• Code: 584-8002-02
• Description: Error in the stack delivery lower/shutter motor (Finisher-X1)
• Causes: The shutter HP sensor does not detect the shutter when the Stack Delivery Lower/Shutter Motor has been driven for 3 seconds.
• Remedy: [Related parts] - Harnesses from the Shutter HP Sensor (S106) to the Finisher Controller PCB - Harnesses from the Stack Delivery Lower/Shutter Motor (M122) to the Finisher Controller PCB - Shutter HP Sensor (S106) - Stack Delivery Lower/Shutter Motor (M122) - Finisher Controller PCB (PBA101) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustments> Adjustment when Replacing the Parts" in the Service Manual.

• Code: 584-8003-02
• Description: Error in the Stack Delivery Lower/Shutter Motor (Finisher-X1)
• Causes: The shutter does not come off the Shutter Close Detection Sensor when the Stack Delivery Lower/ Shutter Motor has been driven for 3 seconds.
• Remedy: [Related parts] - Harnesses from the Shutter Close Detection Sensor (S148) to the Finisher Controller PCB - Harnesses from the Stack Delivery Lower/Shutter Motor (M122) to the Finisher Controller PCB - Shutter Close Detection Sensor (S148) - Stack Delivery Lower/Shutter Motor (M122) - Finisher Controller PCB [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustments> Adjustment when Replacing the Parts" in the Service Manual.

• Code: 584-8004-02
• Description: Error in the Stack Delivery Lower/Shutter Motor (Finisher-X1)
• Causes: The Shutter Close Detection Sensor does not detect the shutter when the Stack Delivery Lower/ Shutter Motor has been driven for 3 seconds.
• Remedy: [Related parts] - Harnesses from the Shutter Close Detection Sensor (S148) to the Finisher Controller PCB - Harnesses from the Stack Delivery Lower/Shutter Motor (M122) to the Finisher Controller PCB - Shutter Close Detection Sensor (S148) - Stack Delivery Lower/Shutter Motor (M122) - Finisher Controller PCB (PBA101) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustments> Adjustment when Replacing the Parts" in the Service Manual.

• Code: 590-8001-02
• Description: a. Error in the Punch Motor (Puncher Unit-BE1/BF1/BG1/BH1) b. Error in the Punch Motor (Puncher Unit-A1)
• Causes: a. During initialization, the Punch HP Sensor does not detect the Puncher when the Punch Motor has been driven for 500 msec. after the Puncher has come off the Punch HP Sensor. After initialization, the Punch Motor does not return to home position. b. The punch does not come off the Punch HP Sensor when the Punch Motor has been driven for 0.2 seconds.
• Remedy: a. Puncher Unit-BE1/BF1/BG1/BH1 [Related parts] - Harnesses from the Punch HP Sensor (S104) to the Puncher Driver PCB - Harnesses from the Punch Motor Clock Sensor (S105) to the Puncher Driver PCB - Harnesses from the Punch Motor (M102) to the Puncher Driver PCB - Punch HP Sensor (S104) - Punch Motor Clock Sensor (S105) - Punch Motor (M102) - Puncher Driver PCB (PCB1) - Finisher Controller PCB (PBA101) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> Action on parts replacement" in the Service Manual. b. Puncher Unit-A1 [Related parts] - Harnesses from the Punch HP Sensor 1 (PS303) to the Puncher Relay PCB - Harnesses from the Punch HP Sensor 2 (PS304) to the Puncher Relay PCB - Harnesses from the Punch Motor Clock Sensor (PS305) to the Puncher Relay PCB - Harnesses from the Punch Motor (M301) to the Puncher Relay PCB - Punch HP Sensor 1 (PS303) - Punch HP Sensor 2 (PS304) - Punch Motor Clock Sensor (PS305) - Punch Motor (M301) - Puncher Relay PCB (PCB302) - Puncher Controller PCB (PCB301) - Finisher Controller PCB (PCB101) [Points to note at work] When the Swing Guide Safety Switch (SW102) turns on at the detection timing of this error, this error code may be displayed. Accordingly, perform the following work before checking the related parts. 1. Check whether there is not the mulfunction in the swing guide unit. 2. Check whether there is not the mulfunction in the Swing Guide Safety Switch (SW102). [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] When replacing the Puncher Controller PCB, refer to "Adjustment> When Replacing the Parts" in the Service Manual. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> When Replacing the Parts" in the Service Manual.

