• Code: 11-320-110, 11-322-110
• Description: Ejector Movement Failure RAP 11-320-110 The ejector is not at the home position. 11-322-110 The ejector fails to perform a cycle of operation. NOTE: A cycle of operation for the ejector is to cycle from the home position to the out position and back to the home position.
• Remedy: NOTE: All 2K LCSS interlocks must be made to supply +24V to the motors. NOTE: In diagnostics, actuating any 2K LCSS sensor or switch can change the displayed state on the UI. Make sure that the correct sensor or switch is tested. Enter dC330, code 11-322, actuate the ejector out sensor, Q11-322. The display changes. Y↓N→Go to Flag 2. Check Q11-322. Refer to: • 11G-110 2K LCSS PWB Damage RAP. • GP 11 How to Check a Sensor. •. • P/J304, 2K LCSS PWB. • 11D-110 2K LCSS Power Distribution RAP. Repair or install new components as necessary: • Ejector out sensor, Q11-322, PL 11.18 Item 3. • 2K LCSS PWB, PL 11.26 Item 1. Enter dC330, code 11-320, actuate the ejector home sensor, Q11-320. The display changes. Y↓N→Go to Flag 1. Check Q11-320. Refer to: • 11G-110 2K LCSS PWB Damage RAP. • GP 11 How to Check a Sensor. •. • P/J304, 2K LCSS PWB. • 11D-110 2K LCSS Power Distribution RAP. Repair or install new components as necessary: • Ejector home sensor, Q11-320, PL 11.18 Item 3. • 2K LCSS PWB, PL 11.26 Item 1. Enter dC330, code 11-023 to check the movement of the ejector. The ejector motor runs. Y↓N→Go to Flag 3. Check the ejector motor, MOT11-020. Refer to: • 11G-110 2K LCSS PWB Damage RAP. • GP 10, How to Check a Motor. •. • P/J303, 2K LCSS PWB. • 11D-110 2K LCSS Power Distribution RAP. Repair or Install new components as necessary: • Ejector assembly, PL 11.18 Item 1. • 2K LCSS PWB, PL 11.26 Item 1. The ejector cycles noisily, colliding with the end stops. Y↓N→Check the stapler to ensure the staples are correctly formed. Mis-formed staples can cause the set to hang in the stapler causing ejector movement failures. The staples are correctly formed. Y↓N→Clear the staple head of any mis-formed staples, then check the operation of the stapler. If necessary, install a new staple head unit, PL 11.20 Item 5. If the ejector is still not moving, install a new ejector assembly, PL 11.18 Item 1. Perform SCP 6 Final Actions. Go to Flag 4. +5v is available at P/J304 between pins 7 and 8. Y↓N→Go to the 11D-110 2K LCSS Power Distribution RAP. Connect a service meter at P/J304 between pins 8 and 9. Slowly rotate the ejector motor encoder. The voltage changes between +5V and 0V. Y↓N→Go to Flag 4. Check the wiring and connectors between the ejector motor encoder sensor and the 2K LCSS PWB. If necessary repair the wiring. If the wiring is good, install a new ejector motor encoder sensor, PL 11.18 Item 3. Perform the 11G-110 2K LCSS PWB Damage RAP, if necessary install a new 2K LCSS PWB, PL 11.26 Item 1.

