• Code: 11-030-170, 11-336-170
• Description: Bin 1 Movement Failure RAP 11-030-170 Bin 1 fails to move. 11-336-170 Bin 1 is not at the home position.
• Remedy: NOTE: All HCSS BM interlocks must be made to supply +24V to the motors. Enter dC330, codes 11-032 bin 1 elevator motor down to run the bin 1 elevator motor, MOT11- 030. MOT11-030 runs. Y↓N→Go to Flag 2. Check MOT11-030. Refer to: • GP 10, How to Check a Motor. • P/J424, HCSS PWB. • 11C-170 HCSS BM Power Distribution RAP. Install new components as necessary: • Bin 1 elevator motor, PL 11.78 Item 11. • HCSS PWB, PL 11.92 Item 5. Enter dC330, codes 11-032 bin 1 elevator motor down, then 11-030 bin 1 elevator motor home. Bin 1 moves away from, then back to, the home position. Y↓N→Check the bin 1 front and rear elevator belts: • Ensure that both belts are correctly positioned on the upper and lower pulleys. • Ensure that bin 1 is securely clamped to both elevator belts. Enter dC330, code 11-035, actuate the bin 1 empty sensor, Q11-035. The display changes. Y↓N→Go to Flag 1. Check the sensor Q11-035. Refer to: • GP 11, How to Check a Sensor. • P/J416, HCSS PWB. • 11C-170, HCSS BM Power Distribution RAP. Install new components as necessary: • Bin 1 empty sensor, PL 11.78 Item 5. • HCSS PWB, PL 11.92 Item 5. Enter dC330, code 11-334, actuate the bin 1 upper limit switch, S11-334. The display changes. Y↓N→Go to Flag 3. Check the switch S11-334. Refer to: • GP 13, How to Check a Switch. • P/J424, HCSS PWB. • 11C-170 HCSS BM Power Distribution RAP. Install new components as necessary. • Bin 1 upper limit switch S11-334, PL 11.78 Item 1. • HCSS PWB, PL 11.92 Item 5. Enter dC330, code 11-335, actuate the bin 1 lower limit switch, S11-335. The display changes. Y↓N→Go to Flag 4. Check the switch S11-335. Refer to: • GP 13, How to Check a Switch. • P/J424, HCSS PWB. • 11C-170 HCSS BM Power Distribution RAP. Install new components as necessary. • Bin 1 lower limit switch S11-335, PL 11.78 Item 2. • HCSS PWB, PL 11.92 Item 5. Perform SCP 6 Final Actions.

• Code: 11-031-130, 11-337-130
• Description: Bin 1 Offset Failure RAP 11-031-130 Bin 1 fails to offset. 11-337-130 Bin 1 is not at the offset home position.
• Remedy: NOTE: All HCSS interlocks must be made to supply +24V to the motors. Enter dC330, code 11-034 Bin 1 offset motor run. Bin 1 moves. Y↓N→Go to Flag 2. Check the bin 1 offset motor, MOT11-034. Refer to: • GP 10, How to Check a Motor. • P/J416, HCSS PWB. • 11C-130 HCSS Power Distribution RAP. Install new components as necessary: • HCSS PWB, PL 11.56 Item 5. • Bin 1 offset motor, PL 11.52 Item 6. Enter dC330, code 11-337. Actuate the Bin 1 offset sensor, Q11-337. The display changes. Y↓N→Go to Flag 1. Check the sensor Q11-337. Refer to: • GP 11, How to Check a Sensor. • P/J416, HCSS PWB. • 11C-130 HCSS Power Distribution RAP. Install new components as necessary: • HCSS PWB, PL 11.56 Item 5. • Bin 1 offset sensor, PL 11.52 Item 7. Perform SCP 6 Final Actions.

• Code: 11-031-170, 11-337-170
• Description: Bin 1 Offset Failure RAP 11-031-170 Bin 1 fails to offset. 11-337-170 Bin 1 is not at the offset home position.
• Remedy: NOTE: All HCSS BM interlocks must be made to supply +24V to the motors. Enter dC330, code 11-034 Bin 1 offset motor run. Bin 1 moves. Y↓N→Go to Flag 2. Check the bin 1 offset motor, MOT11-034. Refer to: • GP 10, How to Check a Motor. • P/J416, HCSS PWB. • 11C-170 HCSS BM Power Distribution RAP. Install new components as necessary: • HCSS PWB, PL 11.92 Item 5. • Bin 1 offset motor, PL 11.78 Item 6. Enter dC330, code 11-337, actuate the Bin 1 offset sensor, Q11-337. The display changes. Y↓N→Go to Flag 1. Check the sensor Q11-337. Refer to: • GP 11, How to Check a Sensor. • P/J416, HCSS PWB. • 11C-170 HCSS BM Power Distribution RAP. Install new components as necessary: • HCSS PWB, PL 11.92 Item 5. • Bin 1 offset sensor, PL 11.78 Item 7. Perform SCP 6 Final Actions.

