Code :

Code: 0201
Display: Print Unable 02 Turn the power off and then back on again.
Description: Synchronization signal from the main motor cannot be detected. Or the main motor speed is unstable after a set period of time.
Causes: 1 Main motor harness connection failure 2 Harness connection failure between the low-voltage power supply PCB and main PCB 3 Main motor failure 4 Low-voltage power supply PCB failure 5 Main PCB failure

Code: 0202
Display: Print Unable 02 Turn the power off and then back on again.
Description: Synchronization signal from the process motor cannot be detected. Or the process motor speed is unstable after a set period of time.
Causes: 1 Process motor harness connection failure 2 Harness connection failure between the low-voltage power supply PCB and main PCB 3 Process motor failure 4 Low-voltage power supply PCB failure 5 Main PCB failure

Code: 0501
Display: Print Unable 05 Turn the power off and then back on again.
Description: The center thermistor of the fuser unit does not reach the specified temperature within the specified time.
Causes: 1 Connection failure of the center or side thermistor harness of the fuser unit 2 Connection failure of the heater harness of the fuser unit 3 Harness connection failure of the eject sensor PCB 4 Harness connection failure of the low-voltage power supply PCB 5 Eject sensor PCB failure 6 Fuser unit failure 7 Low-voltage power supply PCB failure 8 Main PCB failure

Code: 0502
Display: Print Unable 05 Turn the power off and then back on again.
Description: The center thermistor of the fuser unit does not reach the specified temperature within the specified time.
Causes: 1 Connection failure of the center or side thermistor harness of the fuser unit 2 Connection failure of the heater harness of the fuser unit 3 Harness connection failure of the eject sensor PCB 4 Harness connection failure of the low-voltage power supply PCB 5 Eject sensor PCB failure 6 Fuser unit failure 7 Low-voltage power supply PCB failure 8 Main PCB failure

Code: 0503
Display: Print Unable 05 Turn the power off and then back on again.
Description: The center thermistor of the fuser unit detected a temperature higher than the specified value.
Causes: 1 Connection failure of the center or side thermistor harness of the fuser unit 2 Connection failure of the heater harness of the fuser unit 3 Harness connection failure of the eject sensor PCB 4 Harness connection failure of the low-voltage power supply PCB 5 Eject sensor PCB failure 6 Fuser unit failure 7 Low-voltage power supply PCB failure 8 Main PCB failure

Code: 0504
Display: Print Unable 05 Turn the power off and then back on again.
Description: After the center thermistor of the fuser unit was normally heated, it detected a temperature lower than the specified value.
Causes: 1 Connection failure of the center or side thermistor harness of the fuser unit 2 Connection failure of the heater harness of the fuser unit 3 Harness connection failure of the eject sensor PCB 4 Harness connection failure of the low-voltage power supply PCB 5 Eject sensor PCB failure 6 Fuser unit failure 7 Low-voltage power supply PCB failure 8 Main PCB failure

Code: 0505
Display: Print Unable 05 Turn the power off and then back on again.
Description: The center thermistor of the fuser unit detected a temperature rise greater than the specified value within a set period of time.
Causes: 1 Connection failure of the center or side thermistor harness of the fuser unit 2 Connection failure of the heater harness of the fuser unit 3 Harness connection failure of the eject sensor PCB 4 Harness connection failure of the low-voltage power supply PCB 5 Eject sensor PCB failure 6 Fuser unit failure 7 Low-voltage power supply PCB failure 8 Main PCB failure

1 2 3 4 > Last ›