• Code: 11-320-120, 11-322-120
• Description: Ejector Movement Failure RAP 11-320-120 The ejector is not at the home position. 11-322-120 The ejector fails to perform a cycle of operation. NOTE: A cycle of operation for the ejector is to move from the home position to the out position and back to the home position.
• Remedy: NOTE: All 1K LCSS interlocks must be made to supply +24V to the motors. NOTE: In diagnostics, actuating any 1K LCSS sensor or switch can change the displayed state on the UI. Make sure that the correct sensor or switch is tested. NOTE: For clarity, the 1K LCSS is shown removed from the machine. Enter dC330, code 11-322, ejector out sensor, Q11-322. Actuate Q11-322. The display changes. Y↓N→Go to Flag 2. Check Q11-322. Refer to: • 11F-120 1K LCSS PWB Damage RAP. • GP 11 How to Check a Sensor. •. • P/J8, 1K LCSS PWB • 11C-120 1K LCSS Power Distribution RAP. Repair or install new components as necessary: • Ejector out sensor, Q11-322, PL 11.114 Item 3. • 1K LCSS PWB, PL 11.124 Item 1. Enter dC330, code 11-320, ejector home sensor, Q11-320. Actuate Q11-320. The display changes. Y↓N→Go to Flag 1. Check Q11-320. Refer to: • 11F-120 1K LCSS PWB Damage RAP. • GP 11 How to Check a Sensor. •. • P/J8, 1K LCSS PWB • 11C-120 1K LCSS Power Distribution RAP. Repair or install new components as necessary: • Ejector home sensor, Q11-320, PL 11.114 Item 3. • 1K LCSS PWB, PL 11.124 Item 1. Enter dC330, code 11-023 to check the operation of the ejector motor, MOT11-020. MOT11- 020 runs. Y↓N→Go to Flag 3. Check MOT11-020. Refer to: • 11F-120 1K LCSS PWB Damage RAP. • GP 10, How to Check a Motor. •. • P/J15, 1K LCSS PWB • 11C-120 1K LCSS Power Distribution RAP. Repair or Install new components as necessary: • Ejector assembly, PL 11.114 Item 1. • 1K LCSS PWB, PL 11.124 Item 1. The ejector cycles noisily, colliding with the end stops. Y↓N→Check the stapler to ensure the staples are correctly formed, refer to the 11-364-120 Stapling Failure RAP. Mis-formed staples can cause the set to hang in the stapler causing ejector movement failures. The staples are correctly formed. Y↓N→Clear the staple head of any mis-formed staples, then check the operation of the stapler. If necessary, install a new staple head unit, PL 11.116 Item 5. If the ejector is still not moving, install a new ejector assembly, PL 11.114 Item 1. Perform SCP 6 Final Actions. Go to Flag 4. +5V is available at P/J8 between pins 7 and 8. Y↓N→Go to the 11C-120 1K LCSS Power Distribution RAP. Connect a service meter at P/J8 between pins 8 and 9. Slowly rotate the ejector motor encoder. The voltage changes between +5V and 0V. Y↓N→Go to Flag 4. Check the wiring and connectors between the ejector motor encoder sensor and the 1K LCSS PWB. If necessary repair the wiring. If the wiring is good, install a new ejector motor encoder sensor, PL 11.114 Item 3. Perform the 11F-120 1K LCSS PWB Damage RAP, if necessary install a new 1K LCSS PWB, PL 11.124 Item 1.

• Code: 11-320-130, 11-322-130
• Description: Compiler Ejector Movement Failure RAP 11-320-130 The compiler ejector is not at the home position. 11-322-130 The compiler ejector fails to complete a cycle of operation. NOTE: The home position for the compiler ejector is with the ejector closed. NOTE: A cycle of operation for the compiler ejector is to cycle between closed to open, then back to closed.
• Remedy: Enter dC330, codes 11-023 to run the ejector motor. The ejector opens fully, then closes. Y↓N→Go to Flag 3. Check the ejector motor, MOT 11-020. Refer to: • GP 10, How to Check a Motor. • P/J406, Carriage PWB. • 11C-130 HCSS Power Distribution RAP. Install new components as necessary: • Carriage PWB, PL 11.46 Item 5. • Ejector motor assembly, PL 11.47 Item 2. Enter dC330, code 11-320, actuate the ejector home sensor, Q11-320. The display changes. Y↓N→Go to Flag 1 and Flag 4. Check the sensor. Refer to: • GP 11, How to Check a Sensor. • P/J409 and P/J411, Carriage PWB. • 11C-130 HCSS Power Distribution RAP. Install new components as necessary: • Carriage PWB, PL 11.46 Item 5. • Ejector home sensor, PL 11.47 Item 3. Enter dC330, code 11-317, actuate the compiler carriage safety switch, S11-317. The display changes. Y↓N→Go to Flag 2. Check the compiler carriage safety switch. Refer to: • GP 13 How to Check a Switch. • P/J406, Carriage PWB. • 11C-130 HCSS Power Distribution RAP. Install new components as necessary: • Carriage PWB, PL 11.46 Item 5. • Compiler Carriage safety switch, PL 11.47 Item 4. Go to Flag 5, check the harness and P/J412 and P/J432, refer to GP 7. The wiring and connectors are good. Y↓N→Repair the wiring or install new components. Perform SCP 6 Final Actions.

