. • 11A-171 HVF Power Distribution RAP. Install new components as necessary: • Front tamper home sensor, Q11-310, PL 11.153. • HVF control PWB, PL 11.157 Item 2. Stack the dC330 code 11-174, front tamper away sensor. Move the motor using its control code 11-003 or 11-005. The display changes. Y↓N→Go to Flag 3. Check the wiring and repair as necessary. Check the front tamper away sensor, Q11-174. Refer to: • GP 11 How to Check a Sensor. • P/J901 HVF control PWB. • 11A-171 HVF Power Distribution RAP. Install new components as necessary: • Front tamper away sensor, Q11-174, PL 11.153. • HVF control PWB, PL 11.157 Item 2. Perform SCP 6 Final Actions.

Code: 11-396-171 ... 11-399-171

Description: HVF Rear Tamper Tray RAP 11-396-171 The rear tamper tray did not move from the home position. 11-397-171 The rear tamper tray did not return to the home position. 11-398-171 The rear tamper tray did not move from the away position. 11-399-171 The rear tamper tray did not return to the away position.
Remedy: Enter the dC330 code, 11-006, move rear tamper inboard. The tamper moves. Y↓N→Go to Flag 1. Check the wiring and repair as necessary. Check the rear tamper motor, MOT11-004. Refer to: • GP 10 How to Check a Motor. • P/J801 HVF control PWB. • 11A-171 HVF Power Distribution RAP. Install new components as necessary: • Rear tamper motor, MOT11-004, PL 11.140. • HVF control PWB, PL 11.157 Item 2. Stack the dC330 code, 11-311, rear tamper home sensor. Move the tamper motor using the code 11-006, move motor inboard. The display changes. Y↓N→Go to Flag 2. Check the wiring and repair as necessary. Check the rear tamper home sensor, Q11-311. Refer to: • GP 11 How to Check a Sensor. • P/J401 HVF control PWB. • 11A-171 HVF Power Distribution RAP. Install new components as necessary: • Rear tamper home sensor, Q11-311, PL 11.140. • HVF control PWB, PL 11.157 Item 2. Enter the dC330 code, 11-319, rear tamper away sensor. Actuate the rear tamper away sensor, using a piece of paper inserted from the rear of the machine. The display changes. Y↓N→Go to Flag 3. Check the wiring and repair as necessary. Check the rear tamper away sensor, Q11-319. Refer to: • GP 11 How to check a sensor. • P/J401 HVF control PWB. • 11A-171 HVF Power Distribution RAP. Install new components as necessary: • Rear tamper away sensor, Q11319, PL 11.140. • HVF control PWB, PL 11.157 Item 2. Perform SCP 6 Final Actions.

Code: 11-403-170, 11-413-170

Description: HCSS BM Staple Unit 2 Failure RAP 11-403-170 The HCSS BM staple unit 2 fails to move. 11-413-170 The HCSS BM staple unit 2 is not at the home position
Remedy: Enter dC330, code 11-421 to check the BM staple head carrier closed sensor, Q11-421. Open and close the staple head carrier. The display changes. Y↓N→Go to Flag 1, check the staple head carrier closed sensor, Q11-421. Refer to: • GP 11, How to Check a Sensor. • P/J552, BM PWB. • 11C-170 HCSS BM Power Distribution RAP. Install new components as necessary: • BM staple head carrier closed sensor, PL 11.88 Item 18. • BM PWB, PL 11.86 Item 10. Enter dC330, code 11-403 to run the BM SH2 motor, stack the code 11-413 to check the BM SH2 home switch. The display changes. Y↓N→The staple head cycled when the first code was entered. Y↓N→Go to Flag 3 and check the wiring and connectors between P/J560 and PJ586. The wiring and connectors are good. Y↓N→Repair the wiring or connectors. Install a new BM staple head 2, PL 11.88 Item 7. Go to Flag 2, check the BM SH2 home switch, S11-413. Refer to: • GP 13, How to Check a Switch. • P/J551, BM PWB. • 11C-170 HCSS BM Power Distribution RAP. Install new components as necessary: • BM staple head 2, PL 11.88 Item 7. • BM PWB, PL 11.86 Item 10. The fault may be intermittent, check for damaged wiring or bad connectors. If necessary install new components: • BM staple head carrier closed sensor, PL 11.88 Item 18. • BM staple head 2, PL 11.88 Item 7. • BM PWB, PL 11.86 Item 10.