• Code: 11-036-130, 11-346-130
• Description: Bin 2 Movement Failure RAP 11-036-130 Bin 2 fails to move. 11-346-130 Bin 2 is not at the home position. NOTE: The home position is at the uppermost position.
• Remedy: NOTE: All HCSS interlocks must be made to supply +24V to the motors. Enter dC330, codes 11-038, bin 2 elevator motor down to run the bin 2 elevator motor, MOT11- 036. MOT11-036 runs. Y↓N→Go to Flag 2. Check MOT11-036. Refer to: • GP 10, How to Check a Motor. • P/J431, HCSS PWB. • 11C-130 HCSS Power Distribution RAP. Install new components as necessary: • Bin 2 elevator motor, PL 11.54 Item 11. • HCSS PWB, PL 11.56 Item 5. Enter dC330, codes 11-038 bin 2 elevator motor down, then 11-036 bin 2 elevator motor home. Bin 2 moves away from, then back to, the home position. Y↓N→Check the bin 2 front and rear elevator belts: • Ensure that both belts are correctly positioned on the upper and lower pulleys. • Ensure that bin 2 is securely clamped to both elevator belts. Enter dC330, code 11-344. Actuate the bin 2 upper limit switch, S11-344. The display changes. Y↓N→Go to Flag 3. Check the switch S11-344. Refer to: • GP 13, How to Check a Switch. • P/J431, HCSS PWB. • 11C-130 HCSS Power Distribution RAP. Install new components as necessary. • Bin 2 upper limit switch, PL 11.54 Item 1. • HCSS PWB, PL 11.56 Item 5. Enter dC330, code 11-345. Actuate the bin 2 lower limit switch, S11-454. The display changes. Y↓N→Go to Flag 4. Check the switch S11-345. Refer to: • GP 13, How to Check a Switch. • P/J431, HCSS PWB. • 11C-130 HCSS Power Distribution RAP. Install new components as necessary. • Bin 2 lower limit switch, PL 11.54 Item 2. • HCSS PWB, PL 11.56 Item 5. Enter dC330, code 11-346. Actuate the bin 2 empty sensor, S11-041. The display changes. Y↓N→Go to Flag 1. Check the sensor S11-041. Refer to: • GP 13, How to Check a Sensor. • P/J418, HCSS PWB. • 11C-130 HCSS Power Distribution RAP. Install new components as necessary: • Bin 2 empty sensor, PL 11.54 Item 5. • HCSS PWB, PL 11.56 Item 5. Perform SCP 6 Final Actions.

• Code: 11-040-130, 11-347-130
• Description: Bin 2 Offset Failure RAP 11-040-130 Bin 2 fails to offset. 11-347-130 Bin 2 is not at the offset home position NOTE: The offset home position is with bin 2 to the rear.
• Remedy: NOTE: All HCSS interlocks must be made to supply +24V to the motors. Enter dC330, code 11-040 bin 2 offset motor run. Bin 2 moves. Y↓N→Go to Flag 2. Check the bin 2 offset motor, MOT11-040. Refer to: • GP 10, How to Check a Motor. • P/J418, HCSS PWB. • 11C-130 HCSS Power Distribution RAP. Install new components as necessary: • HCSS PWB, PL 11.56 Item 5. • Bin 2 offset motor, PL 11.54 Item 6. Enter dC330, code 11-347. Actuate the bin 2 offset sensor, Q11-347. The display changes. Y↓N→Go to Flag 1. Check the sensor Q11-347. Refer to: • GP 11, How to Check a Sensor. • P/J418, HCSS PWB. • 11C-130 HCSS Power Distribution RAP. Install new components as necessary: • HCSS PWB, PL 11.56 Item 5. • Bin 2 offset sensor, PL 11.54 Item 7. Perform SCP 6 Final Actions.

• Code: 11-043-110, 11-350-110
• Description: Hole Punch Operation Failure RAP 11-043-110 The hole punch fails to perform a punch cycle. 11-350-110 The hole punch is not at the home position.
• Remedy: • Check the 2K LCSS PWB DIP switch settings, refer to 11F-110 2K LCSS PWB DIP Switch Settings RAP. • Check that the hole punch is present and correctly installed. • Check that the punch has not jammed in the down position. This can occur with transparencies and labels. NOTE: The home position of the punch unit is when the cut-out in the actuator is between the punch head home sensor jaws.
  NOTE: In diagnostics, actuating any 2K LCSS sensor or switch can change the displayed state on the UI. Make sure that the correct sensor or switch is tested. Go to Flag 5, check the link between P/J307 pins 10 and 11, 2K LCSS PWB. The link is good. Y↓N→Repair the wiring or connector. Enter dC330, code 11-351, actuate the punch head present sensor, Q11-351. The display changes. Y↓N→Go to Flag 2 and check Q11-351. Refer to: • 11G-110 2K LCSS PWB Damage RAP. • GP 11 How to Check a Sensor. • P/J307, 2K LCSS PWB. • 11D-110 2K LCSS Power Distribution RAP. Repair or install new components as necessary: • Punch head present sensor, PL 11.6 Item 1. • 2K LCSS PWB, PL 11.26 Item 1. Enter dC330 code 11-350, actuate the punch head home sensor, Q11-350. The display changes. Y↓N→Go to Flag 1 and check Q11-350. Refer to: • 11G-110 2K LCSS PWB Damage RAP. • GP 11 How to Check a Sensor. • P/J307, 2K LCSS PWB. • 11D-110 2K LCSS Power Distribution RAP. Repair or install new components as necessary: • Punch head home sensor, PL 11.6 Item 1. • 2K LCSS PWB, PL 11.26 Item 1. Enter dC330 code 11-043. The punch cycles. Y↓N→Go to Flag 3. Check the hole punch motor MOT11-042. Refer to: • 11G-110 2K LCSS PWB Damage RAP. • GP 10, How to Check a Motor. • P/J311, 2K LCSS PWB. • 11D-110 2K LCSS Power Distribution RAP. Repair or install new components as necessary: • Hole punch motor assembly, PL 11.6 Item 2. • 2K LCSS PWB, PL 11.26 Item 1. NOTE: The chad bin collects the pieces of paper cut out by the hole punch. The chad bin level sensor will not operate if the tray is incorrectly installed. Ensure the chad bin is fully inserted and the lever engages in the slot. Enter dC330, code 11-348., actuate the chad bin level sensor, Q11-348 using a strip of paper. The display changes. Y↓N→Go to Flag 4 and check Q11-340. Refer to: • 11G-110 2K LCSS PWB Damage RAP. • GP 11 How to Check a Sensor. • P/J307, 2K LCSS PWB. • 11D-110 2K LCSS Power Distribution RAP. Install new components as follows. • Chad bin level sensor, PL 11.6 Item 7. • 2K LCSS PWB, PL 11.26 Item 1. Perform SCP 6 Final Actions.

• Code: 11-043-130
• Description: Hole Punch Cycle Failure RAP 11-043-130 The hole punch fails to complete a cycle of operation. NOTE: The home position of the punch unit is when the cutout in the actuator is between the punch head home sensor jaws.
• Remedy: NOTE: All HCSS interlocks must be made to supply +24V to the motors. Enter dC330, codes 11-043 punch head run, then 11-042 punch head move home.. The punch cycles, then goes to the home position. Y↓N→Go to Flag 3. Check the hole punch motor, MOT11-042. Refer to: • GP 10, How to Check a Motor. • P/J421, HCSS PWB. • 11C-130 HCSS Power Distribution RAP. Install new components as necessary: • Hole punch motor, PL 11.38 Item 7. • HCSS PWB, PL 11.56 Item 5. Enter dC330, code 11-110. Actuate the punch position sensor, Q11-110. The display changes. Y↓N→Go to Flag 1. Check the sensor, Q11-110. Refer to: • GP 11, How to Check a Sensor. • P/J420, HCSS PWB. • 11C-130 HCSS Power Distribution RAP. Install new components as necessary: • Punch position sensor, PL 11.38 Item 9. • HCSS PWB, PL 11.56 Item 5. Enter dC330, code 11-350. Actuate the hole punch home sensor, Q11-350 The display changes. Y↓N→Go to Flag 2. Check the sensor, Q11-350. Refer to: • GP 11, How to Check a Sensor. • P/J420, HCSS PWB. • 11C-130 HCSS Power Distribution RAP. Install new components as necessary: • Hole punch home sensor, PL 11.38 Item 8. • HCSS PWB, PL 11.56 Item 5. Perform SCP 6 Final Actions.

• Code: 11-043-170, 11-350-170
• Description: Hole Punch Cycle Failure RAP 11-043-170 The hole punch fails to complete a cycle of operation.
• Remedy: NOTE: All HCSS BM interlocks must be made to supply +24V to the motors. Enter dC330, codes 11-043 punch head run and 11-042 punch head move home.. The punch cycles continuously, then goes to the home position Y↓N→Go to Flag 3. Check the hole punch motor, MOT11-042. Refer to: • GP 10, How to Check a Motor. • P/J421, HCSS PWB. • 11C-170 HCSS BM Power Distribution RAP. Install new components as necessary: • Hole punch motor, PL 11.70 Item 7. • HCSS PWB, PL 11.92 Item 5. Enter dC330, code 11-350 actuate the punch head home sensor, Q11-350. The display changes. Y↓N→Go to Flag 2. Check the sensor, Q11-350. Refer to: • GP 11, How to Check a Sensor. • P/J420, BM PWB. • 11C-170 HCSS BM Power Distribution RAP. Install new components as necessary: • Punch head home sensor, PL 11.70 Item 8. • HCSS PWB, PL 11.92 Item 5. Enter dC330, code 11-110 actuate the punch head home sensor, Q11-110. The display changes. Y↓N→Go to Flag 1. Check the sensor, Q11-350. Refer to: • GP 11, How to Check a Sensor. • P/J420, BM PWB. • 11C-170 HCSS BM Power Distribution RAP. Install new components as necessary: • Punch sensor, PL 11.70 Item 9. • HCSS PWB, PL 11.92 Item 5. Perform SCP 6 Final Actions.