• Code: 11-320-170, 11-322-170
• Description: Compiler Ejector Movement Failure RAP 11-320-170 The compiler ejector is not at the home position. 11-322-170 The compiler ejector fails to complete a cycle of operation. NOTE: The home position for the compiler ejector is with the ejector closed. NOTE: A cycle of operation for the compiler ejector is to move between closed to open, then back to closed.
• Remedy: Enter dC330, code 11-023 to run the eject motor, MOT11020. The ejector opens fully and then closes. Y↓N→Go to Flag 3. Check the ejector motor, MOT 11-020. Refer to: • GP 10, How to Check a Motor. • P/J406, Carriage PWB. • 11C-170 HCSS BM Power Distribution RAP. Install new components as necessary: • Carriage PWB, PL 11.72 Item 5. • Ejector motor assembly, PL 11.73 Item 2. Enter dC330, code 11-320, actuate the ejector home sensor, Q11-320. The display changes. Y↓N→Go to Flag 1 and Flag 4. Check the sensor, Q11-320. Refer to: • GP 11, How to Check a Sensor. • P/J409 and P/J411, Carriage PWB. • 11C-170 HCSS BM Power Distribution RAP. Install new components as necessary: • Carriage PWB, PL 11.72 Item 5. • Ejector home sensor, PL 11.73 Item 3. Enter dC330, code 11-317, actuate the compiler carriage safety switch, S11-317. The display changes. Y↓N→Go to Flag 2. Check the switch, S11-317. Refer to: • GP 13, How to Check a Switch. • P/J406, Carriage PWB. • 11C-170 HCSS BM Power Distribution RAP. Install new components as necessary: • Carriage PWB, PL 11.72 Item 5. • Compiler carriage safety switch, PL 11.73 Item 4. Go to Flag 5, check the connectors and harness between P/J412 and P/J432, refer to GP 7. The harness and connectors are good. Y↓N→Repair the harness, or install new components. Perform SCP 6 Final Actions.

• Code: 11-334-130, 11-335-130, 11-336-130
• Description: Bin 1 Elevate Failure RAP 11-334-130 The bin 1 upper limit switch has been made. 11-335-130 The bin 1 lower limit switch has been made. 11-336-130 Bin 1 fails to move to the home position.
• Remedy: Enter dC330, codes 11-030, 11-031, 11-032 and 11-033 to run the bin 1 elevator motor, MOT 11-030. Check the movement of bin 1. Bin 1 moves correctly. Y↓N→Go to Flag 3. Check the bin 1 elevator motor, MOT 11-030. Refer to: • GP 10, How to Check a Motor. • P/J424, HCSS PWB. • 11C-130 HCSS Power Distribution RAP. Install new components as necessary: • Bin 1 elevator motor, PL 11.52 Item 11. • HCSS PWB, PL 11.56 Item 5. Enter dC330, code 11-334, actuate the bin 1 upper limit switch, S11-334. The display changes. Y↓N→Go to Flag 2. Check the switch S11-334. Refer to: • GP 13, How to Check a Switch. • P/J424, HCSS PWB. • 11C-130 HCSS Power Distribution RAP. Install new components as necessary: • Bin 1 upper limit switch, PL 11.52 Item 1. • HCSS PWB, PL 11.56 Item 5. Enter dC330, code 11-335, actuate the bin 1 lower limit switch, S11-335. The display changes. Y↓N→Go to Flag 1. Check the switch S11-335. Refer to: • GP 13, How to Check a Switch. • P/J424, HCSS PWB. • 11C-130 HCSS Power Distribution RAP. Install new components as necessary: • Bin 1 lower limit switch, PL 11.52 Item 2. • HCSS PWB, PL 11.56 Item 5. Perform SCP 6 Final Actions.

