Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Xerox WorkCentre 5655 — Trang 14/30

Code: 11-005-120, 11-006-120, 11-310-120, 11-311-120

Description: Front Tamper Move Failure RAP 11-005-120 Front tamper fails to move to the front position. 11-006-120 Front tamper fails to move to the rear position. 11-310-120 Front tamper not at the front home position. 11-311-120 Front tamper not at the rear home position.
Remedy: NOTE: All 1K LCSS interlocks must be made to supply +24V to the motors. NOTE: In diagnostics, actuating any 1K LCSS sensor or switch can change the displayed state on the UI. Make sure that the correct sensor or switch is tested. Enter dC330, codes 11-003 and 11-005 alternately. The front tamper moves between the home and inboard positions. Y↓N→Go to Flag 2. Check the front tamper motor, MOT11-003. Refer to: • 11G-120 1K LCSS PWB Damage RAP. • GP 10 How to Check a Motor. • P/J9, 1K LCSS PWB. • 11C-120 1K LCSS Power Distribution RAP. Repair or install new components as necessary: • Tamper assembly, PL 11.112 Item 1. • 1K LCSS PWB, PL 11.124 Item 1. Enter dC330 code 11-310. Actuate the front tamper home sensor, Q11-310. The display changes. Y↓N→Go to Flag 1. Check Q11-310. Refer to: • 11F-120 1K LCSS PWB Damage RAP. • GP 11 How to Check a Sensor. • P/J16, 1K LCSS PWB. • 11C-120 1K LCSS Power Distribution RAP. Repair or install new components as necessary: • Front tamper home sensor, PL 11.112 Item 3. • 1K LCSS PWB, PL 11.124 Item 1. Perform SCP 6 Final Actions.

Code: 11-005-130, 11-006-130, 11-310-130, 11-311-130

Description: Front Tamper Move Failure RAP 11-005-130 The front tamper fails to move to the front position. 11-006-130 The front tamper fails to move to the rear position. 11-310-130 The front tamper is not at the front home position. 11-311-130 The front tamper is not at the rear home position. NOTE: The home position is the outermost position.
Remedy: NOTE: All HCSS interlocks must be made to supply +24V to the motors. Enter dC330, codes 11-005 tamper motor front move, then 11-003 tamper motor front home. The front tamper moves between the inboard and home positions. Y↓N→Go to Flag 2. Check the motor, MOT11-003. Refer to: • GP 10, How to Check a Motor. • P/J404, Carriage PWB. • 11C-130, HCSS Power Distribution RAP. Install new components as necessary: • Carriage PWB, PL 11.46 Item 5. • Front tamper motor, PL 11.46 Item 10. Enter dC330, code 11-310, actuate the front tamper home sensor by using the stacked codes, 11-003 and 11-005 to move the tamper. Observe the display. The display changes. Y↓N→Go to Flag 1. Check the sensor, Q11-310. Refer to: • GP 11 How to Check a Sensor. • P/J407, Carriage PWB. • 11C-130, HCSS Power Distribution RAP. Install new components as necessary: • Carriage PWB, PL 11.46 Item 5. • Compiler carriage assembly, PL 11.46 Item 1. Go to Flag 3. Check the harness and connectors P/J412 and P/J432. Also check the harness and connectors P/J401 and P/J428, refer to GP 7. The wiring and connectors are good. Y↓N→Repair the wiring or install new components as necessary, PL 11.46.

Code: 11-005-170, 11-006-170, 11-310-170, 11-311-170

Description: Compiler Carriage Front Tamper Move Failure RAP 11-005-170 The compiler carriage front tamper fails to move to the front position. 11-006-170 The compiler carriage front tamper fails to move to the rear position 11-310-170 The compiler carriage front tamper is not at the front home position. 11-311-170 The compiler carriage front tamper is not at the rear home position.
Remedy: NOTE: All HCSS BM interlocks must be made to supply +24V to the motors. Enter dC330, codes 11-005 tamper motor front move, then 11-003 tamper motor front home. The front tamper moves between the inboard and home positions. Y↓N→Go to Flag 2. Check the motor, MOT11-003. Refer to: • GP 10, How to Check a Motor. • P/J404, Carriage PWB. • 11C-170 HCSS BM Power Distribution RAP. Install new components as necessary: • Carriage PWB, PL 11.72 Item 5. • Front tamper motor, PL 11.72 Item 10. Enter dC330, code 11-310, actuate the front tamper home sensor by using the stacked codes, 11-003 and 11-005 to move the tamper. Observe the display. The display changes. Y↓N→Go to Flag 1. Check the sensor, Q11-310. Refer to: • GP 11 How to Check a Sensor. • P/J407, Carriage PWB. • 11C-170, HCSS BM Power Distribution RAP. Install new components as necessary: • Carriage PWB, PL 11.72 Item 5. • Compiler carriage assembly, PL 11.72 Item 1. Go to Flag 3. Check the connectors and harness between P/J412 and P/J432. Also check the connectors and harness between P/J401 and P/J428, refer to GP 7. The wiring and connectors are good. Y↓N→Repair the wiring, or install new components as necessary.