Code: 11-403-171, 11-413-171, 11-414-171

Description: HVF BM Staple Head 2 and Stapler Module RAP 11-403-171 The booklet maker staple head 2 motor has failed to move. 11-413-171 The booklet maker staple head 2 is not detected in the home position. 11-414-171 The booklet maker stapler module is not detected in the home (staple head closed) position during hard / soft initialize, or at set boundary.
Remedy: Enter dC330, code 11-421 to check the BM staple head carrier closed sensor, Q11-421. Open and close the staple head carrier. The display changes. Y↓N→Go to Flag 1, check the staple head carrier closed sensor, Q11-421. Refer to: • GP 11, How to Check a Sensor. • P/J552, BM PWB. • 11A-171 HVF BM Power Distribution RAP. Install new components as necessary: • BM staple head carrier closed sensor, PL 11.168. • BM PWB, PL 11.166 Item 10. Enter dC330, code 11-403 to run the BM SH2 motor, stack the code 11-413 to check the BM SH2 home switch. The display changes. Y↓N→The staple head cycled when the first code was entered. Y↓N→Go to Flag 3 and check the wiring and connectors between P/J560 and PJ586. The wiring and connectors are good. Y↓N→Repair the wiring or connectors. Install a new BM staple head 2, PL 11.168 Item 11. Go to Flag 2, check the BM SH2 home switch, S11-413. Refer to: • GP 13, How to Check a Switch. • P/J551, BM PWB. • 11A-171 HVF BM Power Distribution RAP. Install new components as necessary: • BM staple head 2, PL 11.168 Item 11. • BM PWB, PL 11.166 Item 10. The fault may be intermittent, check for damaged wiring or bad connectors. If necessary install new components: • BM staple head carrier closed sensor, PL 11.168 Item 18. • BM staple head 2, PL 11.168 Item 11. • BM PWB, PL 11.166 Item 10.

Code: 11-415-170

Description: HCSS BM Crease Roll Gate Failure RAP 11-415-170 The HCSS crease roll gate is not at the home position.
Remedy: Enter dC330 code 11-415. Actuate the BM crease roll gate home sensor, Q11-415. The display changes. Y↓N→Go to Flag 1, check the BM crease roll gate home sensor, Q11-415. Refer to: • GP 11, How to Check a Sensor. • P/J552, BM PWB. • 11C-170 HCSS BM Power Distribution RAP. Install new components as necessary: • BM PWB, PL 11.86 Item 10. • BM crease roll gate home sensor PL 11.86 Item 9. Enter dC330, code 11-401 to run the BM crease roll gate motor, MOT 11-401. The motor runs. Y↓N→Go to Flag 2 and Flag 3, check the BM crease roll gate motor, MOT 11-401. Refer to: • GP 10 How to Check a Motor. • P/J555, BM PWB. • 11C-170 HCSS BM Power Distribution RAP. Install new components as necessary: • BM PWB, PL 11.86 Item 10. • BM crease roll gate motor, PL 11.86 Item 8. The fault may be intermittent, check for damaged wiring or bad connectors. If necessary install a new BM PWB, PL 11.86 Item 10.

Code: 11-415-171

Description: HVF BM Crease Roll Gate Home RAP 11-415-171 The crease roll gate is not at the home position.
Remedy: Enter dC330 code 11-415. Actuate the BM crease roll gate home sensor, Q11-415. The display changes. Y↓N→Go to Flag 1, check the BM crease roll gate home sensor, Q11-415. Refer to: • GP 11, How to Check a Sensor. • P/J552, BM PWB. • 11A-171 HVF BM Power Distribution RAP. Install new components as necessary: • BM PWB, PL 11.166 Item 10. • BM crease roll gate home sensor PL 11.166 Item 9. Enter dC330, code 11-401 to run the BM crease roll gate motor, MOT 11-401. The motor runs. Y↓N→Go to Flag 2 and Flag 3, check the BM crease roll gate motor, MOT 11-401. Refer to: • GP 10 How to Check a Motor. • P/J555, BM PWB. • 11A-171 HVF BM Power Distribution RAP. Install new components as necessary: • BM PWB, PL 11.166 Item 10. • BM crease roll gate motor, PL 11.166 Item 8. The fault may be intermittent, check for damaged wiring or bad connectors. If necessary install a new BM PWB, PL 11.166 Item 10.

