• Code: E025-0000
• Description: Connector disconnection of the Hopper Toner Sensor (TS1)
  The connection signal of the Hopper Toner Sensor (TS1) was not detected 10 times in a row for 100msec.
  * If paper is being fed, the error occurs after the paper has been delivered.
• Remedy: 1. Check the connector connection between the Hopper Unit and the DC Controller PCB (PCB1).
  2. Replace the Hopper Unit.
  3. Replace the DC Controller PCB (PCB1).

• Code: E025-0001
• Description: Bottle Motor (M5) rotation error
  The same level of the Bottle Motor (M5) lock signal was detected 230 times in a row while detecting the signal every 2.0msec.
  * If paper is being fed, the error occurs after the paper has been delivered.
• Remedy: 1. Check the connector connection between the Bottle Motor (M5) and the DC Controller PCB (PCB1).
  2. Replace the Bottle Motor (M5).
  3. Replace the DC Controller PCB (PCB1).

• Code: E110-0001
• Description: Laser Scanner Motor rotation error
  After startup of the Laser Scanner Motor, the speed lock signal of the Laser Scanner Motor was not detected although a specified period of time had passed.
  *When the same status was detected again after executing an error retry.
• Remedy: 1. Check the connector connection between the Laser Scanner Unit and the DC Controller PCB (PCB1).
  2. Replace the Laser Scanner Unit.
  3. Replace the DC Controller PCB (PCB1).

• Code: E110-0002
• Description: Laser Scanner Motor rotation error
  After the speed lock of the Laser Scanner Motor settled, the speed lock signal was not detected 10 times in a row at intervals of 100msec.
  *When the same status was detected again after executing an error retry.
• Remedy: 1. Check the connector connection between the Laser Scanner Unit and the DC Controller PCB (PCB1).
  2. Replace the Laser Scanner Unit.
  3. Replace the DC Controller PCB (PCB1

• Code: E110-0003
• Description: Laser Scanner Motor rotation error
  The speed lock signal of the Laser Scanner Motor was not detected although 6.5 seconds (when switching from low speed to normal speed) or 8.0 seconds (when switching from normal speed to low speed) had passed.
  *When the same status was detected again after executing an error retry.
• Remedy: 1. Check the connector connection between the Laser Scanner Unit and the DC Controller PCB (PCB1).
  2. Replace the Laser Scanner Unit.
  3. Replace the DC Controller PCB (PCB1).

• Code: E196-0000
• Description: EEPROM access error
  During communication with EEPROM, the communication failed to retry 20 times after the communication error had occurred.
  * If paper is being fed, the error occurs after the paper has been delivered.
• Remedy: 1. Replace the DC Controller PCB (PCB1).

• Code: E197-0000
• Description: Laser Driver PCB communication error
  Error in communication with the Laser Driver PCB (communication data failure)
  *When the same status was detected again after executing an error retry.
• Remedy: 1. Check the connector connection between the Laser Scanner Unit and the Main Controller PCB (PCB2) or the DC Controller PCB (PCB1).
  2. Replace the Laser Scanner Unit.
  3. Replace the Main Controller PCB (PCB2).
  4. Replace the DC Controller PCB (PCB1).

• Code: E197-0003
• Description: Connector disconnection of the Laser Scanner Unit
  The disconnection of the Laser Scanner Unit was detected.
• Remedy: 1. Check the connector connection between the Laser Scanner Unit and the Main Controller PCB (PCB2) or the DC Controller PCB (PCB1).
  2. Replace the Laser Scanner Unit.
  3. Replace the Main Controller PCB (PCB2).
  4. Replace the DC Controller PCB (PCB1).