Code: 11-007-110, 11-008-110, 11-312-110, 11-313-110, 11-319-110

Description: Rear Tamper Move Failure RAP 11-007-110 Rear tamper fails to move to the front position. 11-008-110 Rear tamper fails to move to the rear position. 11-312-110 Rear tamper is not at the front home position. 11-313-110 Rear tamper is not at the rear home position. 11-319-110 Rear tamper is not at the away home position. NOTE: The away home position is with the rear tamper approximately halfway along it’s travel.
Remedy: •. Check for damage or obstructions that would prevent the tamper assembly from operating correctly. If necessary, install a new tamper assembly, PL 11.16 Item 1. • Jams can be caused by removing prints from bin 1 before the machine has finished printing. If the tampers are touched while they are moving, they may stall and cause the machine to shutdown. The resulting shutdown can cause un-clearable jams in the finisher and the tray 3 and tray 4 to paper path interface. • Jams can also be caused if the tray settings do not match the paper in the trays. Make sure the tray settings are correct. • Check the condition of the front tamper drive belt and that it is correctly tensioned. Tensioning is achieved by a spring on the motor, the motor should be free to move. • If there is a large jam of paper above bin 1 that has obstructed the tampers, this has probably been caused by poorly stacked sets failing to actuate the bin 1 upper level sensor. Perform the following: – Check the paper for defects that could degrade the tamping operation e.g. curl, paper condition, buckling or paper type. Refer to IQ1 Image Quality Entry RAP. – Check the operation of the paddle roll, refer to 11-024-110, 11-025-110 Paddle Roll Failure RAP. – Check the operation of the bin 1 upper level sensor, refer to 11-030-110, 11-334-110, 11-335-110, 11-336-110 Bin 1 Movement Failure RAP. – Refer to the 11J-110 Mis-Registration in Stapled Sets and Non-Stapled Sets RAP. – Check the 2K LCSS PWB DIP switch settings, refer to 11F-110 2K LCSS PWB DIP Switch Settings RAP.
NOTE: All 2K LCSS interlocks must be made to supply +24V to the motors. NOTE: In diagnostics, actuating any 2K LCSS sensor or switch can change the displayed state on the UI. Make sure that the correct sensor or switch is tested. Enter dC330, codes 11-004 and 11-006 alternately. The rear tamper moves between the home and inboard positions. Y↓N→Go to Flag 3. Check the rear tamper motor, MOT11-004. Refer to: • 11G-110 2K LCSS PWB Damage RAP. • GP 10, How to Check a Motor. • P/J312, 2K LCSS PWB. • 11D-110 2K LCSS Power Distribution RAP. Repair or install new components as necessary: • Tamper assembly, PL 11.16 Item 1. • 2K LCSS PWB, PL 11.26 Item 1. Enter dC330 code 11-311, actuate the rear tamper home sensor Q11-311. The display changes. Y↓N→Go to Flag 1 and check Q11-311. Refer to: • 11G-110 2K LCSS PWB Damage RAP. • GP 11, How to Check a Sensor. • P/J312, 2K LCSS PWB. • 11D-110 2K LCSS Power Distribution RAP. Repair or install new components as necessary: • Rear tamper home sensor, PL 11.16 Item 3. • 2K LCSS PWB, PL 11.26 Item 1. NOTE: The away home position is used for short edge feed small paper. This saves unnecessary rear tamper travel. Enter dC330, actuate the rear tamper away home sensor Q11-319. The display changes. Y↓N→Go to Flag 2 and check Q11-319. Refer to: • 11G-110 2K LCSS PWB Damage RAP. • GP 11, How to Check a Sensor. • P/J312, 2K LCSS PWB. • 11D-110 2K LCSS Power Distribution RAP. Repair or install new components as necessary: • Rear tamper away home sensor, PL 11.16 Item 3. • 2K LCSS PWB, PL 11.26 Item 1. Perform SCP 6 Final Actions.