Code: 11-417-171, 11-418-171

Description: HVF BM Flapper RAP 11-417-171 The booklet maker flapper did not return to the home position. 11-418-171 The booklet maker flapper did not move from the home position.
Remedy: NOTE: All HVF BM interlocks must be made to supply +24V to the motors. Enter dC330, code 11-390 to check the BM flapper motor, MOT11-390. The BM flapper rotates. Y↓N→Go to Flag 2. Check MOT11-390. Refer to: • GP 10, How to Check a Motor. • P/J560, BM PWB. • 11A-171, HVF BM Power Distribution RAP. Install new components as necessary: • BM flapper motor, PL 11.161 Item 28. • BM PWB, PL 11.166 Item 10. • BM flapper, PL 11.161 Item 23. Enter dC330, code 11-391. Actuate the flapper home sensor, Q11-391. The display changes. Y↓N→Go to Flag 1. Check Q11-391. Refer to: • GP 11 How to Check a Sensor. • P/J551, BM PWB. • 11A-171, HVF BM Power Distribution RAP. Install new components as necessary: • Flapper home sensor, PL 11.161 Item 12. • BM PWB, PL 11.166 Item 10. Perform SCP 6 Final Actions.

Code: 11-430-130

Description: Kicker Failed to Complete Cycle RAP 11-430-130 The kicker failed to complete a cycle, either to extend or retract.
Remedy: Check the following: • If the kicker fingers are jammed against the left side of bin 1 or bin 2, perform the following: For Bin 1: 1. Enter dC330, code 11-031 bin 1 elevator motor up. Fully raise bin 1. 2. Remove the bin 1 thumbscrew, PL 11.52 Item 12. 3. Pull the bin 1 tray assembly, PL 11.52 Item 10 away from the machine until the kicker fingers are released. 4. Re-install the bin 1 tray assembly then the thumbscrew. 5. Enter code 11-032 bin 1 elevator motor down. Lower bin 1 approximately 100mm (4 inches). For Bin 2: 1. Enter dC330, code 11-037 bin 2 elevator motor up. Fully raise bin 2. 2. Remove the bin 2 thumbscrew, PL 11.54 Item 15. 3. Pull the bin 2 tray assembly, PL 11.54 Item 10 away from the machine until the kicker fingers are released. 4. Re-install the bin 2 tray assembly then the thumbscrew. 5. Enter code 11-038 bin 2 elevator motor down. Lower bin 2 approximately 100mm (4 inches). • The kicker fingers, PL 11.49 Item 19, for damage, paper debris or other obstructions that would prevent operation. • The kicker frame, PL 11.49 Item 14, for damage or other obstructions that would prevent operation. • If there is a high level of static on the sheets or the stack. Check that the following static eliminators are grounded and in good condition: – Static eliminator, PL 11.32 Item 5. – Static eliminator (part of eject housing), PL 11.47 Item 10. • If the output sheets are curled, go to IQ5 Print Damage RAP. • If the output stacking is poor, go to the 11G-130 HCSS Poor Stacking RAP. • Kicker failures can be caused by large sheets being stacked over small sheets, Advise the customer to clear the bins before following a small sheet job with a large sheet job.
Enter dC330, code 11-313., pull down, then release the kicker fingers to actuate the compiler carriage 90% full sensor, Q11-313. The display changes. Y↓N→Go to Flag 1. Check the sensor. Refer to: • GP 11 How to Check a Sensor. • P/J407, Carriage PWB. • 11C-130 HCSS Power Distribution RAP. Install new components as necessary: • Carriage PWB, PL 11.46 Item 5. • Compiler carriage 90% full sensor, PL 11.49 Item 5. Enter dC330, code 11-314., pull down, then release the kicker fingers, to actuate the compiler carriage bin height sensor, Q11-314. The display changes. Y↓N→Go to Flag 2. Check the sensor. Refer to: • GP 11 How to Check a Sensor. • P/J407, Carriage PWB. • 11C-130 HCSS Power Distribution RAP. Install new components as necessary: • Carriage PWB, PL 11.46 Item 5. • Compiler carriage bin height sensor, PL 11.49 Item 5. Enter dC330, code 11-430, to energise the kicker solenoid SOL 11-430. The solenoid energises. Y↓N→Go to Flag 3. Check the solenoid. Refer to: • GP 12 How to Check a Solenoid or Clutch. • P/J402, Carriage PWB. • 11C-130 HCSS Power Distribution RAP. Install new components as necessary: • Carriage PWB, PL 11.46 Item 5. • Kicker solenoid, PL 11.49 Item 4. Go to the 11-120-130, 11-122-130 Compiler Carriage Jam RAP, and check the compiler sensor Q11-120. If the fault still occurs or is intermittent, install a new kicker assembly, PL 11.49 Item 15.
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie