• Code: 11-100-170
• Description: HCSS BM Paper Entry RAP 11-100-170 The leading edge of the sheet is late to the HCSS BM.
• Remedy: Enter dC330, code 11-100, actuate the entry sensor, Q11-100. The display changes. Y↓N→Go to Flag 1. Check the sensor Q11-100. Refer to: • GP 11, How to Check a Sensor. • P/J420, HCSS PWB. • 11C-170 HCSS BM Power Distribution RAP. Install new components as necessary: • Entry sensor Q11-100, PL 11.70 Item 9. • HCSS PWB, PL 11.92 Item 5. Enter dC330, code 11-000 to run transport motor 1A, MOT 11-000. Transport motor 1A runs. Y↓N→Go to Flag 3 and the motor 1A, MOT 11-000. Refer to: • GP 10, How to Check a Motor. • P/J419, HCSS PWB. • 11C-170 HCSS BM Power Distribution RAP. Install new components as necessary: • Transport motor 1A, PL 11.70 Item 5. • HCSS PWB, PL 11.92 Item 5. Enter dC330, code 11-000 to run transport motor 1B, MOT 11-001. Transport motor 1B runs. Y↓N→Go to Flag 4 and check transport motor 1B. Refer to: • GP 10, How to Check a Motor. • P/J425, HCSS PWB. • 11C-170 HCSS BM Power Distribution RAP. Install new components as necessary: • Transport motor 1B, PL 11.70 Item 5. • HCSS PWB, PL 11.92 Item 5. Enter dC330, code 11-002 to energize the diverter solenoid, SOL 11-002. The diverter solenoid energizes. Y↓N→Go to Flag 2 and check the solenoid, SOL11-002. Refer to: • GP 12, How to Check a Solenoid or Clutch. • P/J421, HCSS PWB. • 11C-170 HCSS BM Power Distribution RAP. Install new components as necessary: • Diverter solenoid SOL11-002, PL 11.66 Item 3. • HCSS PWB, PL 11.92 Item 5. Perform SCP 6 Final Actions.

• Code: 11-100-171, 11-101-171
• Description: HVF Entry Sensor RAP 11-100-171 The paper leading edge is late arriving at the entry sensor. 11-101-171 The paper trailing edge is late leaving the entry sensor.
• Remedy: . shows the location of the components. Enter dC330, code 11-100. Manually operate the entry sensor, Q11-100. The display changes. Y↓N→Go to Flag 1. Check the sensor, Q11-100. Refer to: • GP 11 How to Check a Sensor. • P/J101, HVF Control PWB • 11A-171 HVF Power Distribution RAP Install new components as necessary: • Entry sensor, PL 11.156. • HVF Control PWB, PL 11.157 Item 2. Enter dC330, code 11-000 to run the Entry feed motor 1, MOT 11-000. The motor runs. Y↓N→Go to Flag 2. Check the entry feed motor 1, MOT 11-000. Refer to: • GP 10 How to Check a Motor. • P/J102, HVF Control PWB • 11A-171 HVF Power Distribution RAP Install new components as necessary: • Entry feed motor 1, PL 11.150 Item 12 • HVF control PWB, PL 11.157 Item 2. Check the drive belt on the motor. The drive belt is good. Y↓N→Install a new drive belt, PL 11.150 Item 13. The fault may be intermittent, check for damaged wiring or bad connectors. If necessary install new components: • Entry sensor, PL 11.156 • Entry feed motor 1, PL 11.150 Item 12. • HVF control PWB, PL 11.157 Item 2.

• Code: 11-110-110
• Description: Sheet Late to Hole Punch RAP 11-110-110 Sheet late at the punch sensor.
• Remedy: Check the following: • The 2K LCSS PWB DIP switch settings, refer to 11F-110 2K LCSS PWB DIP Switch Settings RAP. • Ensure the paper tray guides are set to the correct position for the size of paper in the tray. • For a paper jam at the entrance to the 2K LCSS. Check that there is no obstruction that would prevent a sheet from arriving in position for punching, refer to the 11H-110 Copy Damage in the 2K LCSS RAP. • The punch sensor, Q11-110 for chad debris.
  NOTE: In diagnostics, actuating any 2K LCSS sensor or switch can change the displayed state on the UI. Make sure that the correct sensor or switch is tested.. Enter dC330, code 11-110. Actuate the punch sensor, Q11-110. The display changes. Y↓N→Go to Flag 1 and check Q11-110. Refer to: • 11G-110 2K LCSS PWB Damage RAP. • GP 11, How to Check a Sensor. • P/J307, 2K LCSS PWB. • 11D-110 2K LCSS Power Distribution RAP Repair or install new components as necessary: • Punch sensor, PL 11.6 Item 7. • 2K LCSS PWB, PL 11.26 Item 1. Perform SCP 6 Final Actions.

• Code: 11-110-130
• Description: Hole Punch Jam RAP 11-110-130 A sheet is late arriving at the punch position sensor.
• Remedy: Enter dC330, code 11-110. Actuate the punch position sensor, Q11-110. The display changes. Y↓N→Go to Flag 1. Check the sensor Q11-110. Refer to: • GP 11, How to Check a Sensor. • P/J420, HCSS PWB. • 11C-130 HCSS Power Distribution RAP. Install new components as necessary: • Punch position sensor, PL 11.38 Item 9. • HCSS PWB, PL 11.56 Item 5. Enter dC330, code 11-348. Actuate the chad bin level sensor, Q11-348. NOTE: The chad bin collects the pieces of paper (chad) cut out by the punch. The chad bin must be correctly installed for the chad bin level sensor to operate. The display changes. Y↓N→Go to Flag 2. Check the chad bin level sensor Q11-348. Refer to: • GP 11 How to Check a Sensor. • P/J422, HCSS PWB. • 11C-130 HCSS Power Distribution RAP. Install new components as necessary. • Chad bin level sensor, PL 11.36 Item 8. • HCSS PWB, PL 11.56 Item 5. Perform SCP 6 Final Actions.

• Code: 11-110-170
• Description: Hole Punch Jam RAP 11-110-170 A sheet is late arriving at the punch position sensor.
• Remedy: Enter dC330, code 11-110. Actuate the punch sensor, Q11-110. The display changes. Y↓N→Go to Flag 1. Check the sensor Q11-110. Refer to: • GP 11, How to Check a Sensor. • P/J420, HCSS PWB. • 11C-170 HCSS BM Power Distribution RAP. Install new components as necessary: • Punch sensor, PL 11.70 Item 9. • HCSS PWB, PL 11.92 Item 5. Enter dC330, code 11-348. Actuate the chad bin level sensor, Q11-348. NOTE: The chad bin collects the pieces of paper (chad) cut out by the punch. The chad bin must be correctly installed for the chad bin level sensor to operate. The display changes. Y↓N→Go to Flag 2. Check the sensor Q11-348. Refer to: • GP 11 How to Check a Sensor. • P/J422, HCSS PWB. • 11C-170 HCSS BM Power Distribution RAP. Install new components as necessary. • Chad bin level sensor, PL 11.66 Item 8. • HCSS PWB, PL 11.92 Item 5. Perform SCP 6 Final Actions.