• Code: 11-334-170, 11-335-170, 11-336-170
• Description: Bin 1 Elevate Failure RAP 11-334-170 The bin 1 upper limit switch has been actuated. 11-335-170 The bin 1 lower limit switch has been actuated. 11-336-170 Bin 1 fails to move to the home position.
• Remedy: Enter dC330, codes 11-030, 11-031, 11-032 and 11-033, to check the movement of bin 1. Bin 1 moves correctly. Y↓N→Go to Flag 3. Check the bin 1 elevator motor, MOT 11-030. Refer to: • GP 10, How to Check a Motor. • P/J424, HCSS PWB. • 11C-170 HCSS BM Power Distribution RAP. Install new components as necessary: • Bin 1 elevator motor, PL 11.78 Item 11. • HCSS PWB, PL 11.92 Item 5. Enter dC330, code 11-334, actuate the bin 1 upper limit switch, S11-334. The display changes. Y↓N→Go to Flag 2. Check the switch S11-334. Refer to: • GP 13, How to Check a Switch. • P/J424, HCSS PWB. • 11C-170 HCSS BM Power Distribution RAP. Install new components as necessary: • Bin 1 upper limit switch, PL 11.78 Item 1. • HCSS PWB, PL 11.92 Item 5. Enter dC330, code 11-335, actuate the top bin 1 lower limit switch, S11-335. The display changes. Y↓N→Go to Flag 1. Check the switch S11-335. Refer to: • GP 13, How to Check a Switch. • P/J424, HCSS PWB. • 11C-171 HCSS BM Power Distribution RAP.

• Code: 11-344-130, 11-345-130, 11-346-130
• Description: Bin 2 Elevate Failure RAP 11-344-130 The bin 2 upper limit switch has been made. 11-345-130 The bin 2 lower limit switch has been made. 11-346-130 Bin 2 fails to move to the home position.
• Remedy: Enter dC330, codes 11-036, 11-037, 11-038 and 11-039 to run the bin 2 elevator motor, MOT 11-030. Check the movement of bin 2. Bin 2 moves correctly. Y↓N→Go to Flag 3. Check the bin 2 elevator motor, MOT11-030. Refer to: • GP 10, How to Check a Motor. • P/J431, HCSS PWB. • 11C-130 HCSS Power Distribution RAP. Install new components as necessary: • Bin 2 elevator motor, PL 11.54 Item 11. • HCSS PWB, PL 11.56 Item 5. Enter dC330, code 11-344. Actuate the bin 2 upper limit switch, S11-344. The display changes. Y↓N→Go to Flag 2. Check the switch, S11-344. Refer to: • GP 13 How to Check a Switch. • P/J431, HCSS PWB. • 11C-130 HCSS Power Distribution RAP. Install new components as necessary: • Bin 2 upper limit switch, PL 11.54 Item 1. • HCSS PWB, PL 11.56 Item 5. Enter dC330, code 11-345. Actuate the bin 2 lower limit switch, S11-345. The display changes. Y↓N→Go to Flag 1. Check the switch, S11-345. Refer to: • GP 13 How to Check a Switch. • P/J431, HCSS PWB. • 11C-130 HCSS Power Distribution RAP. Install new components as necessary: • Bin 2 lower limit switch, PL 11.54 Item 2. • HCSS PWB, PL 11.56 Item 5. Perform SCP 6 Final Actions

• Code: 11-350-130
• Description: Hole Punch Not Home RAP 11-350-130 The hole punch is not at the home position. NOTE: The home position of the punch unit is when the cutout in the actuator is between the punch head home sensor jaws.
• Remedy: Enter dC330, codes 11-043 punch head run, then 11-042 punch head move home.. The punch cycles then goes to the home position Y↓N→Go to Flag 2. Check the hole punch motor, MOT11-042. Refer to: • GP 10, How to Check a Motor. • PJ421, HCSS PWB. • 11C-130 HCSS Power Distribution RAP. Install new components as necessary: • Hole punch motor, PL 11.38 Item 7. • HCSS PWB, PL 11.56 Item 5. Enter dC330, code 11-350 actuate the hole punch home sensor, Q11-350. The display changes. Y↓N→Go to Flag 1. Check the sensor, Q11-350. Refer to: • GP 11, How to Check a Sensor. • PJ420, HCSS PWB. • 11C-130 HCSS Power Distribution RAP. Install new components as necessary: • Hole punch home sensor, PL 11.38 Item 8. • HCSS PWB, PL 11.56 Item 5. Perform SCP 6 Final Actions.