• Code: 590-8002-02
• Description: a. Error in the Punch Motor (Puncher Unit-BE1/BF1/BG1/BH1) b. Error in the Punch Motor (Puncher Unit-A1)
• Causes: a. The Puncher does not come off the Punch HP Sensor when the Punch Motor has been driven for 200 msec. The Puncher does not come off the Punch HP Sensor during initialization. b. The Punch HP Sensor does not detect the punch during initialization. The Punch HP Sensor does not detect the punch when the Punch Motor has been driven for 0.4 seconds for returning the punch after the punch jam.
• Remedy: a. Puncher Unit-BE1/BF1/BG1/BH1 [Related parts] - Harnesses from the Punch HP Sensor (S104) to the Puncher Driver PCB - Harnesses from the Punch Motor Clock Sensor (S105) to the Puncher Driver PCB - Harnesses from the Punch Motor (M102) to the Puncher Driver PCB - Punch HP Sensor (S104) - Punch Motor Clock Sensor (S105) - Punch Motor (M102) - Puncher Driver PCB (PCB1) - Finisher Controller PCB (PBA101) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> Action on parts replacement" in the Service Manual. b. Puncher Unit-A1 [Related parts] - Harnesses from the Punch HP Sensor 1 (PS303) to the Puncher Relay PCB - Harnesses from the Punch HP Sensor 2 (PS304) to the Puncher Relay PCB - Harnesses from the Punch Motor Clock Sensor (PS305) to the Puncher Relay PCB - Harnesses from the Punch Motor (M301) to the Puncher Relay PCB - Punch HP Sensor 1 (PS303) - Punch HP Sensor 2 (PS304) - Punch Motor Clock Sensor (PS305) - Punch Motor (M301) - Puncher Relay PCB (PCB302) - Puncher Controller PCB (PCB301) - Finisher Controller PCB (PCB101) [Points to note at work] When the Swing Guide Safety Switch (SW102) turns on at the detection timing of this error, this error code may be displayed. Accordingly, perform the following work before checking the related parts. 1. Check whether there is not the mulfunction in the swing guide unit. 2. Check whether there is not the mulfunction in the Swing Guide Safety Switch (SW102). [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] When replacing the Puncher Controller PCB, refer to "Adjustment> When Replacing the Parts" in the Service Manual. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> When Replacing the Parts" in the Service Manual.

• Code: 590-8003-02
• Description: Punch Motor clock error (Puncher Unit-BE1/BF1/BG1/BH1)
• Causes: The drive pulse of the Punch Motor does not reach 100 pulses when the Punch Motor has been driven for 100 msec. after the Puncher has come off the Punch HP Sensor.
• Remedy: [Related parts] - Harnesses from the Punch HP Sensor (S104) to the Puncher Driver PCB - Harnesses from the Punch Motor Clock Sensor (S105) to the Puncher Driver PCB - Harnesses from the Punch Motor (M102) to the Puncher Driver PCB - Punch HP Sensor (S104) - Punch Motor Clock Sensor (S105) - Punch Motor (M102) - Puncher Driver PCB (PCB1) - Finisher Controller PCB (PBA101) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustments> Adjustment when Replacing the Parts" in the Service Manual.

• Code: 591-0001-02
• Description: Upper limit error with Punch Waste Sensor (Puncher Unit-BE1/BF1/BG1/BH1)
• Causes: The light-receiving voltage was 3.0V or less despite increase in sensor light-emission.
• Remedy: [Related parts] - Punch Waste Sensor (PCB2) - Puncher Driver PCB (PCB1) - Finisher Controller PCB (PBA101) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustments> Adjustment when Replacing the Parts" in the Service Manual.

• Code: 591-0002-02
• Description: Lower limit error with Punch Waste Sensor (Puncher Unit-BE1/BF1/BG1/BH1)
• Causes: The light-receiving voltage was 2.0V or more despite decrease in sensor light-emission.
• Remedy: [Related parts] - Punch Waste Sensor (PCB2) - Puncher Driver PCB (PCB1) - Finisher Controller PCB (PBA101) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustments> Adjustment when Replacing the Parts" in the Service Manual.