• Code: 11-120-130, 11-122-130
• Description: Compiler Carriage Jam RAP 11-120-130 The lead edge of a sheet is late arriving at the compiler sensor. 11-122-130 the trail edge of a sheet or set is late leaving the compiler sensor.
• Remedy: NOTE: All HCSS interlocks must be made to supply +24V to the motors. Enter dC330, code 11-120. Actuate the compiler sensor, Q11-120. The display changes. Y↓N→Go to Flag 1. Check the sensor, Q11-120. Refer to: • GP 11 How to Check a Sensor. • P/J409, Carriage PWB. • 11C-130 HCSS Power Distribution RAP. Install new components as necessary: • Carriage PWB, PL 11.46 Item 5. • Compiler sensor, PL 11.48 Item 7. Enter dC330, code 11-001 to run transport motor 2, MOT 11-001. The motor runs. Y↓N→Go to Flag 3. Check the motor MOT 11-001. Refer to: • GP 10, How to Check a Motor. • P/J403, Carriage PWB. • 11C-130 HCSS Power Distribution RAP. Install new components as necessary: • Carriage PWB, PL 11.46 Item 5. • Transport motor 2, PL 11.48 Item 18. Enter dC330, code 11-010 to run the compiler carriage eject roll motor, MOT 11-010. The motor runs. Y↓N→Go to Flag 2. Check the motor MOT 11-010. Refer to: • GP 10, How to Check a Motor. • P/J408, Carriage PWB. • 11C-130 HCSS Power Distribution RAP. Install new components as necessary: • Carriage PWB, PL 11.46 Item 5. • Compiler carriage eject roll motor, PL 11.49 Item 1. Enter dC330, code 11-023 to run the eject motor, MOT 11-020. The eject housing cycles between open and closed. Y↓N→Go to Flag 4. Check the motor MOT 11-020. Refer to: • GP 10, How to Check a Motor. • P/J406, Carriage PWB. • 11C-130 HCSS Power Distribution RAP. Install new parts as necessary: • Carriage PWB, PL 11.46 Item 5. • Eject motor assembly, PL 11.47 Item 2. Enter dC330, code 11-000 to run the transport motor 1B. The motor runs. Y↓N→Go to Flag 6 and check transport motor 1B. Refer to: • GP 10, How to Check a Motor. • P/J425, HCSS PWB • 11C-130 HCSS Power Distribution RAP. Install new components as necessary: • Transport motor 1B, PL 11.38 Item 5. • HCSS PWB, PL 11.56 Item 5. Check the transport motor 1B drive belt and belt tensioner. If necessary install new parts: • Transport motor 1B drive belt, PL 11.38 Item 3. • Belt tensioner, PL 11.38 Item 1. Go to Flag 5, check the harness and connectors P/J412 and P/J432, refer to GP 7. The wiring and connectors are good. Y↓N→Repair the wiring or install new components. Perform SCP 6 Final Actions.

• Code: 11-120-170, 11-122-170
• Description: Compiler Carriage Jam RAP 11-120-170 The lead edge of a sheet is late arriving at the compiler sensor. 11-122-170 the trail edge of a sheet or set is late leaving the compiler sensor.
• Remedy: Enter dC330, code 11-120. Actuate the compiler sensor, Q11-120. The display changes. Y↓N→Go to Flag 1. Check the sensor, Q11-120. Refer to: • GP 11 How to Check a Sensor. • P/J409, Carriage PWB. • 11C-170 HCSS BM Power Distribution RAP. Install new components as necessary: • Carriage PWB, PL 11.72 Item 5. • Compiler sensor, PL 11.74 Item 7. Enter dC330, code 11-001 to run transport motor 2, MOT11-001. Transport motor 2, MOT 11-001 runs. Y↓N→Go to Flag 3. Check the motor MOT11-001. Refer to: • GP 10, How to Check a Motor. • P/J403, Carriage PWB. • 11C-170 HCSS BM Power Distribution RAP. Install new components as necessary: • Carriage PWB, PL 11.72 Item 5. • Transport motor 2, PL 11.74 Item 18. Enter dC330, code 11-010 to run the compiler carriage eject roll motor, MOT11-010. The motor runs. Y↓N→Go to Flag 2. Check the motor MOT11-010. Refer to: • GP 10, How to Check a Motor. • P/J408, Carriage PWB. • 11C-170 HCSS BM Power Distribution RAP. Install new components as necessary: • Carriage PWB, PL 11.72 Item 5. • Compiler carriage eject roll motor, PL 11.75 Item 1. Enter dC330, code 11-023 to run the eject motor, MOT11-020. The compiler cycles between open and closed. Y↓N→Go to Flag 4. Check the motor MOT11-020. Refer to: • GP 10, How to Check a Motor. • P/J406, Carriage PWB. • 11C-170 HCSS BM Power Distribution RAP. Install new parts as necessary: • Carriage PWB, PL 11.72 Item 5. • Eject motor, PL 11.73 Item 2. Go to Flag 5, check the harness and connectors P/J412 and P/J432, refer to GP 7. The harness and connectors are good. Y↓N→Repair the harness, or install new parts as necessary. Perform SCP 6 Final Actions.