Code: 11-007-120, 11-008-120, 11-312-120, 11-313-120, 11-319-120

Description: Rear Tamper Move Failure RAP 11-007-120 Rear tamper fails to move to the front position. 11-008-120 Rear tamper fails to move to the rear position. 11-312-120 Rear tamper is not at the front home position. 11-313-120 Rear tamper is not at the rear home position. 11-319-120 Rear tamper is not at the away home position.
Remedy: NOTE: All 1K LCSS interlocks must be made to supply +24V to the motors. NOTE: In diagnostics, actuating any 1K LCSS sensor or switch can change the displayed state on the UI. Make sure that the correct sensor or switch is tested. Enter dC330, codes 11-004 and 11-006 alternately. The rear tamper moves between the home and inboard positions. Y↓N→Go to Flag 3. Check the rear tamper motor, MOT11-004. Refer to: • 11F-120 1K LCSS PWB Damage RAP. • GP 10, How to Check a Motor. • P/J9, 1K LCSS PWB. • 11C-120 1K LCSS Power Distribution RAP. Repair or install new components as necessary: • Tamper assembly, PL 11.112 Item 1. • 1K LCSS PWB, PL 11.124 Item 1. Enter dC330 code 11-311. Actuate the rear tamper home sensor Q11-311. The display changes. Y↓N→Go to Flag 1. Check Q11-311. Refer to: • 11F-120 1K LCSS PWB Damage RAP. • GP 11, How to Check a Sensor. • P/J16, 1K LCSS PWB • 11C-120 1K LCSS Power Distribution RAP. Repair or install new components as necessary: • Rear tamper home sensor, PL 11.112 Item 3. • 1K LCSS PWB, PL 11.124 Item 1. NOTE: The away home position is used for short edge feed small paper. This saves unnecessary rear tamper travel. Enter dC330. Actuate the rear tamper away home sensor Q11-319. The display changes. Y↓N→Go to Flag 2. Check Q11-319. Refer to: • 11F-120 1K LCSS PWB Damage RAP. • GP 11, How to Check a Sensor. • P/J16, 1K LCSS PWB • 11C-120 1K LCSS Power Distribution RAP. Repair or install new components as necessary: • Rear tamper away home sensor, PL 11.112 Item 3. • 1K LCSS PWB, PL 11.124 Item 1. Perform SCP 6 Final Actions.

Code: 11-007-130, 11-008-130, 11-312-130, 11-313-130

Description: Rear Tamper Move Failure RAP 11-007-130 The rear tamper fails to move to the front position. 11-008-130 The rear tamper fails to move to the rear position. 11-312-130 The rear tamper is not at the front home position. 11-313-130 The rear tamper is not at the rear home position. NOTE: The home position is the outermost position.
Remedy: NOTE: All HCSS interlocks must be made to supply +24V to the motors. Enter dC330, codes 11-006 tamper motor rear move, then 11-004 tamper motor rear home. The rear tamper moves between the inboard and home positions. Y↓N→Go to Flag 2. Check the motor, MOT11-004. Refer to: • GP 10, How to Check a Motor. • P/J402, Carriage PWB. • 11C-130 HCSS Power Distribution RAP. Install new components as necessary: • Carriage PWB, PL 11.46 Item 5. • Rear tamper motor, PL 11.46 Item 10. Enter dC330, code 11-311, actuate the front tamper home sensor by using the stacked codes, 11-004 and 11-006 to move the tamper. Observe the display. The display changes. Y↓N→Go to Flag 1. Check the sensor, Q11-311. Refer to: • GP 11 How to Check a Sensor. • P/J407, Carriage PWB. • 11C-130 HCSS Power Distribution RAP. Install new components as necessary: • Carriage PWB, PL 11.46 Item 5. • Compiler carriage assembly, PL11.46/1. Go to Flag 3. Check the harness and connectors P/J412 and P/J432. Also, check the harness and connectors P/J401 and P/J428, refer to GP 7. The wiring and connectors are good. Y↓N→Repair the wiring or install new components as necessary.