• Code: 11-130-110, 11-132-110
• Description: Paper Exiting to Bin 0 RAP 11-130-110 The leading edge of the sheet is late to the top exit sensor. 11-132-110 The trailing edge of the sheet is late from the top exit sensor.
• Remedy: Check the following: • 2K LCSS PWB DIP switch settings, refer to 11F-110 2K LCSS PWB DIP Switch Settings RAP. • Ensure the paper tray guides are set to the correct position for the size of paper in the tray. • The tensioner on the intermediate paper drive belt. Check that the tensioner is free to move and that the tensioner pulley is free to rotate. If necessary lubricate the tensioner and tensioner pulley-110. Refer to GP 18 Machine Lubrication. NOTE: The tensioner arm and the tensioner pulley require different lubricants, -110. • The drive pulleys on both transport motor 1 and 2 are secure and do not slip on the motor shaft. • All the transport drive belts are correctly fitted and are in a good condition • All he transport rolls and idler pulleys are free to rotate. • The diverter gate and linkage for free movement. • A paper jam in the path to bin 0. • Torn paper fragments from a previous jam clearance action. • A paper jam in the path to the top tray. If the jams occur shortly after install. Check the gap between the entry guide cover, PL 11.24 Item 5 and the paper guide PL 11.22 Item 10. If the gap is less than 1 mm, adjust or install a new entry guide cover. Refer to the replacement procedure-110. Refer to the 11H-110 Copy Damage in the 2K LCSS RAP and the 11J-110 Mis-Registration in Stapled Sets and Non-Stapled Sets RAP. NOTE: Paper is diverted to bin 0 when the diverter gate solenoid is energized. Paper is fed to bin 1 when the diverter gate solenoid is de-energized.
  NOTE: All 2K LCSS interlocks must be made to supply +24V to the motors. NOTE: In diagnostics, actuating any 2K LCSS sensor or switch can change the displayed state on the UI. Make sure that the correct sensor or switch is tested. Enter dC330, code 11-001 to run transport motor 2, MOT11-001. The motor runs. Y↓N→Go to Flag 3 and check MOT11-001. Refer to: • 11G-110 2K LCSS PWB Damage RAP. • GP 10, How to Check a Motor. • P/J309, 2K LCSS PWB. • 11D-110 2K LCSS Power Distribution RAP. Repair or install new components as necessary: • Transport motor 2, PL 11.22 Item 5. • 2K LCSS PWB, PL 11.26 Item 1. Enter dC330, code 11-002 to energize the diverter gate solenoid, S11-002. The diverter gate solenoid energizes. Y↓N→Go to Flag 2 and check SOL11-002. Refer to: • 11G-110 2K LCSS PWB Damage RAP. • GP 12, How to Check a Solenoid. • P/J306, 2K LCSS PWB. • 11D-110 2K LCSS Power Distribution RAP. Repair or install new components as necessary: • Diverter gate solenoid, PL 11.22 Item 12. • 2K LCSS PWB, PL 11.26 Item 1. Enter dC330, code 11-130, actuate the top exit sensor, Q11-130. The display changes. Y↓N→Go to Flag 1 and check Q11-130. Refer to: • 11G-110 2K LCSS PWB Damage RAP. • GP 11, How to Check a Sensor. • P/J313, 2K LCSS PWB. • 11D-110 2K LCSS Power Distribution RAP. Repair or install new components as necessary: • Top exit sensor, PL 11.22 Item 11. • 2K LCSS PWB, PL 11.26 Item 1. Enter dC330, code 11-000 to energize the transport motor 1, MOT 11-000. The motor energizes. Y↓N→Go to Flag 4 and check MOT 11-000. Refer to: • 11G-110 2K LCSS PWB Damage RAP. • GP 10, How to Check a Motor. • P/J305, 2K LCSS PWB. • 11D-110 2K LCSS Power Distribution RAP. Repair or install new components as necessary: • Transport motor 1, PL 11.14 Item 2.