Code: 11-007-170, 11-008-170, 11-312-170, 11-313-170

Description: Compiler Carriage Rear Tamper Move Failure RAP 11-007-170 The compiler carriage rear tamper fails to move to the front position. 11-008-170 The compiler carriage rear tamper fails to move to the rear position 11-312-170 The compiler carriage rear tamper is not at the front home position. 11-313-170 The compiler carriage rear tamper is not at the rear home position
Remedy: NOTE: All HCSS BM interlocks must be made to supply +24V to the motors. Enter dC330, codes 11-006 tamper motor rear move, then 11-004 tamper motor rear home. The rear tamper moves between the inboard and home positions. Y↓N→Go to Flag 2. Check the motor, MOT11-004. Refer to: • GP 10, How to Check a Motor. • P/J402, Carriage PWB. • 11C-170 HCSS BM Power Distribution RAP. Install new components as necessary: • Carriage PWB, PL 11.72 Item 5. • Rear tamper motor, PL 11.72 Item 10. Enter dC330, code 11-311, actuate the front tamper home sensor by using the stacked codes, 11-004 and 11-006 to move the tamper. Observe the display. The display changes. Y↓N→Go to Flag 1. Check the sensor, Q11-311. Refer to: • GP 11 How to Check a Sensor. • P/J407, Carriage PWB. • 11C-170 HCSS BM Power Distribution RAP. Install new components as necessary: • Carriage PWB, PL 11.72 Item 5. • Compiler carriage assembly, PL 11.72 Item 1 Go to Flag 3. Check the connectors and harness between P/J412 and P/J432. Also check connectors and harness P/J401 and P/J428, refer to GP 7. The wiring and connectors are good. Y↓N→Repair the wiring, or install new components as necessary.

Code: 11-012-130, 11-014-130, 11-315-130, 11-316-130

Description: Compiler Carriage Position Failure RAP 11-012-130 The compiler carriage is not at the home position. 11-014-130 The compiler carriage fails to move. 11-315-130 The carriage upper limit switch is actuated. 11-316-130 The carriage lower limit switch is actuated. NOTE: The home position is with the compiler carriage at the upper limit position.
Remedy: NOTE: All HCSS interlocks must be made to supply +24V to the motors. Enter dC330, code 11-315. Actuate the carriage upper limit switch, S11-315. The display changes. Y↓N→Go to Flag 1. Check the switch. Refer to: • GP 13, How to Check a Switch. • P/J415, HCSS PWB. • 11C-130 HCSS Power Distribution RAP. Install new components as necessary: • Carriage upper limit switch, PL 11.44 Item 1. • HCSS PWB, PL 11.56 Item 5. Enter dC330, code 11-316. Actuate the carriage lower limit switch, S11-316. The display changes. Y↓N→Go to Flag 2. Check the switch. Refer to: • GP 13, How to Check a Switch. • P/J415, HCSS PWB. • 11C-130 HCSS Power Distribution RAP. Install new components as necessary: • Carriage lower limit switch, PL 11.44 Item 10. • HCSS PWB, PL 11.56 Item 5. Enter dC330, codes 11-014 CC motor move up, then, 11-016 CC motor move down. The compiler carriage moves between the top and bottom limits. Y↓N→Go to Flag 3. Check the compiler carriage elevator motor, MOT11-013. Refer to: • GP 10, How to Check a Motor. • P/J415, HCSS PWB. • 11C-130 HCSS Power Distribution RAP. Install new components as necessary: • Compiler carriage elevator motor, PL 11.44 Item 8. • HCSS PWB, PL 11.56 Item 5. Enter dC330, code 11-317. Actuate the Compiler carriage safety switch, S11-317. The display changes. Y↓N→Go to Flag 4. Check the switch. Refer to: • GP 13, How to Check a Switch. • P/J406, Carriage PWB. • 11C-130 HCSS Power Distribution RAP. Install new components as necessary: • Carriage PWB, PL 11.46 Item 5. • Compiler carriage safety switch, PL 11.47 Item 4. Go to Flag 5, check the harness and connectors P/J410 and P/J434, refer to GP 7. The wiring and connectors are good. Y↓N→Repair the wiring or install new components as necessary. Perform SCP 6 Final Actions.
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie